User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
Reference Manual
219
METER
PEAK HOLD ON -
Turns the meter’s peak hold function on/off. Lit
when ON.
SURROUND METER -
For Surround mode, toggle between the
content to be shown in meters displayed in the
Function Access Area. The lamp is off for MIX 1-
6, and on for SURROUND MONITOR.
MIDI
PROGRAM CHANGE PGM 1-128
Transmit the corresponding MIDI message.
For NOTE ON, it goes OFF when the bank is
switched.
CONTROL CHANGE CC 1-31, 33-95, 102-119
NOTE ON
NOTE ON C-2 (0)
:
NOTE ON G 8 (127)
MONITOR
OUTPUT - Switch the monitor output on/off.
SELECTED CH ASSIGN -
While holding down this key, press the SEL key
of a MIX or MATRIX channel to switch the
assignment on/off. During this time, the [SEL]
LED will be lit if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
DIMMER ON -
Enable the dimmer and attenuate the monitor
signal.
SOURCE SELECT
STEREO L/R
Recall the selected signal to the monitor.
MONO (C)
LCR
PB OUT
OMNI1-2
OMNI3-4
OMNI5-6
OMNI7-8
DEFINE
SURROUND SOURCE
SELECT
*6)
Recall the selected signal to the surround
monitor.
SURROUND DOWN-
MIX
STEREO MONO
When this function is off (the lamp is off), the
setting returns to 5.1 monitor.
SURROUND SPEAKER
SOLO
When this function is on (the lamp is on), the
SURROUND MONITOR screen opens. When this
function is off (the lamp is off), the SURROUND
MONITOR screen closes.
L, R, C, Ls, Rs, LFE
This functionality is the same as the SPEAKER
MUTE function in the SURROUND MONITOR
screen. When the SOLO button is on, it
functions as a SOLO key.
MUTE
MASTER
MUTE GROUP 1
- Switch MUTE GROUP MASTER on/off.:
MUTE GROUP 8
ALL MUTE -
Turns all MUTE GROUP MASTER settings on/off
together.
FUNCTION
PARAMETER 1 PARAMETER 2 Description
NUENDO
LIVE
TRANSPORT
GO TO PROJECT START
Operate the transport functions of Nuendo Live.
GO TO PREV MARKER
REWIND
FAST FORWARD
GO TO NEXT MARKER
GO TO PROJECT END
Operate the transport functions of Nuendo Live.
CYCLE
STOP
START
REC
EASY RECORDING
PEAK CLEAR -
Clear the peak indicators of the Nuendo Live
screen.
ADD MARKER -
This function executes ADD MARKER of
NUENDO Live.
OSCILLATOR
OSCILLATOR ON - Switch the OSC on/off.
SELECTED CH ASSIGN -
While holding down this key, press a SEL key of
a channel to switch the assignment on/off.
During this time, the [SEL] LED will be lit if
assign is ON, or dark if OFF.
It goes OFF when the bank is switched.
DIRECT ASSIGN *1)
Assign the oscillator to the channel selected
from list 1).
PAGE
CHANGE
BOOKMARK -
Memorize the currently-selected screen (hold
down the key for two seconds or longer), or
display the last-memorized screen (Hold down
the key, then release it within two seconds).
Popup windows can also be memorized. In the
case of a rack, the number of that rack is also
memorized.
BOOKMARK with “SEL” -
Memorize the above BOOKMARK with the
addition of the SEL status.
PREVIOUS PAGE
- Display the previous/next page.
NEXT PAGE
CLOSE POPUP - Close the displayed window.
FUNCTION
PARAMETER 1 PARAMETER 2 Description