G NATURAL SOUND AV RECEIVER AMPLI-TUNER AUDIO-VIDEO NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095RDS VOLUME INPUT SELECTOR l6 20 STANDBY/ON l2 28 8 60 2 4 40 INPUT MODE 0 –dB SPEAKERS A B PROGRAM EFFECT A/B/C/D/E EXT.
Congratulations! You are the proud owner of a Yamaha Digital Sound Field Processing (DSP) System—an extremely sophisticated audio component. The DSP system takes full advantage of Yamaha’s undisputed leadership in the field of digital audio processing to bring you a whole new world of listening experiences.
English CONTENTS CAUTION .................................................................. 2 BASIC OPERATION ............................................... 34 Playing a source .................................................... 34 INTRODUCTION ....................................................... 3 Features .................................................................... 3 Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD)......................... 39 What’s DSP?...
CAUTION : Read this before operating your unit. 1. To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2. Install this unit in a cool, dry, clean place – away from windows, heat sources, sources of excessive vibration, dust, moisture and cold. Avoid sources of humming (transformers, motors). To prevent fire or electrical shock, do not expose the unit to rain or water. 3. Never remove the unit cover.
Features 7 Channel Power Amplification Main: 100W + 100W (8Ω) RMS Output Power, 0.02% THD, 20–20,000 Hz Center: 100W (8Ω) RMS Output Power, 0.02% THD, 20–20,000 Hz Rear: 100W + 100W (8Ω) RMS Output Power, 0.02% THD, 20–20,000 Hz Front effect: 25W + 25W (8Ω) RMS Output Power, 0.
INTRODUCTION What’s DSP? Introduction Welcome to the exciting world of digital home entertainment. This unit is one of the most complete and advanced AV receiver available. Some of the more advanced features may not be familiar to you, but they are easy to use. State-of-the-art technologies such as Dolby Digital and Digital Theater Systems (DTS) may be new to your home, but you have probably experienced the amazing realism they bring to feature films in theaters around the world.
INTRODUCTION Dolby Digital is the next level of Dolby Surround sound system developed for 35 mm film-movies by employing low bit-rate audio coding. Dolby Digital is a digital surround sound system that provides completely independent multi-channel audio to you. Dolby Digital provides five full range channels in what is sometimes referred to as a “3/2” configuration: three front channels (left, center and right), and two surround channels.
INTRODUCTION CINEMA DSP: Dolby Surround + DSP / DTS + DSP The Dolby Surround sound and DTS systems show their full ability in a large movie theater, because movie sounds are originally designed to be reproduced in a large movie theater that uses a multitude of speakers. Trying to create a sound environment similar to that of a movie theater in your home is difficult because of the room size, material inside the walls, the number of speakers, and so on.
Getting started English GETTING STARTED Unpacking Carefully remove this unit and accessories from the box. You should find the unit itself and the following accessories. Remote controller Indoor FM Antenna AM Loop Antenna Batteries (size AA, LR6, UM-3) User function stickers Opening and closing the front cover Close the front cover whenever the controls inside the panel are not used.
GETTING STARTED Installing batteries in the remote controller Notes about the remote controller Battery replacement Since the remote controller will be used for many of this unit’s control operations, you should begin by installing the supplied batteries. 1. Turn the remote controller over and slide the battery compartment cover in the direction of the arrow. 2. Insert the batteries (AA, LR6, UM-3 type) according to the polarity markings on the inside of the battery compartment. 3.
GETTING STARTED English Controls and their functions Front panel 1 2 3 NATURAL SOUND AV RECEIVER 4 6 5 CINEMA DSP 7ch RX V2095RDS VOLUME INPUT SELECTOR l6 20 l2 28 STANDBY/ON 8 4 40 INPUT MODE 2 60 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT BASS TONE EXTENSION BYPASS BASS l 0 l 2 3 89 0 AB 3 4 5 C l 2 4 5 BALANCE l 3 4 5 0 2 3 4 7 TREBLE l 2 5 0 l 2 3 3 4 L5 5R SOURCE TAPE/MD TV/DBS VCR 1 VCR 2 RDS MODE EON MODE START PRESET /TUNING FM/AM MEMO
GETTING STARTED 7 SPEAKERS switches D EXT. DECODER button Press the switch A or B (or both) for the main speakers you will use to select them. Press the switch for the main speakers you will not use again to cancel them. On the display panel, “SPEAKERS A” and/or “SPEAKERS B” will be illuminated, depending on which main speakers are being selected. Press this button to select the input signals from the EXTERNAL DECODER INPUT terminals as the input source.
GETTING STARTED English K RDS MODE button When an RDS station is received, pressing this button changes the display mode into the PS mode, PTY mode, RT mode and/or CT mode (if the station employs these RDS data services) in turn. L EON button Press this button to select a desired program type (NEWS, INFO, AFFAIRS, SPORT) when you want to call a radio program of that program type automatically. M PTY SEEK MODE button Press this button to set the unit to the PTY SEEK mode.
GETTING STARTED Display panel 1 2 3456 MEMORY DVD/LD PS PTY TV/DBS RT CT STEREO AUTO VCR 1 EON PTY HOLD NEWS VCR 2 INFO V-AUX SPORT AFFAIRS DIGITAL PRO LOGIC DSP SPEAKERS A B 89 0 AB 1 indicators Either of the “dts” indicators will be illuminated when the built-in DTS decoder is turned on. A red “dts” indicator will be illuminated when playing a compact disc or laserdisc encoded with DTS. An orange “dts” indicator will be illuminated when playing a DVD encoded with DTS.
English PREPARATION Speaker setup m Setting up your speaker system This unit has been designed to provide the best sound field quality with a full seven-speaker system setup, using a pair of main speakers to output main source sounds, two extra pairs of effect speakers to generate the sound field plus one center speaker for dialog. We therefore recommend that you use a seven-speaker setup.
PREPARATION m Recommended speaker system configurations 4 Speaker System 5 Speaker System Basic system. Good for Audio/Video sources. You can enjoy widely diffused sound by only adding a pair of rear speakers to a basic stereo speaker system. By the use of a center speaker, center sounds (dialog, vocals etc.) are precisely localized. 1E. SYS. SETUP—Set to 5ch. (See page 29.) 1A. CENTER SP—Set to NONE. (See page 28.) 1E. SYS. SETUP—Set to 5ch. (See page 29.) 1A. CENTER SP—Set to LRG or SML.
PREPARATION English Connections Caution: Plug in this unit and other components after all connections are completed. All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s manual for each of your components. Audio/video source equipment ● ● Use RCA type pin plug cables for audio/video units with the exception described later. The output (or input) terminals of YAMAHA audio/video units numbered as 1, 3, 4, etc.
PREPARATION m Basic connections of video units LD player or DVD player AUDIO OUT VIDEO OUT (Europe model) TV/Satellite tuner AUDIO OUT VIDEO OUT AUDIO SIGNAL AUDIO SIGNAL PHONO VIDEO VIDEO SIGNAL S VIDEO DVD/LD DVD/LD TV/DBS TV/DBS 1 CD IN IN VCR 1 VCR 1 OUT OUT IN ( PLAY ) TAPE/MD GND 4 OUT ( REC ) FM ANT MAIN 75Ω UNBAL.
PREPARATION Even if you connect an audio/video unit to the OPTICAL (or COAXIAL) terminal of this unit, you must keep the unit connected with the same named analog audio signal terminals of this unit, because digital signal cannot be recorded by a tape deck or VCR connected to only analog audio signal terminals of this unit. You can switch the selection of input signals between “digital” and “analog” easily. (See page 37 for details.
PREPARATION m Connecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player You must also connect the optical digital signal output terminal of the DVD/LD/CD combi-player to the OPTICAL DVD/LD digital signal input terminal of this unit. This connection is necessary for playing back a DVD source with Dolby Digital or DTS decoded, and playing back an LD source with DTS decoded.
PREPARATION If your video cassette recorder, LD player, etc. and your monitor are equipped with “S” video terminals, connect them to this unit’s S VIDEO terminals, and connect this unit’s S VIDEO MONITOR OUT terminal to the “S” video input of your monitor. With this connection, you can play back and record high quality pictures. Otherwise, connect the “composite” video terminals from your video cassette recorder, LD player, etc.
PREPARATION m Connecting an external decoder of a future format to this unit This unit is equipped with additional 6-channel audio signal input terminals (for left main, right main, center, left rear surround, right rear surround and subwoofer channels) for inputting signals from an external decoder of a future format to this unit. To listen to a sound by reproducing signals input to these terminals, press the EXT. DECODER button on the front panel so that “EXT. DECODER IN” appears on the display.
PREPARATION English Speakers Use speakers with the specified impedance shown on the rear of this unit. Front effect speakers Rear speakers Left Right Right Left SPEAKERS CENTER REAR FRONT ( SURROUND ) CAUTION SEE INSTRUCTION MANUAL FOR CORRECT SETTING. MAIN A Center speaker COUPLER MAIN PRE MAIN OUT IN OUTPUT CENTER FRONT A REAR ( SURROUND ) B B CENTER : FRONT : REAR : MAIN A OR B: A B: 4ΩMIN. / SPEAKER 6ΩMIN. / SPEAKER 6ΩMIN. / SPEAKER 4ΩMIN. / SPEAKER 8ΩMIN.
PREPARATION Note on main speaker connections: Note on a subwoofer connection: One or two speaker systems can be connected to this unit. If you use only one speaker system, connect it to either the SPEAKERS A or B terminals. You may wish to add a subwoofer to reinforce low frequencies or to output low bass sound from the subwoofer channel when reproducing discrete signals.
PREPARATION The speaker connections described on page 21 are fine for most applications. If for some reason, however, you wish to drive main, center, front effect and/or rear speakers with your existing amplifier, etc., the following terminals are available for connecting external amplifier(s) to this unit. COUPLER MAIN PRE MAIN OUT IN CENTER OUTPUT FRONT 3 1 REAR ( SURROUND ) 4 2 34 MAIN PRE OUT/MAIN IN terminals FRONT terminals These terminals are for front effect channel line output.
PREPARATION Antennas ● ● Each antenna should be connected to the designated terminals correctly, as shown in the following figure. Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience poor reception quality only with the indoor antennas, the use of an outdoor antenna may result in improvement.
PREPARATION Connect the included indoor antenna to the 75Ω UNBAL. FM ANT terminal. GND terminal For maximum safety and minimum interference, connect the GND terminal to a good ground. A good ground is a metal stake driven into moist earth. English m Connecting the indoor FM antenna Note Do not use an outdoor FM antenna and the indoor FM antenna at the same time.
PREPARATION Plugging in this unit • After completing all connections, plug the AC power cord into an AC outlet. • Unplug the AC power cord from the AC outlet if this unit is not to be used for a long period of time. SPEAKERS To AC outlet REAR AC OUTLETS SWITCHED I00W MAX. TOTAL ( SURROUND ) ON MANUAL FOR CORRECT SETTING. MAIN A B CENTER : FRONT : REAR : MAIN A OR B: A B: 4ΩMIN. / SPEAKER 6ΩMIN. / SPEAKER 6ΩMIN. / SPEAKER 4ΩMIN. / SPEAKER 8ΩMIN.
PREPARATION English On screen display If you connect your VCR, LD player, video monitor, etc. to this unit, you can take advantage of this unit’s capability to display program titles, parameter data and information for various setting changes and adjustments on your video monitor screen. This information will be superimposed over the video image. If there is no video source connected or it is turned off, the information will be displayed over a blue colored background.
PREPARATION Selecting the output modes (“SET MENU” mode) The following functions control the output signals to the speakers in your audio system. When speaker connections are all completed, select a proper position on each function to maximize the performance of your speaker system. * For details about the SET MENU mode, refer to pages 62 to 65. 1. SPEAKER SET 1A. CENTER SP 1B. REAR SP 1C. MAIN SP 1D. LFE/BASS OUT 1E. SYS. SETUP 1F. MAIN LEVEL m Function description 1A. CENTER SP 1B.
PREPARATION 1E. SYS. SETUP Choices: LARGE/SMALL Preset position: LARGE Choices: 7ch/5ch Preset position: 7ch LARGE: If your main speakers have a high ability for bass reproduction. In this position, full range signals present at the main channels are output from the main speakers. 7ch: If your speaker system includes a pair of front effect speakers. 5ch: If your speaker system does not include a pair of front effect speakers.
PREPARATION m Changing selections Refer to the display panel or the monitor screen when changing the selections. 2 1 1 NATURAL SOUND AV RECEIVER VOLUME 20 INPUT MODE 2 2 60 0 EFFECT PRESET STATIONS TUNING A/B/C/D/E EXT.
PREPARATION This procedure lets you adjust the sound output level balance between the main, center, rear and front effect speakers using the built-in test tone generator. After the adjustments, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Digital decoder, the Dolby Pro Logic Surround decoder and the DTS decoder.
PREPARATION TV CONCERT VIDEO THEATER STADIUM 7 NATURAL SOUND AV RECEIVER 8 10 VOLUME INPUT SELECTOR EFFECT 9 MOVIE MOVIE THEATER 1 THEATER 2 CINEMA DSP 7ch RX V2095 RDS / DTS SURROUND ON/OFF 12 11 l6 20 l2 LEVEL STANDBY/ON 28 8 60 2 PARAMETER 10 4 40 TEST INPUT MODE SET MENU 0 –dB SLEEP ON SCREEN SPEAKERS A B PHONES PROGRAM EFFECT PRESET STATIONS TUNING A/B/C/D/E EXT.
PREPARATION 2 5 6 EXT. DEC. TV CONCERT VIDEO THEATER STADIUM 7 8 MOVIE MOVIE THEATER 1 THEATER 2 10 11, 13 PHONO ROCK ENTERCONCERT TAINMENT 4 LEVEL 3 English 1 JAZZ CLUB 11 9 / DTS SURROUND EFFECT ON/OFF 12 PARAMETER 12 TEST SET MENU SLEEP ON SCREEN SYSTEM POWER ON MASTER VOLUME TV MUTE VCR STANDBY 11 For the front effect speaker level adjustment, press the TEST key on the remote controller again so that “TEST DSP” appears on the display.
BASIC OPERATION Playing a source REC/PAUSE A/B TAPE/MD A 4 2 CD 1 TUNER A DIR VCR 1 B STOP B DISC DVD/LD NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095 RDS 4 TV/DBS VOLUME INPUT SELECTOR VCR 2 l6 20 l2 28 STANDBY/ON C 8 4 40 PRESET INPUT MODE A/B/C/D/E 2 60 V-AUX 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT PRESET STATIONS TUNING A/B/C/D/E EXT.
BASIC OPERATION English REC/PAUSE A/B TAPE/MD A CD 5 7 TUNER A DIR VCR 1 B STOP B DISC DVD/LD 5 TV/DBS NATURAL SOUND AV RECEIVER VCR 2 CINEMA DSP 7ch RX V2095 RDS C VOLUME INPUT SELECTOR l6 20 l2 28 8 60 2 PRESET A/B/C/D/E V-AUX STANDBY/ON 4 40 INPUT MODE 8 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT BASS TONE EXTENSION BYPASS l 0 TREBLE l 2 l 2 3 3 4 5 l 2 3 4 4 5 5 0 l DVD/LD 2 2 3 3 4 4 L5 5R PTY SEEK REC OUT BALANCE l 3 4 5 0 2 PRES
BASIC OPERATION When you finish using this unit Press the STANDBY/ON switch on the front panel or the STANDBY key on the remote controller to enter the standby mode. Front panel Remote control STANDBY/ON or STANDBY To select the source connected to this unit’s EXTERNAL DECODER INPUT terminals as the input source. Press the EXT. DECODER button. “EXT. DECODER IN” will appear on the display. Front panel Remote control EXT. DECODER EXT. DEC.
BASIC OPERATION This unit allows you to switch the input mode for sources that send two or more types of signals to this unit. v For CD, TAPE/MD and TV/DBS sources: v For DVD/LD source: The following three input modes are provided. The following five input modes are provided. AUTO: AUTO: This mode is automatically selected when you turn on the power of this unit. In this mode, input signal is automatically selected by the following order of priority.
BASIC OPERATION Notes on input mode selection ● The input mode for a TV/DBS source is selected with function “7. TV/DBS INPUT” in the SET MENU mode. This unit will be automatically set to the selected input mode when the power is turned on. ● Set the input mode to the AUTO or D.D.RF mode to play a DVD/LD source encoded with Dolby Digital. ● Select the ANALOG mode to play a normal 2-channel source with a Dolby Pro Logic Surround program.
BASIC OPERATION English Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) m Recording the playing source to tape (or MD) REC/PAUSE A/B TAPE/MD A 2 3 CD TUNER A DIR VCR 1 B STOP B DISC DVD/LD 2 TV/DBS NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095 RDS VCR 2 C VOLUME INPUT SELECTOR l6 20 l2 28 8 60 2 PRESET A/B/C/D/E V-AUX STANDBY/ON 4 40 INPUT MODE HALL 1 HALL 2 CHURCH 1 2 3 PHONO 0 SPEAKERS A B PHONES PROGRAM EFFECT PRESET STA
BASIC OPERATION m Recording a source to tape (or MD) while listening to (or watching) another source The source (except for “SOURCE”) that is selected with the REC OUT selector can be recorded to a tape deck (MD recorder) and/or VCR, regardless of the INPUT SELECTOR setting.
BASIC OPERATION ● ● ● Dolby Digital RF audio input signal cannot be recorded by a tape deck or VCR. To record an LD source, the LD player must be connected to the OPTICAL digital audio signal input terminal and/or analog audio signal input terminals of this unit. A source of signals input to the EXTERNAL DECODER INPUT terminals of this unit cannot be recorded. Please check the copyright laws in your country to record from records, compact discs, radio, etc.
BASIC OPERATION Tuning Basic operation Quick automatic-search tuning (automatic tuning) is effective when the station signals are strong with no interference. However, manual tuning can be used during less-than-ideal conditions. NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095 RDS VOLUME INPUT SELECTOR l6 20 l2 28 STANDBY/ON INPUT MODE 1 3 8 4 40 2 60 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT A/B/C/D/E EXT.
BASIC OPERATION English Preset tuning m Manual preset tuning This unit can store station frequencies selected by the tuning operation. With this function, you can recall any desired station only by selecting the preset station number. Up to 40 stations (8 stations x 5 groups) can be stored.
BASIC OPERATION NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095 RDS VOLUME INPUT SELECTOR l6 20 l2 28 STANDBY/ON 8 4 40 INPUT MODE 2 60 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT PRESET STATIONS TUNING A/B/C/D/E EXT.
BASIC OPERATION You can make use of an automatic preset tuning function for RDS stations. With this function, this unit performs automatic tuning and stores RDS stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on page 43.
BASIC OPERATION m Exchanging preset stations You can exchange the places of two preset stations with each other as shown below. NATURAL SOUND AV RECEIVER CINEMA DSP 7ch RX V2095 RDS VOLUME INPUT SELECTOR l6 20 l2 28 STANDBY/ON 8 4 40 INPUT MODE 2 60 0 –dB SPEAKERS A B PHONES PROGRAM EFFECT PRESET STATIONS TUNING A/B/C/D/E EXT.
BASIC OPERATION English In areas where RDS broadcasts cannot be received, the RDS broadcast functions do not operate. (Skip the procedures from pages 47 to 51.) Receiving RDS stations RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal.
BASIC OPERATION m Program types in the PTY mode NEWS News: Short accounts of facts, events and publicly expressed views, reportage and actuality. AFFAIRS Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis. INFO Information: Program whose purpose is to impart advice in the widest sense, including meteorological reports and forecasts, consumer affairs, medical help, etc.
BASIC OPERATION When an RDS station is received, “PS”, “PTY”, “RT” and/or “CT” that correspond to the RDS data services employed by the station light up on the display. By pressing the RDS MODE button once or more, you can change the display mode among the RDS modes employed by the received station in the order shown below. (The RDS mode not employed by the station cannot be selected.
BASIC OPERATION Selecting your desired program type from among preset RDS stations (PTY SEEK) By designating a program type, the unit automatically searches all preset stations for an RDS station which broadcasts a program of that program type. * There are 15 program types for classifying RDS stations. For details, refer to page 48.
BASIC OPERATION English Automatic selection of desired program when broadcasting starts This function uses the EON (Enhanced Other Networks) data service on the RDS station network.
BASIC OPERATION Using digital sound field processor (DSP) This unit incorporates a sophisticated, multi-program digital sound field processor. The processor allows you to electronically expand and change the shape of the audio sound field from both audio and video sources, creating a theater-like experience in your listening room.
BASIC OPERATION English DVD/LD NATURAL SOUND AV RECEIVER TV/DBS CINEMA DSP 7ch RX V2095 RDS VOLUME INPUT SELECTOR l6 20 28 STANDBY/ON VCR 2 l2 8 INPUT MODE C 4 40 2 60 PRESET 0 A/B/C/D/E –dB V-AUX SPEAKERS A B PHONES PROGRAM EFFECT BASS TONE EXTENSION BYPASS BASS l 0 l 2 3 4 4 5 5 TREBLE BALANCE 0 0 l 2 3 PRESET STATIONS TUNING A/B/C/D/E EXT.
BASIC OPERATION m To enjoy a video source encoded with Dolby Pro Logic Surround, Dolby Digital or DTS Note If you change the LD (or CD) being played back with DTS decoded to another disc not encoded with DTS when the red “dts” indicator is illuminated, playing back the newly selected disc will output no sound. In this state, the red “dts” indicator flashes to show that this unit is locked in the DTS-decoding mode.
BASIC OPERATION English Adjusting output level of the center, right rear, left rear, front effect speakers and subwoofer You can adjust the sound output level of the each speaker even if the output level is already set in “Speaker balance adjustment” on pages 31 to 33. CENTER (Center speaker output level) R SUR. (Right rear speaker output level) L SUR.
BASIC OPERATION Speakers Control range (dB) Preset value CENTER RIGHT SURROUND (R SUR.) LEFT SURROUND (L SUR.) FRONT SUBWOOFER (SWFR) MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to +10 MIN, –20 to 0 0 0 0 0 0 Notes ● Once the output level is adjusted, the level value will be the same in all the digital sound field programs. ● 56 The value of each speaker output level you set the last time will remain memorized even when this unit is in the standby mode.
BASIC OPERATION English Brief overview of digital sound field programs The following list gives you a brief description of the sound fields produced by each of the DSP programs. Keep in mind that most of these are precise digital recreations of actual acoustic environments. The data for these sound fields were recorded at actual locations using sophisticated sound field measurement equipment.
BASIC OPERATION No. 4 5 6 7 58 PROGRAM JAZZ CLUB ROCK CONCERT ENTERTAINMENT STADIUM SUBPROGRAM (TYPE) FEATURE The Bottom Line This is the sound field at stage front in “The Bottom Line”, a famous New York Jazz club. The floor can seat 300 people to the left and right in a sound field offering real and vibrant sound. Village Gate A jazz club in New York. It is in a basement and has a relatively spacious floor area. The reflection pattern is similar to that of a small hall.
BASIC OPERATION ● These programs use the Dolby Pro Logic decoder, the Dolby Digital decoder or the DTS decoder. ● Speaker output for each program is as follows. English m Program No. 8 to 12: CINEMA-DSP programs (for Audio/Video sources) No. 8, 9, 10, 11: main, center, rear, front effect No. 12 (Normal): main, center, rear No. 12 (Enhanced): main, center, rear, front effect ● For program No. 8 and 9 only, indicators light up as follows.
BASIC OPERATION ● Program No. 10 to 11 are suitable for reproducing video discs, video tapes and similar sources which are encoded with Dolby Surround (bearing the “DOLBY SURROUND” or “DOLBY DIGITAL” logo) or encoded with DTS (bearing the “dts” logo). No. 10 PROGRAM MOVIE THEATER 1 SUBPROGRAM (TYPE) 70 mm Spectacle DSP ( PRO LOGIC ) Functions when the input signal is analog or PCM audio or encoded with Dolby Digital in 2 channels. FEATURE Creates the extremely wide sound field of a movie theater.
BASIC OPERATION Program No. 12 is for reproducing video discs, video tapes and similar sources which are encoded with Dolby Surround (bearing the “DOLBY SURROUND” or “DOLBY DIGITAL” logo) or encoded with DTS (bearing the “dts” logo). No. 12 PROGRAM /DTS SURROUND SUBPROGRAM (TYPE) FEATURE PRO LOGIC/Normal ( ) Functions when the input signal is analog or PCM audio or encoded with Dolby Digital in 2 channels.
ADVANCED FEATURES “SET MENU” mode The following eight functions maximize the performance of your system and increase the enjoyment of audio listening and video watching. 1. SPEAKER SET 2. DLBY DGTL SET 1A. CENTER SP 2A. LFE LEVEL 1B. REAR SP 2B. D-RANGE 1C. MAIN SP 05. PARAMETER INI 06. MEMORY GUARD 07. TV/DBS INPUT 3. DTS SET 1D. LFE/BASS OUT 08. DIMMER 3A. LFE LEVEL 1E. SYS. SETUP 4. CENTER DELAY 1F.
ADVANCED FEATURES English m Function description 1. SPEAKER SET (Selecting the output modes suitable for your speaker system) Refer to pages 28 to 30 for details. (Once you have selected proper modes, you do not have to make a setting change, unless your speaker system is modified.) 2. DLBY DGTL (DOLBY DIGITAL) SET Adjusting method After selecting the title “2. DLBY DGTL SET” in step 2 on page 62, press the + or – key to display the title “2A. LFE LEVEL”. To select the title “2B. D-RANGE”, press the key.
ADVANCED FEATURES 3. DTS SET Adjusting method After selecting the title “3. DTS SET” in step 2 on page 62, press the + or – key to display the title “3A. LFE LEVEL”. Then adjust its level with the + or – key. 3A. LFE LEVEL [Adjusting the output level at the LFE (low frequency effect) channel] ● Control range: –10 dB to 10 dB Preset value: 0 dB ● This adjustment is effective only when DTS is decoded and the signals of the selected source encoded with DTS contain LFE signals.
ADVANCED FEATURES If you wish to prevent accidental alteration to DSP parameters and other adjustments on this unit, select “ON”. In this position, they are locked and cannot be changed. The following functions on this unit can be locked by this operation. • • • • • English 6. MEMORY GUARD (Locking DSP parameters and other adjustments) DSP parameters Other functions in the “SET MENU” mode ON SCREEN display key LEVEL key TEST key 7.
ADVANCED FEATURES Creating your own sound fields What is a sound field? In order to explain the impressive functions of the DSP, we need to first understand what a sound field really is. What really creates the rich, full tones of a live instrument are the multiple reflections from the walls of the room. In addition to making the sound “live”, these reflections enable us to tell where the player is situated, and the size and shape of the room in which we are sitting.
ADVANCED FEATURES English m Selecting and editing program parameters This adjustment can be made only by using the remote controller and watching the monitor screen or the display panel. Note Information on the monitor screen would be easier to see than the display panel. V AUX HALL 1 1 3, 4 JAZZ CLUB 4 STADIUM 7 HALL 2 CHURCH 2 3 5 1 2 1 Set the PARAMETER/SET MENU switch to the PARAMETER position. Note: The cover of the remote controller must be open. LEVEL 6 EXT. DEC.
ADVANCED FEATURES m Descriptions of the digital sound field parameters Not all of the following parameters are found in every program. ● ROOM SIZE P. ROOM SIZE (Presence Room Size) How it Affects the Sound: Changes the apparent size of the music venue. The larger the value, the larger the simulated room will sound. Adjusts the apparent space size of the front presence sound field. The larger the value, the longer the interval between reflections becomes, which increases the depth of the sound source.
ADVANCED FEATURES LIVENESS (Presence Liveness) How it Affects the Sound: This parameter changes the apparent reflectivity of the walls in the hall. English ● LIVENESS Adjusts the apparent reflectivity of the walls on the front presence sound field. The larger the value, the more reflective the front presence sound field becomes.
ADVANCED FEATURES ● REV. LEVEL (Reverberation Level) This parameter adjusts the volume of the reverberation sound. The larger the value, the stronger the reverberation becomes. Control Range: 0 – 100% Level Direct sound REV. LEVEL Time ● S. DELAY (Surround Delay) Adjusts the delay between the direct sound and the first reflection on the rear surround side sound field. The larger the value, the later the surround sound field is generated.
ADVANCED FEATURES English Setting the SLEEP timer Use the built-in SLEEP timer to automatically turn this unit into the standby mode after the time you set elapses. The SLEEP timer is useful when you plan to fall asleep while this unit is playing back or recording a source. The SLEEP timer also automatically turns off external units connected to the SWITCHED AC OUTLETS on the rear of this unit. The SLEEP timer can only be set using the remote controller.
REMOTE CONTROLLER The remote controller can operate the main unit as well as other Yamaha audio and video components. The Macro feature allows you to program a series of functions in sequence onto a single key, or you can use one of the preset macros to operate other Yamaha components in your home theater.
REMOTE CONTROLLER For MD recorders: : Locates the beginning of the current or previous track. : Locates the beginning of the next track. 2 CD/DVD/LD player keys These keys control compact disc players, DVD players or LD players. Set the A/B/C switch (I) to the “A” position to control compact disc players, “B” position for DVD players and “C” position for LD players. * The DISC key is used for disc changers only. * The STOP key is used for DVD players and LD players only. 3 Tuner keys Control tuners.
REMOTE CONTROLLER Using the “learning-capable” keys (Cover is open) This is a learning remote controller. The shaded keys in the illustration shown below can be programmed to “learn” control functions from other remote controllers. This unit can be used in place of other remote controllers by learning their functions. It will be much convenient for you to operate various audio and video components.
REMOTE CONTROLLER About the lighting of keys When you press an input selector key, it lights up for about 3 seconds. English Notes • Area A cannot learn a new function. To store a new function, store it onto area B or C. • If a key which has a preset function learns a new function, the preset function will not work but is not deleted. When the learned function is cleared, the preset function is restored. (For information on clearing a learned function, refer to page 82.
REMOTE CONTROLLER Using OPERATION CONTROL keys (Cover is closed) When the cover of the remote controller is closed, you can easily operate Yamaha components including learned functions by using the OPERATION CONTROL keys.
REMOTE CONTROLLER To operate a Yamaha CD player 1. Press the “CD” input selector key. 2. Use the OPERATION CONTROL keys. (They carry out the functions in area A of keys 2.) OPERATION CONTROL Skip to previous track To operate your VCR 1. Press the “VCR” input selector key. 2. Use the OPERATION CONTROL keys. (They carry out the functions in area B of keys 1. This area is originally preset with no function. You must store the functions related to controlling the VCR in area B of keys 1 beforehand.
REMOTE CONTROLLER Macro operations (Cover is closed) The Macro feature makes it possible to operate a series of functions by pressing just one key. For example, when you want to play a CD, normally you would turn on the equipment, select the CD input, and press the play key to start playback. Using the Macro feature you can operate all those functions by simply pressing the CD macro key.
REMOTE CONTROLLER English The Macro feature allows you to operate several remote control functions in a programmed order by pressing one macro key. (Also, refer to the table on page 74.) Function of the key (and area) carried out when a macro key is pressed Macro key 2nd (Selects an input source.) 1st (Turns on this unit.) 3rd (Starts playback of a source.
REMOTE CONTROLLER Methods of learning and clearing functions m Learning a new function 1 Place this remote controller and the other remote controller so that they face each other. 5 Press and hold the key (on the other remote controller) which has the function you want to store.
REMOTE CONTROLLER English m Making a new macro A new macro can be programmed onto any preset macro key in place of the factory preset functions. (See page 78 to know what keys are preset macro keys.) You can make as many as 13 new macro keys. A macro key can learn as many as seven functions of other keys. Note If you store a continuous function such as lowering the volume level, it may not work well when carried out as a part of macro. 1 4 TRANSMIT /LEARN CLEAR LEARN MACRO Flashes slowly.
REMOTE CONTROLLER m Clearing learned functions To Clear a Learned Function 1 To Clear All Learned Functions To clear a learned key function, press the LEARN button using a ball-point pen or similar object. To clear a macro you made, press the MACRO button. 1 Select the kind of key functions all of which you want to clear by using the MACRO switch on the side panel of the remote controller. or SLOW QUICK OFF MACRO TRANSMIT /LEARN CLEAR LEARN MACRO OFF: Flashes slowly.
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, disconnect the power cord and contact your authorized YAMAHA dealer or service center. English TROUBLESHOOTING General Problem Cause What to Do The unit fails to turn on when the STANDBY/ON switch is pressed, or turns into the standby mode suddenly soon after the power is turned on.
TROUBLESHOOTING Problem Cause What to Do DSP parameters and some other settings on this unit cannot be changed. The function “6. MEMORY GUARD” in the SET MENU mode is set to the “ON” position. Set to the “OFF” position. “INPUT DATA ERR” appears on the display and no sound is heard. A nonstandardized source is played back, or the unit playing back a source is misoperating. Check the source, or turn off the unit playing back the source and then turn on again. The sound field cannot be recorded.
TROUBLESHOOTING Cause What to Do FM stereo reception is noisy. Because of the characteristics of FM stereo broadcasts, this is limited to cases where the transmitter is too far away or the antenna input is poor. Check the antenna connections. Try using a high quality directional FM antenna. Set the TUNING MODE button to the manual tuning mode. There is distortion and clear reception cannot be obtained even with a good FM antenna. There is multipath interference.
SPECIFICATIONS AUDIO SECTION Minimum RMS Output Power Per Channel (When both channels are driven) MAIN L/R (20 Hz to 20 kHz, 0.02% THD, 8 ohms) ....................... 100W+100W CENTER (20 Hz to 20 kHz, 0.02% THD, 8 ohms) ................................... 100W REAR L/R (20 Hz to 20 kHz, 0.02% THD, 8 ohms) .........................100W+100W FRONT L/R (1 kHz, 0.05% THD, 8 ohms) ....................................................
SPECIFICATIONS Harmonic Distortion (1 kHz) [U.S.A., Canada, China and General models] Mono/Stereo ..................................0.1/0.2% [Europe, Australia and Singapore models] Mono/Stereo (40 kHz Dev.) ...........0.1/0.2% Stereo Separation (1 kHz) [U.S.A., Canada, China and General models] ..............................................................48 dB [Europe, Australia and Singapore models (40 kHz Dev.)].......................................48 dB Frequency Response 20 Hz to 15 kHz ............
YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND SCANDINAVIA A.