RX-V1900_U-cv.fm Page 1 Friday, June 20, 2008 11:23 AM U RX-V1900 RX-V1900 AV Receiver OWNER’S MANUAL © 2008 Yamaha Corporation All rights reserved. Black process 45.0° 240.
IMPORTANT SAFETY INSTRUCTIONS 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
d) 20 21 22 23 If the product does not operate normally by following the operating instructions.
Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.
Contents Features ................................................................... 3 Supplied accessories .................................................. 3 Notice ....................................................................... 4 Getting started ........................................................ 5 Quick start guide .................................................... 6 Using Bluetooth™ components............................
What you can do with MANUAL SETUP By configuring the parameters in “MANUAL SETUP”, you can adjust a variety of system settings suited for your listening environment. The following is a brief description of some of the useful menus you can configure in “MANUAL SETUP”. For more detailed information, see “Customizing this unit (MANUAL SETUP)” (page 74) and “SET MENU tree” (page 123).
FEATURES Features HDMI™ (High-Definition Multimedia Interface) ◆ Minimum RMS output power (20 Hz to 20 kHz, 0.04% THD, 8 Ω) Front: 130 W + 130 W Center: 130 W Surround: 130 W + 130 W Surround back: 130 W + 130 W ◆ HDMI interface for standard, enhanced or high-definition video as well as multi-channel digital audio based on HDMI version 1.3a (HDMI is licensed by HDMI Licensing, LLC.
NOTICE Notice About this manual • y indicates a tip for your operation. • Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses. • This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc.
GETTING STARTED Getting started 1 3 ■ VOLTAGE SELECTOR (Asia and General models only) Caution 2 1 Take off the battery compartment cover. 2 Insert the four supplied batteries (AAA, R03, UM-4) according to the polarity markings (+ and –) on the inside of the battery compartment. 3 The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local voltage BEFORE plugging the power cable into the AC wall outlet.
QUICK START GUIDE Quick start guide The following steps describe the easiest way to enjoy DVD movie playback in your home theater. Video monitor Front right speaker Front left speaker Preparation: Check the items Subwoofer Surround right speaker In these steps, you need the following supplied accessories. ❏ Power cable The following items are not included in the package of this unit.
Quick start guide Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Step 1: Set up your speakers Front speakers and center speaker Loosen HDMI VIDEO COMPONENT VIDEO MONITOR OUT BD/HD DVD A BD/HD DVD B DVD C CBL/SAT Y Y PB PB PR PR DVD CBL/SAT IN Insert INTRODUCTION Place your speakers in the room and connect them to this unit. Tighten ANTENNA DVR OUT IN VCR OUT MONITOR OUT FM 75Ω UNBAL.
Quick start guide Step 2: Connect your DVD player and other components DVD VIDEO 3 Connect the video cable to the VIDEO MONITOR OUT jack of this unit and the video input jack of your video monitor. VIDEO MONITOR OUT Video monitor HDMI VIDEO COMPONENT VIDEO MONITOR OUT BD/HD DVD A BD/HD DVD B DVD C CBL/SAT Y Y PB PB DVD CBL/SAT IN AV receiver ANTENNA DVR OUT IN VCR OUT MONITOR OUT FM 75Ω UNBAL.
Quick start guide Step 3: Turn on the power and start playback 6 To set this unit to the standby mode, press B MAIN ZONE ON/OFF. INTRODUCTION Check the type of the connected speakers. If the speakers are 6-ohm speakers, set “SPEAKER IMP.” to “6Ω MIN” before using this unit (page 26). You can also use 4-ohm speakers as the front speakers (page 102). 1 Turn on the video monitor connected to this unit. 2 Press A MASTER ON/OFF inward to the ON position on the front panel.
Connections Rear panel 1 2 HDMI 3 4 VIDEO COMPONENT VIDEO MONITOR OUT BD/HD DVD A BD/HD DVD B DVD C CBL/SAT Y 5 DVD CBL/SAT IN 6 7 ANTENNA DVR OUT IN VCR OUT MONITOR OUT Y FM 75Ω UNBAL.
Connections Placing speakers The speaker layout below shows the speaker setting we recommend. y • 7.1-channel speaker layout is highly recommended for playback of the high definition digital audio sources (Dolby TrueHD, DTS-HD Master Audio, etc.) with sound field programs. • We recommend that you add the presence speakers for the effect sounds of the CINEMA DSP sound field program. 7.1-channel speaker layout PREPARATION C FR FL FR 30˚ SW FL SBL C SL SR SL 60˚ 80˚ SL SR SBR SR SBL SBR 1.
Connections ■ Speaker types Front left and right speakers (FL and FR) The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same. Center speaker (C) The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a center speaker, you can do without it.
Connections Connecting speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, this unit cannot reproduce the input sources accurately. Caution Notes • A speaker cord is actually a pair of insulated cables running side by side. Cables are colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the “+” (red) terminals of this unit and your speaker.
Connections ■ 6.1-channel speaker connection Surround back speaker Presence speakers (page 12) or Zone 2/Zone 3 speakers (page 99) Subwoofer SPEAKERS SP1 R PRESENCE/ZONE 2/ZONE 3 R SURROUND BACK/ BI-AMP + + R + SUB WOOFER Center speaker L + L SINGLE CENTER + + SP2 L SURROUND + ZONE 2/ZONE 3 L R PRE OUT + R + L FRONT + Zone 2/Zone 3 speakers (page 99) Left Right Surround speakers Left Right Front speakers ■ 5.
Connections ■ Connecting the speaker cable 1 Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits. ■ Connecting the banana plug (Except U.K., Europe, Asia and Korea models) Tighten the knob using the supplied speaker terminal wrench and then insert the banana plug into the end of the terminal. 10 mm (0.
Connections Information on jacks and cable plugs This unit has three types of audio jacks, three types of video jacks and HDMI jacks. You can choose the connection method depending on the component to be connected.
Connections Information on HDMI™ This unit has four HDMI input jacks and one HDMI output jack for digital audio and video signal input/output. ■ HDMI jack and cable plug • Refer to the instruction manuals of the input source component, and set the component appropriately. HDMI Notes HDMI cable plug • We recommend that you use a commercially available HDMI cable shorter than 5 meters (16 feet) with the HDMI logo printed on it.
Connections Audio and video signal flow ■ Audio signal flow Input ■ Video signal flow Input Output Output HDMI HDMI DIGITAL AUDIO (COAXIAL) COMPONENT VIDEO DIGITAL AUDIO (OPTICAL) S VIDEO AUDIO VIDEO Digital Analog Note Only the HDMI input jacks support DSD, Dolby TrueHD, Dolby Digital Plus, DTS-HD Master Audio and DTS-HD High Resolution Audio signal inputs.
Connections Connecting a TV monitor or projector y Make sure that this unit and other components are unplugged from the AC wall outlets. To select the types of the audio signals output at the HDMI OUT jack, configure the “HDMI AUDIO” setting (page 80). Note HDMI PREPARATION If you turn off the video monitor connected to the HDMI OUT jack via a DVI connection, the connection may fail. In this case, the HDMI indicator flashes irregularly.
Connections Connecting other components ■ Connecting audio and video components This unit has three types of audio jacks, three types of video jacks and HDMI jacks. You can choose the connection method depending on the component to be connected. y HDMI can transmit both digital audio and video over a single HDMI cable.
Connections Jacks used for audio and video connections Recommended connections are indicated by boldface. When connecting a recording component, you need to make additional connections for recording (signal transmission from this unit to the recording component). Make sure that this unit and other components are unplugged from the AC wall outlets. y PREPARATION You can also use the VIDEO AUX jacks (page 24) on the front panel to connect an additional component.
Connections Jacks to connect Component Signal type On component VCR CD player MD or CD recorder Turntable On this unit Audio Audio out (analog) AUDIO (VCR IN) Video S-video out S VIDEO (VCR IN) Video out (composite) VIDEO (VCR IN) Audio recording Audio in (analog) AUDIO (VCR OUT) Video recording S-video in S VIDEO (VCR OUT) Video in (composite) VIDEO (VCR OUT) Coaxial out COAXIAL (CD) Audio out (analog) AUDIO (CD) Audio Audio out (analog) AUDIO (MD/CD-R IN) Audio recording Op
Connections [4] SUR.BACK/PRESENCE PRE OUT jacks Surround back or presence channel output jacks. When you only connect one external amplifier for the surround back channel, connect it to the SINGLE (SB) jack. y • To output surround back channel signals at these jacks, set “PRESENCE SP“ to “NONE” and “SUR.B L/R SP” to any parameter except “NONE” (page 76). • To output presence channel signals at these jacks, set “PRESENCE SP“ to “YES” and “SUR.B L/R SP” to “NONE” (page 76).
Connections Using the VIDEO AUX jacks on the front panel Use the VIDEO AUX jacks on the front panel to connect a game console or a video camera to this unit. To reproduce the source signals input at these jacks, select “V-AUX” as the input source. Connecting the FM and AM antennas Both FM and AM indoor antennas are supplied with this unit. In general, these antennas should provide sufficient signal strength.
Connections Assembling the supplied AM loop antenna Connecting the power cable ■ Connecting the AC power cable Plug the supplied AC power cable into the AC inlet after all other connections are complete, then plug the AC power cable into an AC wall outlet. AC IN To the AC wall outlet AC OUTLETS Connecting the wire of the AM loop antenna Press and hold Insert Release PREPARATION (U.S.A.
Connections Setting the speaker impedance Caution If you are to use 6 ohm speakers, set “SPEAKER IMP.” to “6Ω MIN” as follows BEFORE using this unit. You can also use 4 ohm speakers as the front speakers (page 102). 1 Make sure this unit is turned off. 2 Press and hold O STRAIGHT on the front panel and then press A MASTER ON/OFF inward to the ON position. This unit turns on, and the advanced setup menu appears in the front panel display.
Connections Front panel display a b c d e f DOCK neural V-AUX VCR DVR CBL/SAT DVD BD/HD DVD MD/CD-R TV i j SILENT CINEMA 3 VIRTUAL ADAPTIVE DRC ENHANCER DISCRETE MATRIX q DIGITAL PLUS HD 96 24 q PL x q EX q TRUE HD MASTER AUDIO TUNER XM SIRIUS dB VOLUME L C R SLEEP ZONE2 SL LFE F SR ZONE3 SBL SB SBR h n k l m o HD TUNED STEREO AUTO MEMORY CATEGORY ALL HOLD q dB VOLUME L C R SLEEP ZONE2 SL LFE SR ZONE3 SBL SB SBR r p s a CSII indicator (U.S.A.
Connections Using the remote control Note The HD indicator is only applicable to the U.S.A. model only and lights up when this unit is turned into the HD Radio reception band. The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. o Menu browsing indicator Lights up if any items exist under the current item during menu browsing for iPod, etc.
Connections Operation mode selector (E) The function of some buttons depends on the operation mode selector position. AMP Operates the amplifier function of this unit. SOURCE Operates the component selected with an input selector button (page 90). PREPARATION TV Operates the TV (page 89). Notes • Do not spill water or other liquids on the remote control. • Do not drop the remote control.
Optimizing the speaker setting for your listening room This unit employs the YPAO (Yamaha Parametric room Acoustic Optimizer) technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening environment.
Optimizing the speaker setting for your listening room y Press 8ENTER to display the result. AUTO SETUP . RESULT MLT : 1 SP : 5/4/0.1 DIST: 14.0/17.0ft LVL : -10.0/+5.0dB >SET CANCEL [ ]/[ ]: Up/Down [ENTER]: Detail Check if “START” is selected and then press 8ENTER. [ 2 4 AUTO SETUP p It is recommended that you use a tripod (etc.) to affix the optimizer microphone at the same height as your ears would be when you are seated in your listening position.
Optimizing the speaker setting for your listening room 7 Press 8ENTER to return to the top result display. AUTO SETUP RESULT MLT : 1 SP : 5/4/0.1 DIST: 14.0/17.0ft LVL : -10.0/+5.0dB . >SET CANCEL [ ]/[ ]: Up/Down [ENTER]: Enter [ Number of the measured points Results of the speaker connection and wiring 8 Press 8 l / h to select “SET” or “CANCEL” and then press 8ENTER. AUTO SETUP Results of the speaker distance from the listening position [ RESULT MLT : 1 SP : 5/4/0.1 DIST: 14.0/17.0ft LVL : -10.
Optimizing the speaker setting for your listening room ignore the error and carry on the measurement. However, we recommend that you solve the problem before starting the measurement. Advanced automatic setup • If “E-10:INTERNAL ERROR” appears, you can select only “EXIT”. • For details about each error message, see “AUTO SETUP” (page 113). If you have done all the preparations necessary, follow the procedure below to optimize the setup of this unit for multiple listening positions.
Optimizing the speaker setting for your listening room Before proceeding next operation Once you perform the next operation, this unit starts the automatic setup procedure in 10 seconds. For more accurate measurements, we recommended that you get out of the room or move to the wall where speakers are not around during the measurement. 4 Press 8ENTER to start the measurement. Loud test tones are output from each speaker during the measurement.
Playback Caution Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS. 3 Start playback on the selected source component or select a broadcast station.
Playback Selecting audio input jacks (AUDIO SELECT) Selecting the multi-channel input component Use this feature (audio input jack select) to switch the input jack assigned to an input source when more than one jacks are assigned to an input source. 1 2 Rotate the C INPUT selector (or press one of the input selector buttons (3)) to select the desired input source. VCR DVR CBL/SAT DVD BD/HD DVD A.
Playback Muting the audio output Press K MUTE on the remote control to mute the audio output. Press K MUTE again to resume the audio output. y ■ Audio information FORMAT Signal format. When this unit cannot detect a digital signal, it automatically switches to analog input. SAMPLING The number of samples per second taken from a continuous signal to make a discrete signal. CHANNEL The number of source channels in the input signal (front/surround/LFE).
Playback Before performing the following operations, set the operation mode selector on the remote control to E AMP. Using the sleep timer Use this feature to automatically set the main zone to the standby mode after a certain amount of time. The sleep timer is useful when you are going to sleep while this unit is playing or recording a source. The sleep timer also automatically turns off any external components connected to the AC OUTLET(S) (page 25).
Sound field programs This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from almost any stereo or multi-channel sound source. This unit is also equipped with a Yamaha digital sound field processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Sound field programs Descriptions of the characteristics of the sound field programs Following indexes indicates the characteristics and trends of each sound field program. Note The characteristics of the sound field programs may differ depending on the settings of the listening room, etc. Size of sound field space (Size) Small Sound field atmosphere (Atmosphere) Large Simple Complex Indicates the size of the sound field to be generated.
Sound field programs Hall in Amsterdam The large, shoe box shaped hall seats about 2200 around the circle stage. Reflections are rich and pleasing while the sound travels freely. Size Small Large V/H balance Vertical Horizontal Atmosphere Simple Complex Size Small Church in Freiburg Located in the south of Germany, this grand, stone-built church has a pointed tower at 120 meters in height.
Sound field programs ■ For various sources ENTERTAIN 3 ENTERTAIN Sports This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live feeling. In sports broadcasts, the voices of the commentator and sportscaster are positioned clearly on the center while the atmosphere of the stadium expands in an optimum space to offer the listeners with a feeling of presence in the stadium.
Sound field programs ■ For movie sources y You can select the desired decoder (page 66) used with following sound field program (except “Mono Movie”). MOVIE 4 MOVIE Standard This program create a sound field emphasizing the surrounding feeling without disturbing the original acoustic positioning of multi-channel audio such as Dolby Digital and DTS.
Sound field programs ■ Stereo playback STEREO 5 STEREO 2ch Stereo Use this program to mix down multi-channel sources to 2 channels. 7ch Stereo Use this program to output sound from all speakers. When you play back multi-channel sources, this unit downmixes the source to 2 channels, and then output the sound from all speakers. This program creates a larger sound field and is ideal for background music at parties, etc.
Sound field programs Before performing the following operation, set the operation mode selector on the remote control to E AMP. Before performing the following operation, set the operation mode selector on the remote control to E AMP. Using CINEMA DSP 3D mode Enjoying unprocessed input sources CINEMA DSP 3D mode creates the intensive and accurate stereoscopic sound field in the listening room. You can activate and deactivate the CINEMA DSP 3D mode.
Using audio features Before performing the following operation, set the operation mode selector on the remote control to E AMP. Before performing the following operation, set the operation mode selector on the remote control to E AMP. Enjoying pure hi-fi sound Adjusting the speaker level Use the Pure Direct mode to enjoy the pure fidelity sound of the selected source. When the Pure Direct mode is activated, this unit plays back the selected source with the least circuitry.
FM/AM tuning Overview Note If the signal from the station you want to select is weak, search the station manually or enter the frequency directly (page 47). You can use two tuning modes to tune into the desired FM/AM station: Frequency tuning mode You can search or specify the frequency of the desired FM/AM station automatically or manually (see “FM/AM tuning operations” on this page).
FM/AM tuning Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3TUNER. • (U.S.A. model only) When this unit stores the FM HD Radio stations with this feature, this unit stores only the main audio program of the stations (HD1). When you want to store the sub-audio programs of the FM HD Radio stations, preset the stations manually.
FM/AM tuning y • You can also select a preset number (1 to 8) by pressing the numeric buttons (A). • If you select a preset number being used ("*" appears next to the preset number), the current preset station will be overwritten. 4 Press FENTER (or 8ENTER). The preset station is set and the PRESET indicator disappears. • (U.S.A.
Using HD Radio™ features (U.S.A. model only) HD Radio technology is a new technology that enables FM and AM radio stations to broadcast programs digitally. Digital broadcasting provides listeners with radically improved audio quality and reception as well as new data services. Furthermore, supplemental program services allow listeners to select from up to 8 HD Radio programs multicast on a single FM HD Radio channel. For further information on HD Radio technology, visit “http://www.ibiquity.com/”.
Using HD Radio™ features (U.S.A. model only) Displaying HD Radio™ information Use this feature to display the HD Radio information in the front panel display or in the OSD. INPUT INFO Input source y • You can configure the display settings with “DISPLAY SET” (page 83). • To hold or release the displayed information, set the operation mode selector to ESOURCE and then press 8ENTER. While it is held, the HOLD indicator flashes in the front panel.
XM® Satellite Radio tuning XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk and entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan. XM Satellite Radio online information For U.S. customers: http://www.xmradio.com/ For Canadian customers: http://www.xmradio.
XM® Satellite Radio tuning Activating XM Satellite Radio Once you have installed the XM Mini-Tuner Home Dock, inserted the XM Mini-Tuner, connected the XM MiniTuner Home Dock to your XM Ready® home audio system, and installed the antenna, you are ready to subscribe and begin receiving XM programming. There are three places to find your eight character XM Radio ID: On the XM Mini-Tuner, on the XM Mini-Tuner package, and on XM Channel 0. Record the XM Radio ID in the following eight squares for reference.
XM® Satellite Radio tuning 2 Press GPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to search for a channel within all channels. Press GPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to change the preset channel number (1 to 8). y y You can search for a channel quickly by pressing and holding GPRESET/TUNING/CH l / h (or 8PRESET/CH k / n). ■ Category Search mode 1 Press ISEARCH MODE (or HSRCH MODE) repeatedly to select “CAT SEARCH”. 2 Press KCATEGORY (or 8A-E/CAT.
XM® Satellite Radio tuning y Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3XM. Setting the XM Satellite Radio preset channels You can use this feature to store up to 40 XM Satellite Radio channels (A1 to E8: 8 preset channel numbers in each of the 5 preset channel groups). You can then recall any preset channel easily by selecting the preset channel group and number as described in “Preset Search mode” (page 54).
XM® Satellite Radio tuning Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3XM. Back to “CATEGORY INFO” y Displaying the XM Satellite Radio information Use this feature to display the XM Satellite Radio information in the front panel display or in the OSD. y • You can configure the display settings with “DISPLAY SET” (page 83). • You can hold or release the displayed information by pressing 8ENTER.
SIRIUS Satellite Radio™ tuning SIRIUS Satellite Radio provides over 130 channels of exclusive entertainment and 100% commercial-free music. Only SIRIUS has more than 65 original music channels, from today’s hits to R&B, oldies, and classical masterpieces. From authentic country and real bluegrass to cool jazz, hot latin, reggae, rock and many more. Best of all, it’s all 100% commercial-free. SIRIUS also has more than 55 channels of world-class sports, news and entertainment.
SIRIUS Satellite Radio™ tuning Activating SIRIUS Satellite Radio™ subscription Before using the SIRIUS Satellite Radio feature, you need to activate your SIRIUS Satellite Radio subscription. To activate the subscription you need the Sirius ID which is uniquely assigned to the SiriusConnect tuner. Sirius ID is 12-digit number and it appears on the package of the SiriusConnect tuner, on the label of the SiriusConnect tuner, and when you tune into the SIRIUS Satellite Radio channel “0” (see below).
SIRIUS Satellite Radio™ tuning ■ All Channel Search mode 1 Press ISEARCH MODE (or HSRCH MODE) repeatedly to select “ALL CH SEARCH”. 2 Press GPRESET/TUNING/CH l / h (or 8PRESET/CH k / n) repeatedly to search for a channel within all channels. y • You can search for a channel quickly by pressing and holding GPRESET/TUNING/CH l / h (or 8PRESET/CH k / n). • You can skip channels to the previous or next category by pressing KCATEGORY (or 8A-E/CAT. l / h).
SIRIUS Satellite Radio™ tuning y Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3SIRIUS. Setting the SIRIUS Satellite Radio™ preset channels You can use this feature to store up to 40 SIRIUS Satellite Radio channels (A1 to E8: 8 preset channel numbers in each of the 5 preset channel groups).
SIRIUS Satellite Radio™ tuning Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3SIRIUS. 5 Setting the Parental Lock You can use the Parental Lock feature to limit the access to the desired SIRIUS Satellite channels. This unit automatically skips the locked channels when this unit is in the All Channel Search mode or Category Search mode and you search a channel by pressing GPRESET/ TUNING/CH l / h (or 8PRESET/CH k / n).
SIRIUS Satellite Radio™ tuning Before performing the following operations, set the operation mode selector on the remote control to ESOURCE and then press 3SIRIUS. INPUT INFO Input source, channel number, channel name Displaying the SIRIUS Satellite Radio™ information Use this feature to display the SIRIUS Satellite Radio information in the front panel display or in the OSD. y • You can configure the display settings with “DISPLAY SET” (page 83).
Using iPod™ Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-11, sold separately) connected to the DOCK terminal of this unit (page 23), you can enjoy playback of your iPod using the supplied remote control. You can also use the Compressed Music Enhancer mode of this unit to enhance the sound quality of the compression artifacts (such as the MP3 format) stored on your iPod (page 44).
Using iPod™ 2 Press 8k / n to select “Music”, “ Videos” or “Settings” and then press 8h. • To browse the music contents stored on your iPod, select “Music”. • To browse the video contents stored on your iPod, select “Videos”. • To change the playback settings of your iPod, select “Settings”. Note “Videos” does not appear unless both your iPod and Yamaha iPod universal dock support the video browsing feature.
Using Bluetooth™ components You can connect a Yamaha Bluetooth receiver (such as YBA-10, sold separately) to the DOCK terminal of this unit and enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth wireless audio receiver and your Bluetooth component in advance.
Advanced sound configurations Selecting decoders PLIIx Game PLII Game ■ Selecting decoders for 2-channel sources (surround decode mode) Use this feature to play back sources with selected decoders. You can play back 2-channel sources on multichannels. Set the operation mode selector to E AMP and then press Q SUR. DECODE repeatedly on the remote control to select the surround decode mode.
Advanced sound configurations ■ Selecting decoders for multi-channel sources If you connected surround back speakers, use this feature to enjoy 6.1/7.1-channel playback for multi-channel sources using the Dolby Pro Logic IIx, Dolby Digital EX, DTS-ES, or Neural-THX decoders. Set the operation mode selector to EAMP and then press LEXTD SUR. on the remote control repeatedly to switch between 5.1 and 6.1/7.1channel playback.
Advanced sound configurations y • Repeat steps 3 and 4 as necessary to change other sound field program parameter settings. • The available parameters for some of the sound field programs may be displayed on more than one page in the OSD. In this case, press 8 k / n to scroll through pages. • When you set a sound field parameter to a value other than the initial factory settings, an asterisk mark (*) appears by the parameter name in the OSD.
Advanced sound configurations ■ Sound field parameter descriptions Use the following sound field parameters to customize the sound field programs in detail. y To change sound field parameter settings, see page 67 for details. Sound field parameter INIT.DLY P.INIT.DLY S.INIT.DLY SB INIT.DLY Features Initial delay. Presence, surround, and surround back sound field initial delay.
Advanced sound configurations Sound field parameter LIVENESS S.LIVENESS SB LIVENESS Features Liveness. Surround and surround back liveness. Adjusts the reflectivity of the virtual walls in the hall by changing the rate at which the early reflections decay. The early reflections of a sound source decay much faster in a room with acoustically absorbent wall surfaces than in one which has highly reflective surfaces.
Advanced sound configurations Sound field parameter REV.DELAY Features Reverberation delay. Adjusts the time difference between the beginning of the direct sound and the beginning of the reverberation sound. The larger the value, the later the reverberation sound begins. A later reverberation sound makes you feel as if you are in a larger acoustic environment. Level Control range: 0 to 250 ms Source sound (dB) 60 dB Reverberation Time REV.DELAY REV.LEVEL REV.TIME Reverberation level.
Advanced sound configurations Sound field parameter EFFECT LEVEL (“Straight Enhancer” and “7ch Enhancer” only) Features Straight and 7-channel Compressed Music Enhancer effect level. The high-frequency signals of some sources may be emphasized too much. In this case, set the effect level to “LOW”. Choices: HIGH, LOW • Select “HIGH” for a high effect level. • Select “LOW” for a low effect level. SUR (MOVIE sound field programs (except “Mono Movie”) and “SUR. DECODE” only) 72 En Decoder type.
Advanced sound configurations ■ Decoder parameter descriptions Use the following decoder parameters to customize the specific decoders in detail. Decoder parameter PANORAMA (“PLIIx Music” and “PLII Music” only) Features Pro Logic IIx Music and Pro Logic II Music panorama. Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. Choices: OFF, ON CENTER WIDTH (“PLIIx Music” and “PLII Music” only) Pro Logic IIx Music and Pro Logic II Music center width.
Customizing this unit (MANUAL SETUP) The “MANUAL SETUP” menu allows you to manually adjust speaker and system parameters using the remote control. For the complete menu structure, see “SET MENU tree” (page 123). y The initial factory settings are indicated in bold under each parameter. Operating the MANUAL SETUP menu 4 This section explains how to configure parameters in the MANUAL SETUP menu using the OSD. Press 8 k / n repeatedly and then press 8 ENTER to select and enter the desired submenu.
Customizing this unit (MANUAL SETUP) 1 SPEAKER MENU Use this feature to manually adjust the basic speaker settings. Most of the “SPEAKER MENU” parameters are set automatically when you run the automatic setup. Front speakers FRONT SP y • Set “TEST TONE” to “ON” (page 77) to output the test tone for the “CONFIG”, “LEVEL” and “DISTANCE” settings.
Customizing this unit (MANUAL SETUP) Surround back left/right speakers SUR.B L/R SP Choice Descriptions LRGx1 Select this setting when the single surround back speaker is large. LRGx2 Select this setting when the surround back left and right speakers are large. SMLx1 Select this setting when the single surround back speaker is small. SMLx2 Select this setting when the surround back left and right speakers are small. NONE Select this setting when you do not use the surround back speakers.
Customizing this unit (MANUAL SETUP) Adjusted speaker FRONT L Front left speaker FRONT R Front right speaker CENTER Center speaker SUR. L Surround left speaker SUR. R Surround right speaker SB L Surround back left speaker SB R Surround back right speaker SWFR Subwoofer PRNS L Presence left speaker PRNS R Presence right speaker Use this menu to manually adjust the various volume settings.
Customizing this unit (MANUAL SETUP) Muting type MUTING TYPE Use this feature to adjust how much the mute function reduces the output volume (page 37). Choice Functions FULL Mutes all the audio output. –20dB Reduces the current volume by 20 dB. Maximum volume MAX VOL. Use this feature to set the maximum volume level in the main zone. This feature is useful to avoid the unexpected loud sound by mistake. For example, the original volume range is –80.0 dB to +16.5 dB. However, when “MAX VOL.
Customizing this unit (MANUAL SETUP) Parametric equalizer select PEQ SELECT Use this feature to select the parametric equalizer type that applied to the results of the automatic setup. Choice Choice MIN/AUTO • MIN: Adjusts the dynamic range to narrow when this unit is decoding bitstream signals (except Dolby TrueHD). • AUTO: Adjusts the dynamic range according to the instruction of the input source signals when this unit is decoding Dolby TrueHD signals. STD Adjusts the dynamic range to medium.
Customizing this unit (MANUAL SETUP) ■ Audio settings E)AUDIO SET Tone bypass TONE BYPASS Use this feature to select whether the audio output bypasses the tone control circuitry when “TREBLE” and “BASS” are set to 0 dB (page 46). Choice Functions AUTO Automatically bypasses the tone control circuitry to provide the purest signal possible when “TREBLE” and “BASS” are set to 0 dB. OFF Does not bypass the tone control circuitry.
Customizing this unit (MANUAL SETUP) 5 INPUT MENU Notes • The “COMPONENT I/P” parameter appears only when you set “VIDEO CONV.” to “ON”. • If your video monitor does not support analog video signals with 480p/576p of resolution, the SET MENU items may not be displayed on your video monitor when “COMPONENT I/P” is set to “ON”. HDMI resolution HDMI RES.
Customizing this unit (MANUAL SETUP) Input/output assignment I/O ASSIGNMENT Use this feature to assign the input/output jacks according to the component to be used if the initial settings of this unit do not correspond to your needs. Change the parameter to reassign the respective jacks and effectively connect more components. Once the input/output jacks are reassigned, you can select the corresponding component by using the C INPUT selector (or the input selector buttons (3)).
Customizing this unit (MANUAL SETUP) 3 Select the Bluetooth receiver in the Bluetooth device list and then enter the pass key “0000” on the Bluetooth component. Once this unit completes the pairing successfully, “Completed” appears. To cancel the pairing, press 9RETURN. Press 9RETURN to exit from “START PAIRING”. Notes • If the connected Bluetooth receiver cannot find any Bluetooth components, “Not found” appears. • If a Bluetooth receiver is not connected to this unit, “No Bluetooth receiver” appears.
Customizing this unit (MANUAL SETUP) Short message display SHORT MESSAGE Use this feature to activate or deactivate the short message display function. Choice Functions ON Activates the short message display function. The contents of the front panel display appear at the bottom of the screen each time you operate this unit. OFF Deactivates the short message display function.
Customizing this unit (MANUAL SETUP) Extended surround EXTD SUR. Use this feature to designate the extended decoder mode (page 67) for the input sources connected to the DIGITAL INPUT jacks when you turn on the power of this unit. Choice Functions AUTO Automatically detects the digital audio input signals and activates the appropriate decoder. LAST Automatically selects the decoder mode selected last time. ■ Zone set D)ZONE SET Use this feature to set the items related in Zone 2 or Zone 3.
Saving and recalling the system settings (SYSTEM MEMORY) Use this feature to save up to six of your favorite settings that can be easily recalled when needed. You can save the following system setting parameters: Saved parameters Page “SPEAKER MENU” parameters (except “TEST TONE”) 75 “VOLUME MENU” parameters (except “INIT. VOL.
Saving and recalling the system settings (SYSTEM MEMORY) 6 Press H MENU to exit from “SET MENU”. SYSTEM MEMORY . LOAD;;;;;;;CURRENT Church in Freiburg ADAPTIVE DRC;;AUTO EQUALIZER;;;;;;PEQ PEQ TYPE;;;NATURAL Loading the system settings [p]/[[]: Select [ENTER]: Return Note If you load the system settings, the settings currently configured are overwritten. If you do not want to erase the current settings, save the settings using the SYSTEM MEMORY feature in advance.
Saving and recalling the system settings (SYSTEM MEMORY) ■ Example 2: Switching the settings for different room environments Using examples ■ Example 1: Comparing the results of the automatic setup and manual setup This unit is equipped with three types of parametric equalizer settings (page 79), and you can also make your customized configuration of the sound settings of this unit by using the “MANUAL SETUP” parameters (see page 74).
Remote control features In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code for each input source (page 91). Controlling this unit, a TV, or other components ■ Controlling this unit Set the operation mode selector to E AMP to control this unit.
Remote control features ■ Controlling other components Set the operation mode selector to E SOURCE to control other components selected with the input selector buttons (3) or A . You must set the appropriate remote control code for each input source in advance (page 91). The following table shows the function of each control button used to control other components assigned to each input selector button (3) or A . Be advised that some buttons may not correctly operate the selected component.
Remote control features ■ Selecting a component to be controlled You can select a component to be controlled independently of the input source selected with the input selector buttons (3). Press 5 SELECT l / h repeatedly to select the desired component. The name of the component to be controlled appears in the display window (4) on the remote control. DVD Setting remote control codes You can control other components by setting the appropriate remote control codes. Codes can be set up for each input area.
Remote control features 3 Press FSETUP using a ballpoint pen or similar object. “SETUP” appears in the display window (4) on the remote control. 9 Press F SETUP again to exit from the “SETUP” mode. 10 Press 2 AV POWER or 0 p to confirm whether you can control your component using the remote control. SETUP y Note In the “SETUP” menu, complete each of the operations within 30 seconds. Otherwise, the remote control automatically exits from the “SETUP” menu.
Remote control features Programming codes from other remote controls Place this remote control about 5 to 10 cm (2 to 4 in) apart from the other remote control on a flat surface so that their infrared transmitters are aimed at each other and then press 8ENTER. “L–KEY” appears in the display window (4).
Remote control features 7 Press F SETUP again to exit the setup menu. 5 Edit the name of the control area. To locate the position to edit , press 8l / h. To select a character, press 8k / n. Notes • “ERROR” appears in the display window (4) on the remote control if you press a button not indicated in the respective step, or when you press more than one button simultaneously. • This remote control can learn approximately 200 functions.
Remote control features Macro programming features The macro programming feature makes it possible to perform a series of operations with the press of a single button. For example, when you want to play a CD, normally you would turn on the components, select the CD input, and press the play button to start playback. The macro programming feature lets you perform all of these operations simply by pressing the CD macro button. The buttons listed as macro buttons below are factory set with macro programs.
Remote control features ■ Programming macro operations You can program your own macro to transmit several remote control commands in sequence at the press of a button. Be sure to set up remote control codes or perform learning operations before programming the macro. 4 Press the buttons for the functions you want to include in the macro operation in sequence.
Remote control features Clearing configurations 4 You can clear all changes made in each function set, such as learned functions, macros, renamed control area names and setup remote control ID. ■ Clearing function sets 1 Press FSETUP using a ballpoint pen or similar object. “SETUP” appears in the display window (4). 2 Press 8k / n repeatedly to select “CLEAR” and then press 8ENTER. 3 Press 8k / n repeatedly to select the desired clear mode. Clear mode L:DVD (etc.
Remote control features Simplified remote control Use the supplied simplified remote control to make basic controls of this unit. STANDBY Sets the selected zone to the standby mode. ☞ P. 26, 100 SYSTEM MEMORY Save or recall the system settings. ☞ P. 86 STANDBY POWER POWER Turn on the power. ☞ P. 26, 100 SYSTEM MEMORY 1 2 3 4 INPUTl / h Select the input source. ☞ P. 35 INPUT PRESET +/– Recall the preset FM/AM stations, XM channels or SIRIUS channels. ☞ P.
Using multi-zone configuration This unit allows you to configure a multi-zone audio system. The multi-zone configuration feature enables you to set this unit to reproduce separate input sources in the main zone, second zone (Zone 2) and third zone (Zone 3). You can control this unit from the second or third zone using the supplied remote control. Only analog signals are sent to the second and third zones.
Using multi-zone configuration ■ Using the internal amplifiers of this unit Important safety notice The SP1 or SP2 speaker terminals of this Receiver should not be connected to a Passive Loudspeaker Selector Box or more than one loudspeaker per channel. Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Using multi-zone configuration 2 Press EPOWER to turn on the selected zone. 3 Perform the desired operation in the selected zone (page 101). y To turn off the desired zone, press CSTANDBY. ■ Selecting the input source of Zone 2 or Zone 3 Rotate the CINPUT selector (or set the operation mode selector to EAMP and then press one of the input selector buttons (3)). • Select “TUNER” as the input source to use the FM/AM tuning features (page 47) in the selected zone.
Advanced setup This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. Notes • Only A MASTER ON/OFF, O STRAIGHT and the N PROGRAM selector are effective while you are using the advanced setup menu.
Advanced setup ■ Parameter initialization INITIALIZE Press FID repeatedly using a ballpoint pen or similar object on the remote control to select the desired remote control ID. Each time you press FID, the remote control ID indicator changes as shown below. ID1 ID Use this feature to reset the parameters of this unit to the initial factory settings. You can select the category of parameters to be initialized.
TROUBLESHOOTING Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General Problem This unit fails to turn on or enters the standby mode soon after the power is turned on. No sound.
Troubleshooting Problem No picture. Cause Remedy See page The output and input for the picture are connected to different types of video jacks. Set “VIDEO CONV.” to “ON” or connect your source components in the same way as you connect your video monitor to this unit. 80 1080p-resolution analog video signals are only output at the COMPONENT VIDEO MONITOR OUT jacks. Connect your video monitor to the COMPONENT VIDEO MONITOR jacks.
Troubleshooting Problem No sound is heard from the surround speakers. No sound is heard from the subwoofer. Cause Remedy See page “SUR. L/R SP” in “CONFIG” is set to “NONE”. Set “SUR. L/R SP” to “SMALL” or “LARGE”. 75 This unit is in the “STRAIGHT” mode and a monaural source is being played back. Press O STRAIGHT to turn off the “STRAIGHT” mode. 45 The surround speakers are connected to the SURROUND BACK speaker terminals. Connect the surround speakers to the SURROUND speaker terminals.
Troubleshooting See page Problem Cause Remedy An audio source cannot be recorded by the digital recording component connected to the DIGITAL OUTPUT jacks. The audio source component is not connected to the DIGITAL INPUT jacks. Connect the audio source component to the DIGITAL INPUT jacks. 21 You are trying to record an audio source input at the DOCK terminal by the digital recording component connected to the DIGITAL OUTPUT jacks.
Troubleshooting ■ HDMI Problem No picture or sound. Cause Remedy See page The number of the connected HDMI components is over the limit. Reduce the number of the connected HDMI components. — HDCP authentication failed. Check that the connected HDMI components support the HDCP copy protection standards. — ■ Tuner (FM/AM) Problem Cause FM stereo reception is noisy.
Troubleshooting ■ XM Satellite Radio If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display. In this case, read the cause and follow the corresponding remedies. Status message Cause Remedy See page The XM Mini-Tuner is not installed in the XM Mini-Tuner Home Dock or the is not connected to this unit. Confirm the XM Mini-Tuner is fully seated in the dock and check the XM Mini-Tuner Home Dock cable is connected to this unit.
Troubleshooting ■ SIRIUS Satellite Radio If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display. In this case, read the cause and follow the corresponding remedies. Status message Cause Remedy See page ANTENNA ERROR The antenna is not connected to the SiriusConnect tuner properly. Check the connection of the antenna and SiriusConnect tuner.
Troubleshooting ■ Remote control Problem The remote control does not work or function properly. The remote control does not learn new functions. Cause Remedy See page Wrong distance or angle. The remote control will function within a maximum range of 6 m (20 ft) and no more than 30 degrees offaxis from the front panel. 28 Direct sunlight or lighting (from an inverter type of fluorescent lamp, etc.) is striking the remote control sensor of this unit. Reposition this unit.
Troubleshooting ■ iPod Note In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection of your iPod (page 23). Status message Loading... Cause Remedy See page This unit is in the middle of recognizing the connection with your iPod. This unit is in the middle of acquiring song lists from your iPod. Connect error There is a problem with the signal path from your iPod to this unit.
Troubleshooting ■ AUTO SETUP Before AUTO SETUP Error message Cause Remedy See page Connect MIC! Optimizer microphone is not connected. Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. 30 Unplug HP! Headphones are connected. Unplug the headphones. — Memory Guard! The parameters of this unit are protected. Set “MEMORY GUARD” to “OFF”. 84 During AUTO SETUP Error message Cause Remedy See page E-1:NO FRONT SP Front L/R channel signals are not detected.
Troubleshooting After AUTO SETUP Warning message Cause Remedy W-1:OUT OF PHASE Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. Check the speaker connections for proper polarity (+ or –). 13 W-2:OVER 24m (80ft) The distance between the speaker and the listening position is over 24 m (80 ft). Bring the speaker closer to the listening position.
RESETTING THE SYSTEM Resetting the system Use this feature to reset all the parameters of this unit to the initial factory settings. Notes • This procedure completely resets all the parameters of this unit including the “SET MENU” parameters. • The initial factory settings are activated next time you turn on this unit. y To cancel the initialization procedure at any time without making any changes, press A MASTER ON/OFF on the front panel to release it outward to the OFF position.
GLOSSARY Glossary ■ Audio and video synchronization (lip sync) Lip sync, an abbreviation for lip synchronization, is a technical term that involves both a problem and a capability of maintaining audio and video signals synchronized during post-production and transmission. Whereas the audio and video latency requires complex end-user adjustments, HDMI version 1.
Glossary ■ Dolby Surround ■ DTS Express Dolby Surround uses a 4-channel analog recording system to reproduce realistic and dynamic sound effects: 2 front left and right channels (stereo), a center channel for dialog (monaural), and a surround channel for special sound effects (monaural). The surround channel reproduces sound within a narrow frequency range. Dolby Surround is widely used with nearly all video tapes and laser discs, and in many TV and cable broadcasts as well.
Glossary ■ LFE 0.1 channel ■ S-video signal This channel reproduces low-frequency signals. The frequency range of this channel is from 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduced by the other 5/6 channels in Dolby Digital or DTS 5.1/6.1-channel systems.
SOUND FIELD PROGRAM INFORMATION Sound field program information ■ Elements of a sound field ■ CINEMA DSP 3D What really creates the rich, full tones of a live instrument are the multiple reflections from the walls of the room. In addition to making the sound live, these reflections enable us to tell where the player is situated as well as the size and shape of the room in which we are sitting.
PARAMETRIC EQUALIZER INFORMATION Parametric equalizer information This unit employs Yamaha Parametric room Acoustic Optimizer (YPAO) technology to optimize the frequency characteristics of its parametric equalizer to match your listening environment. YPAO uses a combination of the following three parameters (Frequency, Gain and Q factor) to provide highly precise adjustment of the frequency characteristics. ■ Q factor The width of the specified frequency band is referred to as the Q factor.
SPECIFICATIONS Specifications AUDIO SECTION • Minimum RMS Output Power for Front, Center, Surround, Surround back 20 Hz to 20 kHz, 0.04% THD, 8 Ω .................................... 130 W • Dynamic Power (IHF) 8/6/4/2 Ω ........................................................ 160/195/255/335 W • Maximum Useful Output Power (JEITA) [Asia, General, China and Korea models] 1 kHz, 10% THD, 8 Ω ........................................................ 175 W • Maximum Output Power [U.K.
Specifications GENERAL • Power Supply [U.S.A. and Canada models] .............................. AC 120 V, 60 Hz [General and Asia models] ....................................... AC 110/120/220/230–240 V, 50/60 Hz [China model] .................................................... AC 220 V, 50 Hz [Korea model] .................................................... AC 220 V, 60 Hz [Australia model] ............................................... AC 240 V, 50 Hz [U.K. and Europe models] .........................
SET MENU TREE SET MENU tree Press EMENU on the remote control AUTO SETUP MANUAL SETUP SPEAKER MENU CONFIG LFE/BASS OUT FRONT SP CENTER SP SUR. L/R SP SUR.B L/R SP PRESENCE SP CROSS OVER SUBWOOFER PHASE LEVEL DISTANCE TEST TONE VOLUME MENU ADAPTIVE DRC ADAPTIVE DSP LEVEL MUTING TYPE MAX VOL. INIT. VOL.
SET MENU tree PHONO CD TV MD/CD-R BD/HD DVD DVD CBL/SAT DVR VCR V-AUX DOCK BLUETOOTH OPTION MENU DISPLAY SET MEMORY GUARD INIT. CONFIG ZONE SET SYSTEM MEMORY LOAD SAVE SIGNAL INFO AUDIO VIDEO Notes *1Available depending on the parameter selected in “EQ TYPE”. *2Available when “VIDEO CONV.” is set to “ON”. *3Available when “HDMI RES.” is not set to “THRGH”. *4U.S.A. and Canada models only. *5Available when “INPUT CH” is set to “8ch”.
Index ■ Numerics 1 SPEAKER MENU, MANUAL SETUP .......................... 75 2 VOLUME MENU, MANUAL SETUP .......................... 77 2ch Stereo, sound field program .......... 44 3 SOUND MENU, MANUAL SETUP .......................... 78 3D indicator ......................................... 27 4 VIDEO MENU, MANUAL SETUP .......................... 80 5 INPUT MENU, MANUAL SETUP .......................... 81 5.1-channel speaker connection ........... 14 5.1-channel speaker layout ..................
Index ■ D D)LIPSYNC, SOUND MENU ............ 79 D)TEST TONE, SPEAKER MENU ... 77 D)ZONE SET, OPTION MENU ......... 85 Decoder descriptions ............................ 66 Decoder indicators ............................... 27 DECODER MODE, initial configuration ......................... 84 Decoder mode, initial configuration .... 84 DECODER MODE, INPUT MENU ... 82 Decoder mode, INPUT MENU ........... 82 Decoder parameter ............................... 73 Decoder selection ................................
Index ■ N Neo:6 Cinema ...................................... 66 Neo:6 Music ......................................... 66 neural indicator .................................... 27 NRL-THX ............................................ 66 NRL-THX Music ................................. 66 Number of speakers, automatic setup .. 31 ■ O ON SCREEN, Display settings ............ 84 On-screen display time, Display settings ................................ 84 Operation mode selector ......................
Index STEREO, sound field program ............ 44 Straight Enhancer, sound field program ......................... 44 STRAIGHT mode ................................ 45 Subwoofer ............................................ 12 SUBWOOFER jack ............................. 23 SUBWOOFER PHASE, speaker configurations ..................... 76 Subwoofer phase, speaker configurations ..................... 76 SUBWOOFER PRE OUT jack ............ 23 Supplied accessories ..............................
■ Front panel A B C M PURE DIRECT VOLUME AUDIO SELECT TONE CONTROL ENTER PRESET/TUNING/CH MEMORY SEARCH MODE STEREO/ MONO INFO CATEGORY BAND INPUT ZONE ON/OFF STRAIGHT MAIN ZONE ZONE CONTROLS MULTI ZONE EFFECT YPAO ON/OFF PROGRAM OPTIMIZER MIC SILENT CINEMA S VIDEO VIDEO ZONE 2 ZONE 3 L R AUDIO OPTICAL VIDEO AUX PHONES ON OFF MASTER Q D E F G H I J K L AUDIO SELECT TONE CONTROL ENTER PRESET/TUNING/CH MEMORY SEARCH MODE STEREO/ MONO CATEGORY INFO BAND
■ Remote control 1 C 2 3 STANDBY POWER V-AUX PHONO DOCK BD HD DVD DVD CD MD CD-R CBL SAT TV DVR VCR TUNER XM SIRIUS A POWER POWER TV AV MULTI AMP 4 TV SOURCE 5 6 7 SELECT MACRO ID ZONE MODE E F G SYSTEM MEMORY 1 TITLE BAND 8 9 SETUP D 2 PRESET/CH 4 3 VOLUME I CAT. A-E ENTER PARAMETER DISPLAY RETURN MEMORY H MENU SRCH MODE MUTE J K P REC 0 CLASSICAL 1 PRG SELECT CLASSICAL 1 A ENTERTAIN 3 STEREO 5 MOVIE 4 ENHANCER SUR.
Sound output in each sound field program L Front left speaker SL Surround left speaker SBR Surround back right speaker C Center speaker SR Surround right speaker PL Presence left speaker R Front right speaker SBL Surround back left speaker PR Presence right speaker Speaker from which no sound is being output Speaker from which sound is being output Speaker settings 7-channel PL Speaker settings 5-channel 7-channel PL PR C L L R C R 5-channel PR C L R L SR SL C R 5 1 S
Input audio source Program 3D 2-channel (monaural) 2-channel (stereo) 5.1-channel*1 6.1/7.1-channel*2 2 2 2 2 7 4 2 4 ENTERTAINMENT Sports Action Game Roleplaying Game Music Video Recital/Opera MOVIE Standard Spectacle Sci-Fi Adventure Drama ON MOVIE Mono Movie ON 2 2 2 2 OFF 3 2 2 4 STEREO 2ch Stereo –– 5 5 5 5 STEREO 7ch Stereo MUSIC ENHANCER 7ch Enhancer –– 4 4 4 4 SUR.DECODE Surround Decoder (Pro Logic) (PLII Movie) (PLII Game) –– 6 7 7 4 SUR.
List of remote control codes TV ACURA ADDISON 00101 01201, 01601, 08401 ADMIRAL 01301, 02201, 05801 ADVENT 09601 AGB 06801 AIKO 01201 AKAI 00101, 00301, 02901, 04601, 06801, 08901, 10501 AKURA 03701 ALBA 00101, 00401, 04801, 08501 AMERICA ACTION 02701 AMPRO 09401 AMSTRAD 00101, 00401, 02501, 04801, 05101, 05301, 06801 ANAM 00101, 02701, 03401 ANAM NATIONAL 03401, 08301 ANITECH 00101 AOC 00101, 00301, 00901, 01201, 01301, 01601, 02601, 02701, 05601 APEX DIGITAL09301, 09701, 09901 ASA 01401 AUDIOSONIC 00401
MEDION PENNEY 00301, 00501, 00601, 00901, 02101, 02601, 12201 PERDIO 04101 PHILCO 00301, 00401, 00801, 01801, 02601, 02701, 03301, 05801, 13101 PHILIPS 00001, 00301, 00401, 00601, 00801, 01201, 01601, 02601, 04901, 07001, 08801, 12601 PHONOLA 00401 PILOT 00301 PIONEER 01701, 02201, 02301, 03801, 08601, 09501, 11301 PORTLAND 01201 PRANDONI-PRINCE 06801 PRIMA 09601 PRISM 00601 PROFEX 00101, 04601 PROSCAN 00501 PROTECH 00101, 00401, 03301, 03701, 05201, 08501 PROTON 00101, 00301, 02601 PULSAR 00201 QUASAR 00
YAMAHA YAPSHE YOKO ZENITH 00301, 01801, 08301, 10001, 11001, 13501, 13601, 13701, 13801, 14001, 14101, 14201 03401 00401, 03701 00201, 01201, 02601, 05801 VCR ADMIRAL ADVENTURA AIKO AIWA 01102 00002 02102 00002, 00402, 02202, 02602, 02702 AKAI 00602, 02302 AKIBA 01402 ALBA 01402, 02102, 02302, 02702 AMERICA ACTION 02102 AMERICAN HIGH 00302 AMSTRAD 00002 ANAM 00402, 01902, 02002, 02102, 02902 ANAM NATIONAL 01902, 04502 ANITECH 01402 ASA 00402, 01502 ASHA 02002 ASUKA 00402 AUDIOVOX 00402, 02102 BAIRD 0000
SHARP SHINTOM SIEMENS CABLE ABC 00103, 00203 AMERICAST 02003 BELL SOUTH 02003 BIRMINGHAM CABLE COMMUNICATIONS 00803 BRITISH TELECOM 00103 DAERYUNG 00203, 01403, 01903 DIRECTOR 01303 FILMNET 01203 GENERAL INSTRUMENT 00103, 00803, 01303, 01703 GOLDSTAR 00503 HAMLIN 00303, 00703 JERROLD 00103, 00803, 01303, 01703 LG 00503 MEMOREX 00003 MNET 01203 MOTOROLA 00803, 01303, 01703, 02303 NOOS 01803 PACE 00603, 02203 PANASONIC 00003, 00203, 00403 PARAGON 00003 PHILIPS 01003, 01103 PIONEER 00503, 01603, 01903 PULSAR
CYRUS 00605 DENON 01005 DKK 00005 DMX ELECTRONICS 00605 DYNAMIC BASS 00805 EMERSON 00905 FISHER 00805 GENEXXA 00305, 00905 GOODMANS 00905 GRUNDIG 00605 HARMAN/KARDON 00605, 00705 HITACHI 00305 JVC 00505 KENWOOD 00105, 00405 KRELL 00605 LINN 00605 LXI 00905 MAGNAVOX 00605, 00905 MARANTZ 00205, 00605 MATSUI 00605 MCS 00205 MEMOREX 00905 MERIDIAN 00605 MICROMEGA 00605 MIRO 00005 MISSION 00605 MYRYAD 00605 NAD 00005 NAIM 00605 NSM 00605 OPTIMUS 00005, 00305, 00405, 00805, 00905 PANASONIC 00205 PHILIPS 00605 PIO
TAPE DECK AIWA 00111 CARVER 00111 GRUNDIG 00111 HARMAN/KARDON 00111 MAGNAVOX 00111 MARANTZ 00111 MYRYAD 00111 OPTIMUS 00011 PHILIPS 00111 PIONEER 00011 POLK AUDIO 00111 RCA 00011 REVOX 00111 SANSUI 00111 SONY 00211 THORENS 00111 WARDS 00011 YAMAHA 00311, 00411 APPENDIX x
RX-V1900_U-cv.fm Page 1 Friday, June 20, 2008 11:23 AM U RX-V1900 RX-V1900 AV Receiver OWNER’S MANUAL © 2008 Yamaha Corporation All rights reserved. Black process 45.0° 240.
UC RX-V1900 The circled numbers and alphabets correspond to those in the Owner’s Manual. Les nombres et lettres dans un cercle correspondent à ceux du mode d’emploi.
■ Remote control / Boîtier de télécommande 1 C 2 3 STANDBY POWER V-AUX PHONO DOCK BD HD DVD DVD CD MD CD-R CBL SAT TV DVR VCR TUNER XM SIRIUS A POWER POWER TV AV MULTI AMP 4 TV SOURCE 5 6 7 SELECT MACRO ID ZONE MODE E F G SYSTEM MEMORY 1 TITLE BAND 8 9 SETUP D 2 PRESET/CH 4 3 VOLUME MENU SRCH MODE I CAT.
