User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Recorder
Reference Manual
203
NOTE
• Depending on the firmware version, Dante Accelerator might not support redundant networking.
Refer to the following website to check whether your version of the Dante Accelerator firmware
supports redundant networking.
http://www.yamahaproaudio.com/
Playing a multi-track project
NOTE
If you save the DANTE INPUT PATCH settings in a library, the settings of the CL series console
can be switched conveniently (page 168).
STEP
1. Press the DANTE INPUT PATCH button in the RECORDER screen (Nuendo Live page).
2. In the DANTE INPUT PATCH window, press the PORT SELECT button for the port to
which you want to assign the signal from Nuendo Live.
3. In the list at the left of the PORT SELECT window, select the DVS you’re using with
Nuendo Live, and select the port you want to assign it to.
4. Press the + button located in the upper part of the window to switch the port, and
assign a DVS port to it in the same way.
5. When you have finished making settings, press the CLOSE button to exit the
window.
6. Press the “X” symbol in the upper right of the DANTE INPUT PATCH window to close
it.
7. In the Nuendo Live screen, press the START button.
8. Operate the channels so that sound is output.
9. To stop playback, press the STOP button.
RECORDER screen
(when selecting the Nuendo Live tab)
DANTE INPUT PATCH window
PORT SELECT window