BGR RX-V10MKII AV RECEIVER AMPLI-TUNER AUDIO-VIDEO OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING
CAUTION : READ THIS BEFORE OPERATING YOUR UNIT. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never remove the unit cover.
CONTENTS CAUTION ...................................................................2 BASIC TUNING OPERATION .................................27 FEATURES ................................................................4 Automatic tuning ......................................................27 Manual tuning ...........................................................27 PROFILE OF THIS UNIT ...........................................5 PRESET TUNING ....................................................
FEATURES ● 5 Speaker Configuration (Power Amp. Section) Main: 45W + 45W (8Ω) RMS Output Power, 0.04% THD, 20–20,000 Hz Center: 45W (8Ω) RMS Output Power, 0.04% THD, 1 kHz Rear: 15W + 15W (8Ω) RMS Output Power, 0.
You are the proud owner of a Yamaha stereo receiver –an extremely sophisticated audio component. The Digital Sound Field Processor (DSP) built into this unit takes advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences.
GETTING STARTED m Unpacking Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories. Indoor FM Antenna Remote Controller – LEVEL + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC V-AUX DVD/LD 2CH/6CH VCR DIR A DIR B REC/PAUSE – + PLAY A/B PRESET A/B/C/D/E DISC EFFECT ENHANCED ON/OFF PLAY TAPE TUNER CD PHONO POWER AM Loop Antenna /I SLEEP 75-ohm/300-ohm antenna adapter (U.K.
Since the remote controller will be used for many of this unit’s control operations, you should begin by installing the supplied batteries. 1. Turn the remote controller over and slide the battery compartment cover in the direction of the arrow. 2. Insert the batteries (R6, AA, UM-3 type) according to the polarity markings on the inside of the battery compartment. 3. Close the battery compartment cover.
SPEAKER SETUP Speakers to be used This unit is designed to provide the best sound-field quality with a 5-speaker configuration. The most effective speakers to use with this unit are main speakers, rear speakers, and a center speaker. You can do without the center speaker. (Refer to the “4-Speaker Configuration” shown below.) The main speakers are used for the main source sound. They could be the speakers from your present stereo system.
Caution: Plug in this unit and other components after all connections are completed. English CONNECTIONS m Connecting audio and video components All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components. * The output (or input) terminals of YAMAHA components numbered as 1, 3, 4, etc. on the rear panel must be connected to the same-numbered terminals of this unit.
ON SCREEN display If you connect a VCR, LD player, video monitor, etc. to this unit, you can display DSP program names and information about other settings and adjustments on the video monitor screen. Information is superimposed over the video image. If there is no image on the monitor, the information will be displayed over a monochromatic background. TV MODE PAL/NTSC switch (General model only) This unit is designed for use with the NTSC and PAL television formats.
English Connecting with 6 channel discrete outputs of a Dolby Digital decoder, DTS decoder or DVD player, etc. If you have a Dolby Digital decoder, DTS decoder or a DVD player etc. which incorporates a Dolby Digital decoder, DTS decoder or MPEG 2 decoder, its 6 channel discrete outputs can be connected to the DVD/LD 6CH DISCRT INPUT terminals of this unit. An example of connections: FM ANT 75Ω UNBAL.
m Connecting speakers Center speaker Note Use speakers with the specified impedance shown on the rear of this unit. Subwoofer system Rear speaker Rear speaker Left Right Main speaker Main speaker Left Right 8ΩMIN. /SPEAKER OUT SUB WOOFER REAR CENTER REAR SUB WOOFER CENTER MAIN MAIN SURROUND DVD/LD 6CH DISCRT INPUT 8ΩMIN./SPEAKER SPEAKERS (Europe model) How to Connect: Connect the SPEAKERS terminals to your speakers with the wire of the proper gauge (keep as short as possible).
English For connecting to the REAR and CENTER SPEAKERS terminals Red: positive (+) Black: negative (–) ➀ ➂ ➁ ➀ Press the tab. ➁ Insert the bare wire. [Remove approx. 5mm (1/4”) insulation from the speaker wires.] ➂ Release the tab and secure the wire. Note on a subwoofer connection: You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel when reproducing discrete signals.
m Connecting antennas ● ● Each antenna should be connected to the designated terminal(s) correctly, as shown in the following figure. Both AM and FM indoor antennas are included with this unit. In general, these antennas will provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality only with the indoor antennas, the use of an outdoor antenna may result in improvement.
GND terminal For maximum safety and minimum interference, connect the GND terminal to a good ground. A good ground is a metal stake driven into moist earth. English Connecting the indoor FM antenna Connect the included indoor antenna to the 75Ω UNBAL. FM ANT terminal. Note Do not use an outdoor FM antenna and the indoor FM antenna at the same time.
CONTROLS AND THEIR FUNCTIONS m Front panel 1 2 3 4 5 INPUT VOLUME DVD-LD/VCR/V-AUX/TAPE•MD/CD/TUNER/PHONO NATURAL SOUND AV RECEIVER RX–V10MK 6CH/2CH STANDBY/ON PTY SELECTOR PHONES SPEAKERS RDS MODE/FREQ EON A/B/C/D/E PRESET STATIONS TUNING KEY MODE 0 BASS TREBLE 0 0 I0 BALANCE EDIT ON OFF PTY SEEK FM/AM TUNING MODE MEMORY CENTER MODE PROGRAM – MODE START + – + L R AUTO/MAN’L MONO MAN’L/AUTO FM CINEMA DSP 6 78 9 0AB CDE FGH I J K L Parts in the shaded areas are
G PRESET STATIONS/TUNING button When an RDS station is received, pressing this button changes the display mode into the PS mode, PTY mode, RT mode, and frequency display in turn. This button is used for the PRESET STATIONS function when “PRESET” is illuminated on the display, and the TUNING function when “PRESET” is not illuminated. The following explains these functions in detail. 0 PTY SEEK MODE button Turns the unit into the PTY SEEK mode.
m Remote controller The remote controller provided with this unit is designed to control the most commonly used functions. If the CD player or tape deck is a YAMAHA component with remote control compatibility, this remote controller will also control various functions.
English 7 Input selector keys Press a key to select the input source. When the DVD/LD input source is selected, pressing the DVD/LD key switches the input signals between 2 channel stereo signals and 6 channel discrete signals. When switched to “6ch”, discrete signals from the unit connected to the DVD/LD 6CH DISCRT INPUT terminals of this unit are selected as the input signals.
m Display panel 1 2 3 MEMO PRESET AUTO PTY H PTY PS RT EON INFO SPORT NEWS AFFAIRS 7 89 4 5 6 ST FM MHz PRO LOGIC CONCERT MONO ROCK CONCERT NORMAL WIDE TEST ENHANCED VIDEO MOVIE CONCERT HALL PHANTOM < A B C 0 l00 SLEEP D Indicators in the shaded areas are provided for Europe and U.K. models only. 1 AUTO indicator This indicator will be illuminated during the automatic tuning mode.
This procedure lets you adjust the sound output level balance between the main, center, and rear speakers using the built-in test tone generator. After the adjustments, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor and the Dolby Pro Logic Surround decoder. The adjustment of each speaker output level should be done at your listening position with the remote controller.
8 INPUT VOLUME DVD-LD/VCR/V-AUX/TAPE•MD/CD/TUNER/PHONO NATURAL SOUND AV RECEIVER RX–V10MK 6CH/2CH – LEVEL + DELAY/CENTER /REAR/SWFR TEST EFFECT STANDBY/ON PROGRAM PROLOGIC V-AUX 0 PTY SELECTOR PHONES SPEAKERS RDS MODE/FREQ EON A/B/C/D/E PRESET STATIONS TUNING OFF PTY SEEK FM/AM TUNING MODE MEMORY CENTER MODE KEY MODE BASS TREBLE 0 0 DIR A DIR B REC/PAUSE START – + PLAY BALANCE A/B 7 TAPE PROGRAM – MODE DVD/LD 2CH/6CH VCR I0 EDIT ON ENHANCED ON/OFF + – + L
English INPUT VOLUME DVD-LD/VCR/V-AUX/TAPE•MD/CD/TUNER/PHONO NATURAL SOUND AV RECEIVER RX–V10MK 6CH/2CH 10 STANDBY/ON 0 PTY SELECTOR PHONES SPEAKERS RDS MODE/FREQ EON A/B/C/D/E PRESET STATIONS TUNING KEY MODE BASS TREBLE 0 0 – LEVEL + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC V-AUX I0 BALANCE DVD/LD 2CH/6CH VCR DIR A DIR B REC/PAUSE – + EFFECT ENHANCED ON/OFF PLAY EDIT ON OFF PTY SEEK FM/AM TUNING MODE MEMORY CENTER MODE A/B PROGRAM – MODE START + – +
From pages 24 to 39, this manual describes how to operate this unit mainly by using the front panel control parts. To operate this unit on the remote controller, use the corresponding keys on the remote controller.
m Recording a source to tape (or MD) In step 4, turn the INPUT selector on the front panel or press the DVD/LD (2CH/6CH) key on the remote controller repeatedly until “DVD 6ch” appears on the display. 1 2 INPUT VOLUME English To listen to a decoded source using Dolby Digital or DTS by reproducing the signals input to the DVD/LD 6CH DISCRT INPUT terminals of this unit.
m Sound control Adjusting the BALANCE control Adjusting the subwoofer output level Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused by speaker location or listening room conditions. If your audio system includes a subwoofer, and an amplifier driving the subwoofer (or a subwoofer system including an amplifier) is connected to the SUBWOOFER OUT terminal on the rear of this unit, you can adjust the subwoofer output level on this unit.
Quick automatic-search tuning (automatic tuning) is effective when the station signals are strong with no interference. However, manual tuning can be used during less-than-ideal conditions.
PRESET TUNING m Manual preset tuning This unit can store station frequencies selected by the tuning operation. With this function, you can recall any desired station only by selecting the preset station number. Up to 40 stations (8 stations x 5 groups) can be stored.
English m Automatic preset tuning You can make use of an automatic preset tuning function for FM stations. With this function, this unit performs automatic tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 28. * Only RDS stations can be stored by this function.
m Exchanging preset stations You can exchange the places of two preset stations with each other as shown below.
RECEIVING RDS STATIONS Europe and U.K. models only English In areas where RDS broadcasts cannot be received, the RDS broadcast functions do not operate. (Skip the procedures from pages 31 to 35.) RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal.
Program types in the PTY mode NEWS News: Short accounts of facts, events and publicly expressed views, reportage and actuality. AFFAIRS Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis. INFO Information: Program whose purpose is to impart advice in the widest sense, including meteorological reports and forecasts, consumer affairs, medical help, etc.
When an RDS station is received, “PS”, “PTY” and/or “RT” that correspond to the RDS data services employed by the station light up on the display. By pressing the RDS MODE/FREQ button once or more, you can change the display mode among the RDS modes employed by the received station in the order shown below. (The RDS mode not employed by the station cannot be selected.) Illumination of the indicator on the head of a name of RDS mode shows that the corresponding RDS mode is now selected.
m Selecting your desired program type from among preset RDS stations (PTY SEEK) By designating a program type, the unit automatically searches all preset stations for an RDS station which broadcasts a program of the program type. * There are 15 program types for classifying RDS stations. For details, refer to page 32.
English m Automatic selection of desired program when broadcasting starts This function uses the EON (Enhanced Other Networks) data service on the RDS station network. By only selecting a desired program type (NEWS, INFO, AFFAIRS or SPORT), this unit automatically searches all preset RDS stations for a station that broadcasts that program type (though you cannot check the searching process), and, if found, receives a program when its broadcast starts in place of the program now being received.
USING DIGITAL SOUND FIELD PROCESSOR (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room. You can create an excellent audio sound field by selecting a suitable sound field program (this will, of course, depend on what you will be listening to), and adding desired adjustments.
INPUT VOLUME DVD-LD/VCR/V-AUX/TAPE•MD/CD/TUNER/PHONO NATURAL SOUND AV RECEIVER RX–V10MK 6CH/2CH – STANDBY/ON 0 PTY SELECTOR PHONES SPEAKERS RDS MODE/FREQ EON A/B/C/D/E English m Playing a source with an effect of the digital sound field processor (DSP) PRESET STATIONS TUNING KEY MODE BASS TREBLE 0 I0 BALANCE 0 2 LEVEL + DELAY/CENTER /REAR/SWFR TEST PROGRAM PROLOGIC V-AUX DVD/LD 2CH/6CH VCR DIR A DIR B REC/PAUSE – + 2 EFFECT ENHANCED ON/OFF PLAY EDIT ON OFF PTY SEEK
Adjustment of the CENTER LEVEL You can adjust the sound output level of the center speaker even if the output level is already set in “SPEAKER BALANCE ADJUSTMENT” on page 21. 1 Press the DELAY/CENTER/REAR/SWFR key repeatedly until “CNTR” appears in the display. Notes ● This adjustment can be made only when the digital sound field program PRO LOGIC or PRO LOGIC ENHANCED is selected, or the “DVD/LD 6CH” input source mode is selected.
English Adjustment of DELAY TIME You can adjust the time difference between the beginning of the sound from the main speakers and the beginning of the effect sound from the rear speakers. The larger the value, the later the effect sound is generated. This adjustment can be made to all programs individually.
TROUBLESHOOTING Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. Problem Amplifier What to Do Power cord is not plugged in or is not completely inserted. Firmly plug in the power cord. This unit does not work normally.
AUDIO SECTION Minimum RMS Output Power per Channel MAIN L, R 8 ohms, 20 Hz to 20 kHz, 0.04% THD ...................................................45W+45W CENTER 8 ohms, 1 kHz, 0.04% THD ....................45W REAR L,R 8 ohms, 1 kHz, 0.3% THD............15W+15W Dynamic Power per Channel (by IHF Dynamic Headroom measuring method) 8 ohms..........................................65W+65W 6 ohms..........................................75W+75W 4 ohms..........................................95W+95W 2 ohms......
YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.