English Benutzerhandbuch FR Mode d’emploi ES Manual de instrucciones PT Manual do Proprietário IT Manuale di istruzioni RU Руководство пользователя Pусский DE ₼㠖 Owner’s Manual About VST Rack 뼑霢꽩 EN Italiano Português Español Français Deutsch AUDIO INTERFACE INTERFACE AUDIO INTERFAZ DE AUDIO АУДИОИНТЕРФЕЙС 갉곸歲 킮쪎핳 ؕ؛ؔظ٭؛٤ ت٭ؘن٭ذ https://www.yamaha.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PA-12 1/2 PRECAUTIONS Water warning PLEASE READ CAREFULLY BEFORE PROCEEDING • Do not expose the product to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. Please keep this manual in a safe place for future reference.
PA-12 1/2 CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others. These precautions include, but are not limited to, the following: Location and connection • Do not place the product in an unstable position or a location with excessive vibration, where it might accidentally fall over and cause injury. • Keep this product out of reach of children. This product is not suitable for use in locations where children are likely to be present.
Information About functions bundled with the product Yamaha cannot be held responsible for damage caused by improper use or modifications to the product, or data that is lost or destroyed. • This product uses Dante Broadway. Refer to the Audinate website (English) for details on the open source licenses for the particular software. https://www.audinate.com/softwarelicensing • XLR-type connectors are wired as follows (IEC60268 standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).
Contents PRECAUTIONS....................................................................... 3 NOTICE ......................................................................................... 4 Information .................................................................................... 5 Introduction ............................................................................ 7 Main Features......................................................................... 7 How This Manual is Organized .........
Introduction Thank you for purchasing the RUio16-D audio interface. This product is for use by sound engineers, and uses VST plug-ins to expand the effects used by mixers. Make sure to read through this Owner’s Manual before using this product to make effective use of its various features. Also, make sure to keep this manual on hand after you have read it.
VST Rack Dante Controller VST Rack is an application that lets you build a software plug-in rack in combination with the RUio16-D. The software can also be used to configure the settings of this unit. Before using this product, download and install the VST Rack software from the website shown below onto your computer. https://www.yamaha.com/2/vst_rack/ Dante Controller is an application for configuring a Dante network and for routing audio.
Panel Controls and Functions Front panel 1 2 ) ! 3 4 1 Dante [SYSTEM] indicators 5 6 Operating status Normal Lights up green An abnormality has occurred if you have turned on the power but the green indicator is dark and the red indicator is either lit or flashing. If this happens, refer to “Messages” (page 20). 2 Dante [SYNC] indicators These indicators show the synchronization status of the Dante network and of this unit.
4 [PEAK] indicators This indicator lights when the volume of the input sound is too high (when it is only 3 dB before clipping). If the indicator lights frequently, turn the [GAIN] knob to the left to lower the volume. 5 [+48V] switch Turns the phantom power (+48V) on (lit) or off (unlit). When you turn this switch on, phantom power will be supplied to the XLR jack connected to the INPUT [CH15]/[CH16] jacks. Turn this switch on when using a phantom powered condenser microphone.
NOTE • In combination with VST Rack, this offers a function for detecting any abnormalities that may have occurred on the computer and automatically turning the bypass on. • The unit continuously operates in bypass mode when not connected to a computer. $ [PHONES] knob Adjusts the output signal level for the headphones. About output When this unit is starting up and you press the [BYPASS USB] switch, the signal from the computer can be output once the switch’s light turns off.
Rear Panel 1 2 4 5 6 7 1 [OUTPUT +4dBu] jacks 3 [POWER SOURCE] switch These are XLR-type analog output jacks. Connect an analog mixer, monitor speakers or related equipment here. You can adjust the output level with the [OUTPUT] knob on the front panel of this unit. This switch selects the jack used to supply power on this unit. Switch this to “USB 2.0 (PC)” to supply power from the [USB 2.0 (PC)] jack, or switch this to “5V DC IN” to supply power from the [5V DC IN] jack.
Using the 5V DC IN jack Even when this unit is connected to a computer, you can power this unit from an external power supply via the [5V DC IN] jack if the [POWER SOURCE] switch is switched to [5V DC IN]. Using an external power supply prevents the unit from operating erratically due to insufficient power from your computer’s USB port, and prevents noise-related problems caused by the power supply.
Before Using This Product Using with USB Bus Power 1. Move the [POWER SOURCE] switch on the rear panel to the left. Using with a USB Power Adaptor or USB Mobile Battery If the power supplied via bus power is insufficient, external power may need to be supplied from a commercially available USB power adapter or USB mobile battery. 1. Move the [POWER SOURCE] switch on the rear panel to the right. 2. Connect the included USB cable to the [USB 2.0] port on the rear panel. 3.
Basic Operations With this unit, you can process the signals from a Dante-enabled device such a digital mixer that are coming into input channels 1–16, send them to your computer via USB, process the signals using the effects in VST Rack, output the resulting signals via Dante channels 1–16 and play them back on the Dante-enabled device. NOTE • Use the Dante Controller for Dante audio patching. • Check the sounds below in your headphones as necessary.
Example 2: Sending audio (such as a mic signal) to a Danteenabled device • This sends the audio from devices connected to INPUT 15/16 to DANTE 15/16. Example 3: Listening to audio from your computer or Dante via monitor speakers • This outputs the analog signal from the computer’s MONITOR L/R. Set the [MONITOR/DANTE/USB] switch to “MONITOR.” • This outputs the analog signal that is input from DANTE 15/16. Set the [MONITOR/DANTE/USB] switch to “DANTE.
There are two ways to connect this product to a Dante network. Daisy Chain Network clock synchronization of desired data lines, QoS for prioritizing audio transmission and so on). Also, by creating a redundant network when using a star connection, you can build an environment that is much more robust in terms of failure than a daisy-chain network. A daisy chain is a wiring scheme in which multiple devices are connected together in sequence.
Attaching the Cable Hook Use the following steps to attach the cable hook that is included with this product, if you will use it. The cable hook helps prevent the USB cable from being accidentally yanked out during recording or in other situations. 1. Insert one of the tips of the cable hook that is included with this unit into the bottom part of the security slot, located at the center of the rear panel. 2.
Installing in a Rack You can install this unit onto a standard 19-inch rack shelf, using screws to hold it in place. Have ready two small M4 screws with a 0.7 mm pitch and a length of 6 mm. Line the threads of the screws up with those of the screw holes at the bottom of this unit, and install the screws into the panel. Check the dimensional drawing for the hole positions. NOTICE • The rubber feet should not be attached when using screws to hold the RUio16-D in place.
Restoring the Factory Default Settings (Initialization) Follow the steps below to initialize this device if you wish to reset the parameters configured using VST Rack or reset the Dante Broadway settings to their factory defaults. 1. Unplug the USB cable from the [5V DC IN] and [USB 2.0 (PC)] ports, and turn off the power. 2. Insert the USB cable while holding down the [BYPASS USB] switch on the front panel of this unit. All indicators on the front panel will flash while initialization is in progress.
[SYSTEM] indicators Lights up green Lights up green Lights up red Description Status As the settings have been changed using the Dante Controller, they do not match the actual Dante settings. If the Device Lock setting was enabled from Dante Controller, disable the setting. The internal memory has been corrupted. If the problem persists even after turning the power off and on again, consult your Yamaha dealer for repair.
General Specifications Sampling frequencies 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz Signal delay Less than 250 µs, Analog IN to Analog OUT @fs=96 kHz, BYPASS USB mode Power supply and voltage 5 V/1.5 A Power requirements 7.5 W Dimensions (W × H × D) 180 mm × 42 mm × 121 mm Weight 1.0 kg Operating temperature range 0–40°C Storage temperature range -20–60°C Included accessories USB 2.0 cable (type-A to type-C, 1.5 m) × 1, USB 2.0 cable (type-C to type-C, 1.
Dimensions 䠍䠎䠍 42 114.
Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.
Información para usuarios sobre la recogida y eliminación de los equipos antiguos Este símbolo en los productos, embalajes y documentos anexos significa que los productos eléctricos y electrónicos no deben mezclarse con los desperdicios domésticos normales. Para el tratamiento, recuperación y reciclaje apropiados de los productos antiguos, llévelos a puntos de reciclaje correspondientes, de acuerdo con la legislación nacional.
RUio16-D Owner’s Manual
RUio16-D Owner’s Manual
雅马哈乐器音响（中国）投资有限公司 上海市静安区新闸路 1818 号云和大厦 2 楼 客户服务热线：4000517700 公司网址：https://www.yamaha.com.cn 厂名 : 雅马哈电子（苏州）有限公司 厂址 : 江苏省苏州市苏州新区鹿山路 18 号 ヤマハ株式会社 〒430-8650 静岡県浜松市中区中沢町10-1 Yamaha Pro Audio global website http://www.yamahaproaudio.com/ Yamaha Downloads https://download.yamaha.
