User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
Reference Manual
165
4 ATTACK
Adjusts the compressor’s attack time for each band.
5 RELEASE
Adjusts the compressor’s release time for each band.
6 LINK knob
Links and adjusts the four bands for the selected parameter. However, if a parameter in
any frequency region reaches its maximum or minimum value, the link operation is
disabled. Parameters that can be linked and adjusted are displayed in band colors as
shown below.
7 CROSSOVER
Adjusts the crossover frequency when splitting the frequency range into multiple bands.
8 CUE button
Cue-monitors the corresponding band output for each band. When the CUE button is
on, the button changes to the color shown below.
If the IN button is off, the uncompressed sound is cue-monitored. The CUE buttons for
multiple bands can be turned on at the same time.
9 MASTER GAIN knob
Adjusts the gain for the final output signal.
0 INPUT meter
Indicates the input level for the audio signals sent to each band.
A KNEE knob
Adjusts the compressor’s knee.
B IN button
Turns each band on or off. When this button is off, the band color for the selected area
changes to gray as shown below.
Also, when this button is off, the COMPRESSOR field for the selected band turns gray.
You can adjust each parameter even when this button is off.
C FLAVOUR button
Switches the type of compressor between accurate VCA operation and natural OPTO
operation.
D HARMONICS button
Switches on/off the analog circuitry that emulates musical overtones.