Owner's Manual
Table Of Contents
- Easy Setup Guide
- Owners Manual
- Table of Contents
- Compatibility
- Supplied Accessories
- Parts & Controls
- Features
- Preparations
- General setup procedure
- Connecting speakers
- Connecting a TV
- Connecting playback devices
- Connecting the FM/AM antennas
- Connecting a network cable or the wireless antenna
- Connecting other devices
- Connecting the power cable
- Selecting an on-screen menu language
- Optimizing the speaker settings automatically (YPAO)
- Connecting to a network device wirelessly
- Playback
- Basic playback procedure
- Selecting the input source and favorite settings with one touch (SCENE)
- Selecting the sound mode
- Listening to FM/AM radio
- Playing back iPod music
- Playing back music stored on a USB storage device
- Playing back music stored on media servers (PCs/NAS)
- Listening to Internet radio
- Playing back music with AirPlay
- Playing back videos/audio in multiple rooms (multi-zone)
- Controlling the unit from a web browser (web control)
- Viewing the current status
- Configuring playback settings for different playback sources (Option menu)
- Configurations
- Configuring input sources (Input menu)
- Configuring the SCENE function (Scene menu)
- Configuring sound programs/surround decoders (Sound Program menu)
- Configuring various functions (Setup menu)
- Viewing information about the unit (Information menu)
- Configuring the system settings (ADVANCED SETUP menu)
- ADVANCED SETUP menu items
- Changing the speaker impedance setting (SPEAKER IMP.)
- Turning on/off the remote control sensor (REMOTE SENSOR)
- Selecting the remote control ID (REMOTE CON AMP)
- Switching the video signal type (TV FORMAT)
- Removing the limitation on HDMI video output (MONITOR CHECK)
- Backing up/recovering the settings (RECOV./BACKUP)
- Restoring the default settings (INITIALIZE)
- Updating the firmware (FIRM UPDATE)
- Checking the firmware version (VERSION)
- Controlling external devices with the remote control
- Updating the unit’s firmware via the network
- Frequently asked questions
- Troubleshooting
- Error indications on the front display
- Glossary
- Supported devices and file formats
- Video signal flow
- Multi-zone output
- Information on HDMI
- Reference diagram (rear panel)
- Specs
- Index
- Supplement for Web Control
- Quick Guide for Multi-zone and Remote Control Functions
- Supplement for SiriusXM Internet Radio
- Supplement for Rhapsody
- Supplement for Pandora
- Supplement for Spotify
- List of Remote Control Codes
- Additional Information: About Dolby Atmos
- Firmware Updating Procedure
- Scan of CD-ROM
- Warranty
PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO) En 50
Measuring at one listening position
(single measure)
When “Multi Position” is set to “No”, follow the procedure below for
measurement. It takes about 5 minutes to perform the
measurement.
• If any error message (such as E-1) or warning message (such as W-1) appears,
see “Error messages” (p.57) or “Warning messages” (p.58).
• (RX-A3040 only)
Do not use the microphone base until the corresponding message appear on the
TV.
1
To start the measurement, use the cursor keys to
select “Measure” and press ENTER.
The measurement will start in 10 seconds. Press ENTER
again to start the measurement immediately.
• To cancel the measurement temporarily, press RETURN.
The following screen appears on the TV when the
measurement finishes.
(RX-A2040)
(RX-A3040 [when angle/height measurement is disabled])
Proceed to Step 3.
(RX-A3040 [when angle/height measurement is enabled])
Proceed to Step 2.
2
Perform the angle/height measurement.
a Use the cursor keys to select “YES” and press ENTER.
Select “NO” to cancel the angle/height measurement.
b Attach the supplied pole to the center of the microphone base.
Microphone base
Pole
ENTER
RETURN
1 2 3 4 5 6 7 8 9 10
Cursor keys