GB PERSONAL RECEIVER RP-U200 PC AUX1 AUX2 TUNER POWER VIRTUAL 5.ICH DIGITAL USB PCM D.
The owner’s manual for this model consists of two volumes, “SET UP MANUAL” and “OPERATION MANUAL”. Le manuel d'utilisation pour ce modèle se compose de deux volumes, le “MANUEL DE CONFIGURATION” et le “MANUEL D’UTILISATION”. Die Anleitung für dieses Modell besteht aus zwei Teilen: aus dem “SET UP-HANDBUCH” und der “BEDIENUNGSANLEITUNG”.
CONTENTS Unpacking ........................................... Battery installation ............................. Battery replacement ........................... Remote control operation range ....... 2 2 2 2 Terminals and their functions ........... Connecting your computer ................ Connecting audio equipment ............ Connecting speakers ......................... Connecting an FM antenna ................ Plugging in this unit ...........................
GETTING STARTED Unpacking Battery installation After unpacking, check that the following items are supplied. Since the remote control will be used for many of this unit’s control operations, you should begin by installing the ● Remote control supplied batteries.
CONNECTIONS CONNECTIONS Never plug in this unit and other equipment until all connections are completed. 1. Make connections between this unit and other components by following the procedure below. 2. After all connections are finished, check that the connection cables are correctly connected. 3. After all connections are completed, plug in this unit and other equipment. Note Also, refer to the owner’s manual for other equipment in the system.
CONNECTIONS Connecting your computer Audio from your computer can be fed to this unit using any of the following connectors: USB, DIGITAL PC COAX IN, DIGITAL PC OPT IN, or ANALOG PC IN. If you use all of these connectors for connection, you can select the connector(s) to use on this unit’s front panel or the remote control. Connecting to the USB port (1) Connecting to digital inputs (3) If your computer has a USB port, connect it to this unit’s USB terminal using the supplied USB cable, as shown below.
CONNECTIONS Connecting audio equipment The following illustrations show how to connect a CD player, MD recorder, etc. using both analog and digital connections. However, it’s not necessary to make both connections. Audio connections Digital connections ● Be careful not to mix up the left and right connections. If you wish to record digital sound signals inputted to this unit, connect the optical digital input of an MD recorder or a DAT deck to this unit’s DIGITAL OPT OUT.
CONNECTIONS Connecting speakers To reproduce multi-channel surround sounds with this unit, connect five speakers (Yamaha NS-U40P, etc.) to this unit as follows: a pair of front speakers to the FRONT L and R terminals, a center speaker to the CENTER terminal, and a pair of surround speakers to the REAR L and R terminals. When using only one pair of speakers, connect one speaker to the FRONT L terminal, and the other to the FRONT R terminal. * Notes ● Use speakers which do not have a built-in amplifier.
CONNECTIONS Speaker Cables Strip 10 mm of insulation off the end of each speaker cable, and then twist the bare wires to prevent lose strands, which can cause short circuits. How to connect: 1 Press and hold the speaker connector levers. 2 Insert the bare ends of the speaker cables into the terminal holes. 10 mm 3 Then release the levers. * Try pulling gently on each cable to make sure that it is secure.
CONNECTIONS Setting up the speakers The role of the respective speakers In a 5.1-channel surround system, the front speakers are used for reproducing main channel sound (normal stereo sound) and effect sound. The surround speakers are used for surround and effect sounds, and the center speaker is for center channel sound (dialog, etc.). (The center speaker can be omitted if you prefer, however, the best result is obtained with a full five speaker system.
CONNECTIONS Connecting an FM antenna Connect an FM antenna to the FM ANT terminal of this unit by following the figure and procedures below. Indoor FM antenna (supplied) Outdoor FM antenna ANALOG R L PC IN AUX 1 IN F-type plug adaptor AUX 2 IN FM ANT 75Ω UNBAL. SUB WOOFER REC OUT OUTPUT R — L DIGITAL SPEAKERS + L (U.S.A. model) CONNECTIONS ANTENNA 75Ω coaxial cable USB FRONT It is recommended to use an outdoor FM antenna for good reception.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE INSTALLING USB DRIVER AND APPLICATION SOFTWARE When connecting this unit and your computer with the USB cable and controlling this unit from the computer, you must install the following software on your computer. ◆ USB driver software: Necessary for this unit to communicate with your computer ..........
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Installing the software Microsoft Windows 98/98SE or Windows Me 䡵 Installing and checking the USB driver 1 Turn on your computer and, if it’s not running already, start Windows 98/98SE or Windows Me. 2 Plug the AC power cord of this unit into the AC outlet. 9 Click the “+” symbol next to “Human Interface Devices”, and make sure that “HID-compliant consumer control device” and “USB Human Interface Device” appear in the list, as shown.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Make the following settings on your computer after the installation of the driver is finished. Setting of Audio and Audio CD [Windows 98/98SE only] * * Checking sound output and adjusting volume [Windows 98/98SE and Windows Me] Terminate all the activated applications. When using Windows 98SE, restart Windows, first. PC 1 2 AUX2 TUNER VIRTUAL 5.ICH DIGITAL USB PCM D. DSP PROLOGIC FM AM ST Double-click the “Multimedia” icon.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 Installing the Application Software * Terminate all the activated applications (including virus checkers) on the computer first. 1 This section explains how to uninstall the Application Software. 1 Terminate the Application Software and online help. 2 Click the Windows “Start” button and select “Settings”, and then “Control Panel”.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Microsoft Windows 2000 Professional 䡵 Installing and checking the USB driver 1 Turn on your computer and, if it’s not running already, start Windows 2000 Professional, and log in with Administrator. 2 Plug the AC power cord of this unit into the AC outlet. 9 Click the “+” symbol next to “Human Interface Devices”, and make sure that “HID-compliant consumer control device” and “USB Human Interface Device” appear in the list, as shown.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Make the following settings on your computer after the installation of the driver is finished. Setting of Audio and Audio CD 1 Checking sound output and adjusting volume Click the Windows “Start” button and select “Settings”, and then “Control Panel”. PC PC AUX1 AUX2 TUNER 2 Double-click the “Sounds and Multimedia” icon. 3 Click the “Audio” tab and select “USB Audio Device” at “Preferred device” of “Sound Playback”. VIRTUAL 5.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 Installing the Application Software 1 Insert the CD-ROM into the CD-ROM or DVD-ROM drive. 䡵 Uninstalling the Application Software This section explains how to uninstall the Application Software. 1 Terminate the Application Software and online help. 2 Click the Windows “Start” button and select “Settings”, and then “Control Panel”.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Macintosh computer 䡵 Connections and setup 1 Plug the AC power cord of this unit into the AC outlet. 2 Start the Macintosh. 3 Connect this unit to a USB port on the computer using the supplied USB cable. The driver software for USB audio is automatically installed. 4 Press the power switch of this unit to turn on this unit. Some messages are shown on the display. Checking sound output and adjusting volume PC TUNER VIRTUAL 5.ICH DIGITAL USB PCM D.
INSTALLING USB DRIVER AND APPLICATION SOFTWARE Next, install the Application Software and Online Help from the supplied CD-ROM. 䡵 How to use the Application Software and Online Help 䡵 Installing the Application Software All operating instructions for the Application Software is available from the Online Help. To refer to the instructions, select the Online Help from the menu displayed upon activation of the Application Software. 1 Insert the CD-ROM into the CD-ROM or DVD-ROM drive.
