User Manual

Warning/Error Messages
Reference Manual
271
Warning/Error Messages
Message Meaning
5.1SOLO : Only input cue is enabled.
If switched to Surround mode, only the input channel can be cue-
monitored when CUE MODE is set to 5.1 SOLO. (Attempted to cue-
monitor a different channel.)
xxx Parameters Copied. Parameter xxx was copied to the copy buffer.
xxx Parameters Initialized. Parameter xxx was initialized.
xxx Parameters Pasted. Parameter xxx was pasted from the copy buffer.
xxx Parameters Swapped with Copy
Buffer.
Parameter xxx was exchanged with the contents of the copy buffer.
ALTERNATE FUNCTION: Turned off! ALTERNATE FUNCTION was turned off.
Cannot Assign!
In the USER DEFINED KEYS popup of the CL3/CL1, you attempted to
edit an item that cannot be edited for that model.
Cannot Bookmark This Popup. This popup window cannot be bookmarked.
Cannot Mount This Type of Device in
This Position.
You attempted to mount a specific device at a position where it cannot
be mounted.
Cannot Open This Page. This window cannot be opened.
Cannot Paste to Different Parameter
Type!
The parameter cannot be pasted to a different type.
Cannot Paste! Cannot paste the character string.
Cannot Recall! Failed to recall a scene memory or library.
Cannot Select This Channel.
You attempted to select a channel that cannot be operated due to your
user level or some other reason.
Cannot Store! Failed to store a scene memory or library.
Cannot Undo! You pressed the UNDO button when Undo was not available.
Channel Copied. Channel settings have been copied.
Channel Moved. Channel settings have been moved.
Channel Returned to Default Settings. Channel settings have been returned to the default settings.
Console initialized due to memory
mismatch.
All data has been initialized because the data in internal backup
memory has been lost, due to an update or failure of the backup
battery or some other reason. Please contact your Yamaha service
center listed at the end of the Owner’s Manual (separate document).
Corrupted data fixed! The data was fixed.
Couldn’t Access File. File on the USB flash drive could not be accessed for some reason.
Couldn’t Write File. File could not be saved to the USB flash drive.
Current User Changed. [xxx] Current user was changed to [xxx].
DANTE audio resource overflow. There are insufficient audio resources on the Dante audio network.
DANTE Connection Error!
The primary and secondary connections are incorrect in the daisy
chain connections.
DANTE is not working by GIGA bit. GIGA bit is not working on the Dante audio network.
DANTE is working at Secondary. The Dante audio network is working on a secondary port.
DANTE module Error! An error has occurred in a Dante module.
DANTE switched to secondary port.
Only the SECONDARY PORT is used, even though a CL series
console is being used via a redundancy connection.
DCA ROLL-OUT : DCA members
scrolling.
In DCA ROLL-OUT mode, the content is scrolled left to right in the
block.
Different File Format! Some Data was
not Loaded.
Data in an unsupported format was loaded.
Directory Not Empty!
You attempted to delete a directory, but failed because there were files
remaining in the directory.
Editor: Data Framing Error!
Editor: Data Overrun!
Invalid signals are being exchanged with CL Editor.
Editor: Rx Buffer Full! Too much data is being received at CL Editor’s input port.
Editor: Tx Buffer Full! Too much data is being sent from CL Editor’s output port.
EFFECT CUE: Turned Off.
CUE was defeated because you switched from the EFFECT popup
window or the premium rack popup window to a different screen.
Error occurred at Secondary Port.
The network cable of a redundant secondary port has been
disconnected.
External HA Connection Conflict!
External HA data could not be recalled, because the state of
connections to the external HA has changed since the scene was
stored.
External Power Supply is Cut Off!
The PW800 (EXT) power supply connected to the CL series console
has stopped operating.
Fader Bank Snapshot is Done. A snapshot was taken of the current bank settings.
File Access is Busy!
The following operation has not been performed yet because the USB
flash drive is being accessed.
File Already Exists!
The USB flash drive already contains a file/directory with the same
name as the one you are attempting to save, rename, or create.
File Error [xx]! Internal file access error
File Protected!
Overwriting was not possible because the file on the USB flash drive is
write-protected.
Flash Memory Initializing Finished. Memory initialization has been completed.
Help File Not Found! The help file has not been loaded.
Illegal Address! The IP address or gateway address settings are invalid.
Illegal DIP Switch Setting. The R series DIP switch settings are invalid.
Illegal MAC Address! Cannot Use
Ethernet.
Communication via the Network connector is not possible because
the MAC address setting has been damaged for some reason.
Please contact your Yamaha service center listed at the end of the
Owner’s Manual (separate document).
Illegal MAC Address! The MAC Address is invalid.
Illegal Storage Format!
The USB flash drive could not be accessed because its format is
invalid or unsupported.
Message Meaning