Operation Manual
Table Of Contents
- Introduction
- FEATURES
- PREPARATIONS
- General setup procedure
- Connecting speakers
- Connecting a TV and playback devices
- Connecting the FM/AM antennas
- Connecting a network cable or preparing the wireless antenna
- Connecting other devices
- Connecting the power cable
- Selecting an on-screen menu language
- Configuring the necessary speaker settings
- Optimizing the speaker settings automatically (YPAO)
- Connecting to a network device wirelessly
- Connecting to the MusicCast network
- PLAYBACK
- Basic playback procedure
- Selecting the input source and favorite settings with one touch (SCENE)
- Selecting the sound mode
- Listening to FM/AM radio
- Playing back music via Bluetooth
- Playing back music stored on a USB storage device
- Playing back music stored on media servers (PCs/NAS)
- Listening to Internet radio
- Playing back iTunes/iPod music with AirPlay
- Playing back videos/audio in multiple rooms (multi-zone)
- Registering favorite items (shortcut)
- Controlling the unit from a web browser (web control)
- Viewing the current status
- Configuring playback settings for different playback sources (Option menu)
- CONFIGURATIONS
- Configuring input sources (Input menu)
- Configuring the SCENE function (Scene menu)
- Configuring sound programs/surround decoders (DSP Program menu)
- Configuring various functions (Setup menu)
- Viewing information about the unit (Information menu)
- Configuring the system settings (ADVANCED SETUP menu)
- ADVANCED SETUP menu items
- Changing the speaker impedance setting (SPEAKER IMP.)
- Turning on/off the remote control sensor (REMOTE SENSOR)
- Selecting the remote control ID (REMOTE CON AMP)
- Changing the FM/AM tuning frequency setting (TUNER FRQ STEP)
- Switching the video signal type (TV FORMAT)
- Removing the limitation on HDMI video output (MONITOR CHECK)
- Selecting the HDMI 4K signal format (4K MODE)
- Backing up/recovering the settings (RECOV./BACKUP)
- Restoring the default settings (INITIALIZE)
- Updating the firmware (FIRM UPDATE)
- Checking the firmware version (VERSION)
- Controlling external devices with the remote control
- Updating the unit’s firmware via the network
- APPENDIX
- List of remote control codes
En 137
Adjustment
Adjusts the delay between video and audio output manually when “Auto/Manual Select” is set
to “Manual”. You can fine-adjust the audio output timing when “Auto/Manual Select” is set to
“Auto”.
Setting range
0
ms to 500 ms (1 ms increments)
X
• When “Auto/Manual Select” is set to “Auto”, “Offset” shows the difference between automatic adjustment and
fine adjustment.
• This setting is also available in “Lipsync Adjustment” (p.117) in the “Option” menu.
⬛ Dynamic Range
Selects the dynamic range adjustment method for bitstream audio (Dolby Digital and DTS
signals) playback.
Settings
⬛ Max Volume
Sets the limit value of the volumes.
Setting range
-30.0 dB to +15.0 dB (5.0 dB increments), +16.5
dB
⬛ Initial Volume
Sets the initial volume when the receiver is turned on.
Settings
⬛ Pure Direct Mode
Selects whether to output video signals during the Pure Direct mode (p.82).
Settings
⬛ Adaptive DSP Level
Selects whether to automatically adjust the CINEMA DSP effect level.
Settings
Maximum
Produces audio without adjusting the dynamic range.
Standard Optimizes the dynamic range for regular home use.
Minimum/Auto
Sets the dynamic range for clear sound even at night or at low volumes.
When playing back Dolby TrueHD signals, the dynamic range is automatically
adjusted based on the input signal information.
Off Sets the level to the volume level of the unit when it last entered standby mode.
On
Sets at Mute or the specified volume level (-80.0 dB to +16.5 dB, 0.5 dB
increments).
(Specify a volume level which is lower than the “Max Volume” setting.)
Auto
Automatically outputs video signals when any videos are input from the selected
input source or an input source that can be operated with the on-screen display is
selected. When no video signals are input, the wall paper is displayed.
Video Off Does not output video signals including the wall paper.
Off Does not adjust the effect level automatically.
On
Adjusts the effect level automatically according to the YPAO measurement results
and the volume level.