manual

ManualsBrandsYamaha ManualsStereo ReceiverRX-V3900

Firmware Update Procedure for RX-V3900

Page.1 of 6

February, 2010

Subject: RX-V3900 Firmware Update ver. 1.11

Yamaha is pleased to offer this firmware update to ensure the best possible

performance for your Yamaha RX-V3900 AV Receiver.

This firmware improves HDMI standby through function.

The following pages contain the firmware update instructions for the RX-V3900.

You can easily update the latest firmware either by using an USB thumb drive, or

by connecting the receiver to the Internet. In order to properly execute the update,

read all instructions carefully. The following links will also lead you directly to the

beginning of each individual section of the instructions.

9 Click here to confirm the current firmware version before the update.

9 Click here for the firmware update by USB thumb drive.

(Update by Network is recommended if your receiver is connected to the internet)

9 Click here for the firmware update by Network.

9 Click here for the firmware version confirmation after update.

9 Click here for troubleshooting.

< IMPORTANT NOTICE >

Do not attempt to update your Yamaha receiver using any other data file except those provided

directly from the Yamaha website or through your network connection.

Follow the instructions carefully and do not attempt any other procedures not specified in the

instructions provided by Yamaha.

Improperly updated products may cause improper operation, and any parts or service required

to restore proper operation will not be covered under the Yamaha Limited Warranty.

Summary of content (6 pages)

PAGE 1
Firmware Update Procedure for RX-V3900 February, 2010 Subject: RX-V3900 Firmware Update ver. 1.11 Yamaha is pleased to offer this firmware update to ensure the best possible performance for your Yamaha RX-V3900 AV Receiver. This firmware improves HDMI standby through function. The following pages contain the firmware update instructions for the RX-V3900. You can easily update the latest firmware either by using an USB thumb drive, or by connecting the receiver to the Internet.
PAGE 2
Firmware Update Procedure for RX-V3900 Confirming the firmware version Step1: Set the MASTER ON/OFF button on the front panel to OFF, and confirm that the AC power cable is properly connected to an outlet. Step2 While pressing the STRAIGHT button, press (and release) the MASTER ON/OFF button and then keep pressing the STRAIGHT key until “ADVANCED SETUP” appears on the front panel display. (Note: “ADVANCED SETUP” is only displayed for a few seconds.
PAGE 3
Firmware Update Procedure for RX-V3900 Instruction for USB Update Requirement: (Formatting by FAT system is required in advance). - USB thumb drive, with enough free space to store over 16 MB. - Firmware file provided by YAMAHA,”RXV3900-xxxx.bin”. Step1: Delete any existing files in the USB thumb drive. Step2: Copy the downloaded firmware “RXV3900-xxxx.bin” into the root directory of the USB thumb drive. Drag & Drop the file into USB drive.
PAGE 4
Firmware Update Procedure for RX-V3900 Step5 Rotate the PROGRAM selector counterclockwise to select “FIRM UPDATE USB”. Step6 To start the firmware update, press the MENU button. (Allow about 10 minutes for the update) Firmware reprogramming in progress Caution! Do not interrupt power or remove the USB thumb drive during the update. In case the power is accidentally cut off, refer to troubleshooting procedures on page 6 to recover.
PAGE 5
Firmware Update Procedure for RX-V3900 Instruction for Network Update Requirement: Network environment to be able to connect to the Internet via RX-V3900. (For more information, refer to the owner’s manual.) Step1: Set the MASTER ON/OFF button on the front panel to OFF, and confirm that the AC power cable is properly connected to an outlet.
PAGE 6
Firmware Update Procedure for RX-V3900 Troubleshooting Firmware Update Case #1: Instead of “UPDATE OK”, an error message appeared on the display during updating or “ERROR” appeared when confirming the firmware version in Advanced Setup. To recover, retry the update procedure of USB/Network from first step again. In case the update has failed with network method, perform USB update method for recovery. Case #2: “Thumb Data Err” / “Firm Update” appeared on the display. To recover, 1. Press MENU button.