U RX-V661 AV Receiver OWNER’S MANUAL
IMPORTANT SAFETY INSTRUCTIONS Important safety instructions 10 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important safety instructions d) 20 21 22 23 If the product does not operate normally by following the operating instructions.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. Caution: Read this before operating your unit. 1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. 2 Install this sound system in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 30 cm on the top, 20 cm on the left and right, and 20 cm on the back of this unit.
Contents Notice ....................................................................... 2 Features ................................................................... 3 Supplied accessories .................................................. 3 Getting started ........................................................ 4 Quick start guide .................................................... 5 Connections ...........................................................
NOTICE Notice About this manual • y indicates a tip for your operation. • Some operations can be performed by using either the buttons on the front panel or the ones on the remote control. In case the button names differ between the front panel and the remote control, the button name on the remote control is given in parentheses. • This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc.
Features Features HDMI (High-Definition Multimedia Interface) ◆ Minimum RMS output power (20 Hz to 20 kHz, 0.06% THD, 8 :) Front: 90 W + 90 W Center: 90 W Surround: 90 W + 90 W Surround back: 90 W + 90 W ◆ HDMI interface for standard, enhanced or high-definition video (includes 1080p video signal transmission) as well as multi-channel digital audio based on HDMI version 1.
GETTING STARTED Getting started ■ Installing batteries in the remote control 1 3 Caution 2 1 Take off the battery compartment cover. 2 Insert the two supplied batteries (AA, R6, UM-3) according to the polarity markings (+ and –) on the inside of the battery compartment. 3 Snap the battery compartment cover back into place. Notes • Change all of the batteries if you notice the following conditions: – the operation range of the remote control decreases.
Quick start guide Quick start guide Video monitor Front right speaker Front left speaker INTRODUCTION The following steps describe the easiest way to enjoy DVD movie playback in your home theater. Preparation: Check the items Subwoofer Surround right speaker In these steps, you need the following supplied accessories. ❏ AM loop antenna ❏ Indoor FM antenna Center speaker Surround back right speaker DVD player Surround back left speaker Surround left speaker Step 1: Set up your speakers ☞ P.
Quick start guide Step 1: Set up your speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. Place your speakers in the room and connect them to this unit. AUDIO MULTI CH INPUT L L R R CENTER ZONE 2 OUT PRE OUT SINGLE Front speakers and center speaker VIDEO CENTER VIDEO GND PHONO DOCK CD IN MD/ OUT (PLAY) CD-R (REC) DVD DTV/CBL IN DVR OUT IN OUT VCR S VIDEO FRONT(6CH) SB(8CH) SURROUND SUB WOOFER FRONT SURROUND SUR.
Quick start guide Step 2: Connect your DVD player and other components MULTI CH INPUT L R CENTER ZONE 2 OUT PRE OUT SINGLE Connect the video cable to the composite video output jack of your DVD player and DVD VIDEO jack of this unit. VIDEO CENTER VIDEO GND PHONO DOCK CD IN MD/ OUT (PLAY) CD-R (REC) DVD DTV/CBL IN DVR OUT IN OUT VCR S VIDEO FRONT(6CH) SB(8CH) SURROUND XM SUB WOOFER FRONT SURROUND SUR.
Quick start guide 4 Connect the supplied AM loop antenna and indoor FM antenna to this unit. See page 24 for the connection information. ■ For further connections • Using the other kind of speaker combinations ☞ P. 12 • Connecting a video monitor via various ways of the connection ☞ P. 18 AM loop antenna • Connecting a DVD player via various ways of the connection ☞ P. 19 • Connecting a DVD recorder or a digital video recorder ☞ P.
Quick start guide Step 3: Turn on the power and press SCENE 1 button 4 Start playback of the desired DVD on your player. If the connected DVD player is a Yamaha product and has capability of the SCENE control signals with the REMOTE OUT jack of this unit (see page 23), this unit can automatically activate the DVD player and start playback when you press the F SCENE1 button. Refer to the instruction manual of the DVD player for further information. Check the type of the connected speakers.
Quick start guide Notes • To use the “TV Viewing” template (Case B), you must connect a satellite receiver, a cable TV receiver or an HDTV decoder to this unit in advance. See page 20 for details. • To use the “Radio Listening” template (Case C), you have to tune into the desired radio station. See pages 50 to 52 for the tuning information. • To achieve the best possible reception, orient the connected AM loop antenna, or adjust the position of the end of the indoor FM antenna.
CONNECTIONS Connections Rear panel AUDIO jacks Connect the analog audio cable plugs. ☞ P. 18-21 MULTI CH INPUT jacks Connect the input source component equipped with the multi-channel output jacks. ☞ P. 22 DOCK terminal Connect a Yamaha iPod universal dock (sold separately). ☞ P. 23 AUDIO MULTI CH INPUT PRE OUT jacks Connect external amplifiers and an active subwoofer. ☞ P. 22 CENTER ZONE 2 OUT PRE OUT SINGLE VIDEO CENTER VIDEO L L Video jacks Connect the video cable plugs. ☞ P.
Connections . Placing speakers The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multichannel audio sources. PL PR C FR FL PR FR PL SW FL 30˚ C SL SR SR SBR SBL SL 60˚ SL 80˚ SBL SR SBR 1.8 m (6 ft) 30 cm (12 in) or more Front left and right speakers (FL and FR) The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the ideal listening position.
Connections Connecting speakers Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty, this unit cannot reproduce the input sources accurately. Note PREPARATION Caution • Before connecting the speakers, make sure that this unit is turned off (see page 25). • Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage this unit and/or the speakers.
Connections ■ Connecting the speaker cable 1 Remove approximately 10 mm (0.4 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits. ■ Connecting the banana plug (except Europe, Asia and Korea models) Tighten the knob and then insert the banana plug connector into the end of the corresponding terminal. 10 mm (0.4 in) 2 Loosen the knob.
Connections Information on jacks and cable plugs Audio jacks and cable plugs AUDIO R (White) (Red) L R Left and right analog audio cable plugs DIGITAL DIGITAL COAXIAL OPTICAL (Orange) C Coaxial digital audio cable plug VIDEO S VIDEO (Yellow) O V Optical digital audio cable plug Composite video cable plug S S-video cable plug COMPONENT VIDEO Y PB PR (Green) (Blue) (Red) Y PB PR Component video cable plugs ■ Audio jacks ■ Video jacks This unit has three types of audio jacks.
Connections Information on HDMI™ ■ HDMI compatibility with this unit Audio signal types Audio signal formats Compatible HDMI components 2ch Linear PCM 2ch, 32-192 kHz, 16/20/24 bit CD, DVD-Video, DVD-Audio, etc. Multi-ch Linear PCM 8ch, 32-192 kHz, 16/20/24 bit DVD-Audio, etc. DSD 2/5.1ch, 2.8224 MHz, 1 bit SACD, etc. Bitstream Dolby Digital, DTS DVD-Video, etc. HDMI HDMI cable plug y This unit’s HDMI interface is based on the following standards: • HDMI Version 1.
Connections Audio and video signal flow ■ Audio signal flow Input ■ Video signal flow Output Input HDMI Output HDMI DIGITAL AUDIO (COAXIAL) AUDIO PREPARATION COMPONENT VIDEO DIGITAL AUDIO (OPTICAL) S VIDEO VIDEO Digital output Through Analog output Video conversion ON (see page 81) Notes Notes • 2-channel as well as multi-channel PCM, Dolby Digital and DTS signals input at the HDMI IN 1 or HDMI IN 2 jack can be output at the HDMI OUT jack only when “SUPPORT AUDIO” is set to “OTHER” (see pa
Connections Connecting a TV monitor or projector Connect your TV (or projector) to the HDMI OUT jack, the COMPONENT VIDEO MONITOR OUT jacks, the S VIDEO MONITOR OUT jack or the VIDEO MONITOR OUT jack of this unit. Notes • Some video monitors connected to this unit via a DVI connection fail to recognize the HDMI audio/video signals being input if they are in the standby mode. In this case, the HDMI indicator flashes irregularly.
Connections Connecting other components Make sure that this unit and other components are unplugged from the AC wall outlets. Notes ■ Connecting a DVD player PREPARATION • When “VIDEO CONV.” is set to “OFF” (see page 81), be sure to make the same type of video connections as those made for your TV (see page 18). For example, if you connected your TV to the VIDEO MONITOR OUT jack of this unit, connect your other components to the VIDEO jacks. • When “VIDEO CONV.
Connections ■ Connecting a DVD recorder, PVR or VCR DVD recorder, PVR or VCR S-video in Audio out Audio in Video in Video out R L R L S-video out V V S AUDIO S VIDEO VIDEO S VIDEO IN DVR OUT IN VCR IN OUT DVR OUT IN OUT VCR COMPONENT VIDEO PR PB C S S V Video in S-video in S-video out Video out Audio in L V Y DVR PR PB Y Component video out R Audio out L R DVD recorder, PVR ■ Connecting a set-top box Satellite receiver, cable TV receiver or HDTV decoder S-v
Connections ■ Connecting audio components Notes • To make a digital connection to a component other than the default component assigned to each the DIGITAL INPUT jack or the DIGITAL OUTPUT jack, select the corresponding setting for “OPTICAL OUT”, “OPTICAL IN”, or “COAXIAL IN” in “I/O ASSIGNMENT” (see page 78). • Connect your turntable to the GND terminal of this unit to reduce noise in the signal. However, you may hear less noise without the connection to the GND terminal for some turntables.
Connections ■ Connecting an external amplifier This unit has more than enough power for any home use. However, if you want to add more power to the speaker output or if you want to use another amplifier, connect an external amplifier to the PRE OUT jacks. Notes • • • • • When you make connections to the PRE OUT jacks, do not make connections to the SPEAKERS terminals. The signals output at the FRONT PRE OUT jacks are affected by the TONE CONTROL settings (see page 48).
Connections ■ Connecting a Yamaha iPod universal dock This unit is equipped with the DOCK terminal on the rear panel that allows you to connect a Yamaha iPod universal dock (such as the YDS-10, sold separately) where you can station your iPod and control playback of your iPod using the supplied remote control. Connect a Yamaha iPod universal dock to the DOCK terminal on the rear panel of this unit using its dedicated cable.
Connections Connecting the FM and AM antennas Connecting the power cable (U.S.A. model) Both FM and AM indoor antennas are supplied with this unit. Connect each antenna correctly to the designated terminals. In general, these antennas should provide sufficient signal strength. y See page 8 for connection information of the supplied indoor FM antenna and AM loop antenna. Notes AC OUTLETS • The AM loop antenna should be placed away from this unit.
Connections Setting the speaker impedance Caution If you are to use 6 ohm speakers, set “SP IMP.” to “6: MIN” as follows BEFORE using this unit. 4 ohm speakers can be also used as the front speakers. 1 Press and hold C TONE CONTROL on the front panel and then press B MASTER ON/ OFF inward to the ON position to turn on this unit. This unit turns on, and the advanced setup menu appears in the front panel display.
Connections Front panel display Note The XM indicator is only applicable to the U.S.A. and Canada models and the cursor on the left of the XM indicator lights up only when “XM” is selected as the input source. For details, see “Basic XM Satellite Radio operations” on page 54.
Connections L Multi-information display Shows the name of the current sound field program and other information when adjusting or changing settings. M SLEEP indicator Lights up while the sleep timer is on (see page 41). Using the remote control The remote control transmits a directional infrared ray. Be sure to aim the remote control directly at the remote control sensor on this unit during operation. N 96/24 indicator Lights up when a DTS 96/24 signal is input to this unit.
OPTIMIZING THE SPEAKER SETTING FOR YOUR LISTENING ROOM Optimizing the speaker setting for your listening room This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening environment.
Optimizing the speaker setting for your listening room 4 Press l / h to select the desired setting for “EXTRA SP ASSIGN” and then press n. 6 Extra speaker assignment EXTRA SP ASSIGN Selects the function of the speakers connected to the EXTRA SP terminals. Choices: FRONT B, ZONE2, PRESENCE, NONE • When you use the Zone 2 speakers (see page 90) Select “ZONE2” to set the function of the speakers to the Zone 2 speakers. This unit drives the Zone 2 speakers by using the internal amplifier.
Optimizing the speaker setting for your listening room This unit performs the following checks: The results displayed under “RESULT” are as follows. Speaker wiring WIRING Checks which speakers are connected and the polarity of each speaker. Number of speakers SP Displays the number of speakers connected to this unit in the following order: Front/Back/Subwoofer Speaker size SIZE Checks the frequency response of each speaker and sets the appropriate low-frequency crossover for each channel.
Optimizing the speaker setting for your listening room 9 Press l / h repeatedly to toggle between the setup result displays. 10 Press ENTER to return to the top “AUTO:RESULT” display. Results of the speaker connection and wiring AUTO:RESULT . RESULT SP : 3/4/0.1 DIST: 14.0/17.0ft LVL : -9.0/+6.
Optimizing the speaker setting for your listening room ■ If an error screen appears 2 Press k / n / l / h to select “RETRY” or “EXIT” and then press ENTER. The following display is an example where “E-9:USER CANCEL” appears in the OSD. Press l / h repeatedly to toggle between the warning displays. WARNING:W-1 Reverse Channel FL -CENTER PL PR SL SR SBL SBR [[]/[[]:Select [ENTER]:Return AUTO:ERROR . E-9:USER CANCEL Don't operate any function.
SELECTING THE SCENE TEMPLATES Selecting the SCENE templates This unit is equipped with 18 preset SCENE templates for various situations of using this unit. As the initial factory setting, the following SCENE templates are assigned to each SCENE button: 2 SCENE 1: DVD Viewing SCENE 2: Disc Listening SCENE 3: TV Viewing SCENE 4: Radio Listening Rotate the I INPUT selector (or set the operation mode selector to AMP and then press l / h) to select the desired template.
Selecting the SCENE templates ■ Which SCENE template would you like to select? Which source do you like to play back? Which component do you like for playback? Video sources (DVD video, Recorded video) DVD SCENE templates Default SCENE buttons DVD Viewing 1 DVD Movie Viewing DVD Live Viewing Music discs (CD, SACD or DVD-Audio) DVR DVR Viewing DVD Disc Hifi Listening Music Disc Listening Disc Listening CD 2 CD Hifi Listening CD Listening CD Music Listening Radio programs * Radio Listening
Selecting the SCENE templates ■ Preset SCENE templates descriptions The illustrations of the SCENE button in the following table indicate the assigned SCENE buttons as the default setting. SCENE template Input source Playback mode DVD Viewing DVD*1 Features STRAIGHT DVD Movie Viewing DVD*1 MOVIE Sci-Fi Select this SCENE template when you play back movies on your DVD player.
Selecting the SCENE templates Creating your original SCENE templates 3 You can create your original SCENE templates for each SCENE button. You can refer to the preset 18 SCENE templates to create the original SCENE templates. Select the desired SCENE template Create an original SCENE template • INPUT: • MODE: The input source component. The active sound field programs, STRAIGHT or Pure Direct mode. • NIGHT: The night listening mode (see page 49). SYSTEM: Keeps the current night listening mode.
PLAYBACK Playback Caution Extreme caution should be exercised when you play back CDs encoded in DTS. If you play back a CD encoded in DTS on a DTS-incompatible CD player, you will only hear some unwanted noise that may damage your speakers. Check whether your CD player supports CDs encoded in DTS. Also, check the sound output level of your CD player before you play back a CD encoded in DTS. y 3 Start playback on the selected source component or select a broadcast station.
Playback Selecting the front speaker set ■ A quick guide to contents When you want to...
Playback Selecting audio input jacks (AUDIO SELECT) Displaying the current status of this unit on a video monitor This unit comes with a variety of input jacks. Use this feature (audio input jack select) to switch between input jacks when more than one input jack is assigned to as the same input source. You can display the operating information of this unit on a video monitor. 1 Turn on the video monitor connected to this unit.
Playback Using your headphones Playing video sources in the background of an audio source Connect a pair of headphones with a stereo analog audio cable plug to the PHONES jack on the front panel. VOLUME SPEAKERS EDIT SEARCH MODE PRESET/TUNING FM/AM CATEGORY A/B/C/D/E PRESET/TUNING/CH MEMORY DISPLAY TUNING AUTO/MAN'L ZONE 2 ON/OFF Press the input selector buttons ( ) on the remote control to select a video source and then an audio source.
Playback 4 Press SET MENU on the remote control again to exit from “SET MENU”. ■ Audio information FORMAT Signal format. When this unit cannot detect a digital signal, it automatically switches to analog input. SAMPLING The number of samples per second taken from a continuous signal to make a discrete signal. The number of source channels in the input signal (front/surround/LFE). For example, a multi-channel soundtrack with 3 front channels, 2 surround channels and LFE, is displayed as “3/2/0.1”.
SOUND FIELD PROGRAMS Sound field programs This unit is equipped with a variety of precise digital decoders that allow you to enjoy multi-channel playback from almost any stereo or multi-channel sound source. This unit is also equipped with a Yamaha digital sound field processing (DSP) chip containing several sound field programs which you can use to enhance your playback experience.
Sound field programs ■ For audio music sources y For audio music sources, we also recommend using the Pure Direct mode (see page 48). Notes • The available sound field parameters differ depending on the settings of the speakers. • “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 72).
Sound field programs ■ For various sources Notes • The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit. • “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 72). ENTERTAIN 3 ENTERTAINMENT Sports This program allows the listeners to enjoy stereo sport broadcasts and studio variety programs with enriched live feeling.
Sound field programs ■ For movie sources y You can select the desired decoder used with following sound field program (except “Mono Movie”). See page 66 for details. Notes • The available sound field parameters and the created sound fields differ depending on the input sources and the settings of this unit. • “DIALG.LIFT” is available only when “EXTRA SP ASSIGN” in “SPEAKER SET” is set to “PRESENCE” (see page 72).
Sound field programs ■ Stereo playback Note The available parameters differ depending on the input sources and the settings of this unit. STEREO 5 STEREO 2ch STEREO Use this program to mix down multi-channel sources to 2 channels. See page 49 for details. DIRECT STEREO 5 STEREO 7ch STEREO HiFi DSP Use this program to output sound from all speakers. When you play back multi-channel sources, this unit downmixes the source to 2 channels, and then outputs the sound from all speakers.
Sound field programs Enjoying unprocessed input sources (Straight decoding mode) When this unit is in the “STRAIGHT” mode, 2-channel stereo sources are output from only the front left and right speakers. Multi-channel sources are decoded straight into the appropriate channels without any additional effect processing. Press E STRAIGHT (or STRAIGHT) to select “STRAIGHT”.
USING AUDIO FEATURES Using audio features y Before performing operations, set the operation mode selector on the remote control to AMP. Enjoying pure hi-fi sound Use the Pure Direct mode to enjoy the pure high fidelity sound of the selected source. When the Pure Direct mode is activated, this unit plays back the selected source with the least circuitry. Press G PURE DIRECT (or PURE DIRECT) to turn the Pure Direct mode on or off.
Using audio features Enjoying multi-channel sources in 2-channel stereo You can mix down multi-channel sources to 2 channels and enjoy playback in 2-channel stereo. Press STEREO on the remote control repeatedly to select “2ch Stereo”. y Notes • You cannot use the night listening modes in the following cases: –when the Pure Direct mode (see page 48) is selected. –when the component connected to the MULTI CH INPUT jacks is selected as the input source (see page 38).
FM/AM TUNING FM/AM tuning There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use the automatic and manual preset tuning features to store up to 40 stations (A1 to E8: 8 preset station numbers in each of the 5 preset station groups).
FM/AM tuning Notes Automatic preset tuning • Any stored station data existing under a preset station number is cleared when you store a new station under the same preset station number. • If the number of received stations does not reach 40 (E8), automatic preset tuning automatically stops after searching for all the available stations. • Only FM stations with sufficient signal strength are stored automatically by automatic preset tuning.
FM/AM tuning 4 Press 5 PRESET/TUNING/CH l / h to select a preset station number (1 to 8) while the MEMORY indicator is flashing. • Press 5 h to select a higher preset station number. • Press 5 l to select a lower preset station number. 2 Flashes Press 5 PRESET/TUNING/CH l / h on the front panel (or PRESET/CH k / n on the remote control) to select the desired preset station number (1 to 8). The preset station group and number appear in the front panel display along with the station band and frequency.
XM SATELLITE RADIO TUNING XM Satellite Radio tuning XM Satellite Radio offers an extraordinary variety of commercial-free music, plus the best in sports, news, talk and entertainment. XM is broadcast in superior digital audio from coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
XM Satellite Radio tuning Activating XM Satellite Radio Once you have installed the XM Mini-Tuner Dock, inserted the XM Mini-Tuner, connected the XM Dock to your XM Ready® home audio system, and installed the antenna, you are ready to subscribe and begin receiving XM programming. There are three places to find your eight character XM Radio ID: on the XM Mini-Tuner, on the XM Mini-Tuner package, and on XM Channel 0. Record the Radio ID in the following eight squares for reference.
XM Satellite Radio tuning Before performing operations, set the operation mode selector on the remote control to SOURCE. 3 ■ All Channel Search mode 1 2 Press 2 SEARCH MODE (or SRCH MODE) repeatedly to select “ALL CH SEARCH”. Press 5 PRESET/TUNING/CH l / h (or PRESET/CH k / n) repeatedly to search for a channel within all channels. y ■ Category Search mode 1 2 3 Press 2 SEARCH MODE (or SRCH MODE) repeatedly to select “CAT SEARCH”.
XM Satellite Radio tuning Setting the XM Satellite Radio preset channels 4 You can use this feature to store up to 40 XM Satellite Radio channels (A1 to E8: 8 preset channel numbers in each of the 5 preset channel groups). You can then recall any preset channel easily by selecting the preset channel group and number as described in “Preset Search mode” on page 55.
XM Satellite Radio tuning Displaying the XM Satellite Radio information You can display the XM Satellite Radio information (such as channel number, channel name, category, artist name, or song title) for the currently selected channel in the front panel display or in the OSD. y • The front panel display can indicate up to 14 alphanumeric characters at once.
USING IPOD™ Using iPod™ Once you have stationed your iPod in a Yamaha iPod universal dock (such as the YDS-10, sold separately) connected to the DOCK terminal of this unit (see page 23), you can enjoy playback of your iPod using the supplied remote control. You can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts (such as the MP3 format) stored on your iPod (see page 46).
Using iPod™ 1 Set the operation mode selector to SOURCE and then press DISPLAY on the remote control. The following display appears in the OSD.
RECORDING Recording Recording adjustments and other operations are performed from the recording components. Refer to the operating instructions for those components. Caution The DTS signal is a digital bitstream. Attempting to digitally record the DTS bitstream will result in noise being recorded. Therefore, if you want to use this unit to record sources encoded in DTS, the following considerations and adjustments need to be made.
ADVANCED SOUND CONFIGURATIONS Advanced sound configurations Changing sound field parameter settings 4 You can enjoy good quality sound with the initial factory settings. Although you do not have to change the initial factory settings, you can change some of the parameters to better suit the input source or your listening room. PARAMETER Cursor Note You cannot change the sound field parameter values when “MEMORY GUARD” in “OPTION MENU” is set to “ON” (see page 82).
Advanced sound configurations ■ Basic configuration of sound field programs y To change sound field parameter settings, see page 61 for details. Adjusting the vertical dialogue position (DIALG.LIFT) Use this feature to adjust the vertical position of the dialogues in movies. The ideal position of the dialogues is at the center of the video monitor screen. Each sound field program has some parameters defining the characteristics of the program.
Advanced sound configurations ■ Sound field parameters for the advanced configurations Use the following sound field parameters to customize sound field programs in detail. y To change sound field parameter settings, see page 61 for details. Sound field parameter Initial delay. Presence, surround, and surround back sound field initial delay. Changes the apparent distance from the source sound by adjusting the delay between the direct sound and the first reflection heard by the listener.
Advanced sound configurations Sound field parameter ROOM SIZE P.ROOM SIZE S.ROOM SIZE SB ROOM SIZE Features Room size. Presence, surround, and surround back room size. Adjusts the apparent size of the surround sound field. The larger the value, the larger the surround sound field becomes. As the sound is repeatedly reflected around a room, the larger the hall is, the longer the time between the original reflected sound and the subsequent reflections.
Advanced sound configurations Sound field parameter REV.TIME Features Reverberation time. Adjusts the amount of time taken for the dense, subsequent reverberation sound to decay by 60 dB at 1 kHz. This changes the apparent size of the acoustic environment over an extremely wide range. Set a longer reverberation time for “dead” sources and listening room environments, and a shorter time for “live” sources and listening room environments. Control range: 1.0 to 5.
Advanced sound configurations Sound field parameter 2ch Stereo DIRECT Features 2-channel stereo direct. Bypasses the decoders and the DSP processors of this unit for pure hi-fi stereo sound when playing 2-channel analog sources. Choices: AUTO, OFF y • Select “AUTO” to bypass the decoders, the DSP processors and the tone control circuitry only when “BASS” and “TREBLE” are set to 0 dB (see page 48).
Advanced sound configurations ■ Decoder descriptions Category of the program Name of the program SURROUND DECODE PL IIx Music PL II Music Remote control button SUR.DECODE 9 Dolby Pro Logic IIx (or Dolby Pro Logic II) processing for music sources. The Pro Logic IIx decoder is not available when “SB L/R SP” is set to “NONE” (see page 73). PANORAMA DIMENSION CENTER WIDTH Program description Available sound field parameters (see page 63) SUR.
Advanced sound configurations Decoder parameter descriptions Decoder parameter Features PRO LOGIC IIx Music PRO LOGIC II Music PANORAMA Pro Logic IIx Music and Pro Logic II Music panorama. Sends stereo signals to the surround speakers as well as the front speakers for a wraparound effect. PRO LOGIC IIx Music PRO LOGIC II Music DIMENSION Pro Logic IIx Music and Pro Logic II Music dimension. Adjusts the sound field either towards the front or towards the rear.
CUSTOMIZING THIS UNIT (MANUAL SETUP) Customizing this unit (MANUAL SETUP) You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. ■ Auto setup AUTO SETUP Use this feature to automatically adjust speaker and system parameters (see page 28).
Customizing this unit (MANUAL SETUP) Option menu 3 OPTION MENU Use this menu to manually adjust the optional system parameters. Parameter Features Page A)DISPLAY SET Adjusts the brightness of the display and converts video signals. 81 B)MEMORY GUARD Locks sound field program parameters and other “SET MENU” settings. 82 C)AUDIO SELECT Designates the default audio input jack select setting for the input sources when you turn on the power of this unit. 82 D)PARAM.
Customizing this unit (MANUAL SETUP) Using SET MENU 3 Use the remote control to access and adjust each parameter. y • You can change the “SET MENU” parameters while this unit is reproducing sound. • Press RETURN to return to the previous menu level. 1 MANUAL SETUP MANUAL SETUP 1 SOUND MENU 1/2 . A)SPEAKER SET B)SPEAKER LEVEL C)SP DISTANCE D)EQUALIZER E)LFE LEVEL [ ]/[ ]:Up/Down [ENTER]:Enter p . ;AUTO SETUP ;MANUAL SETUP .A;SIGNAL INFO 2/2 [ ]/[ ]:Up/Down [ENTER]:Enter p 4 1 SOUND MENU .
Customizing this unit (MANUAL SETUP) 1 SOUND MENU Use this feature to manually adjust speaker settings or compensate for video signal processing delays when using LCD monitors or projectors. Most of the SOUND MENU parameters are set automatically when you run AUTO SETUP (see page 28). MANUAL SETUP MANUAL SETUP 1 SOUND MENU 1/2 1 SOUND MENU 2/2 . F)DYNAMIC RANGE G)AUDIO SET H)HDMI SET I)EXTD SUR. p [ ]/[ ]:Up/Down [ENTER]:Enter p p p .
Customizing this unit (MANUAL SETUP) Woofer section of a speaker is 16 cm (6.5 in) or larger: large Woofer section of a speaker is smaller than 16 cm (6.5 in): small Surround left/right speakers SUR. L/R SP Choices: NONE, SML, LRG Front speakers FRONT SP Choices: SMALL, LARGE SOUND MENU SOUND MENU FRONT SP SMALL >LARGE SUR. L/R SP NONE >SML LRG When the front speakers are large Select “LARGE” (large). When the surround speakers are large Select “LRG” (large).
Customizing this unit (MANUAL SETUP) LFE/Bass out LFE/BASS OUT Use this feature to select the speakers that output the LFE (low-frequency effect) and the low-frequency signals. Choices: SWFR, FRNT, BOTH Subwoofer phase SUBWOOFER PHASE Use this feature to switch the phase of your subwoofer if bass sounds are lacking or unclear.
Customizing this unit (MANUAL SETUP) ■ Speaker distance C)SP DISTANCE ■ Equalizer D)EQUALIZER Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time.
Customizing this unit (MANUAL SETUP) Center graphic equalizer CENTER GEQ Use to match the tonal quality of the center speaker with that of the front left and right speakers. You can adjust 5 frequency bands (100 Hz, 300 Hz, 1 kHz, 3 kHz and 10 kHz). Control range: –6.0 to +6.0 dB Control step: 0.5 dB SOUND MENU 0dB 0dB 0dB 0dB 0dB p p TEST >OFF ON -______+ .
Customizing this unit (MANUAL SETUP) Maximum volume MAX VOL. Use this feature to set the maximum volume level in the main zone. This feature is useful to avoid the unexpected loud sound by mistake. For example, the original volume range is 16.5 dB to –80.0 dB. However, when “MAX VOL.” is set to –5.0 dB, the volume range becomes –5.0 dB to –80.0 dB. Control range: 16.5 dB, 15.0 dB to –30.0 dB Control step: 5.
Customizing this unit (MANUAL SETUP) y Use this feature to activate the desired decoder manually when this unit cannot detect the signal flag encoded to the input sources correctly. Notes Use this menu to reassign the input/output jacks, select the input mode or rename the input source. MANUAL SETUP 2 INPUT MENU p .
Customizing this unit (MANUAL SETUP) For OPTICAL OUTPUT jack 1 OPTICAL OUT Choices: (1) PHONO, CD, MD/CD-R, DVD, DTV/CBL, V-AUX, VCR, DVR For HDMI IN jacks 1 and 2 HDMI IN Choices: [IN1] DVD, DTV/CBL, V-AUX, DVR, VCR [IN2] DVD, DTV/CBL, V-AUX, DVR, VCR INPUT MENU INPUT MENU HDMI IN . [IN1];;; DVD ( DVD ) [IN2];;;DTV/CBL (DTV/CBL)) OPTICAL OUT .
Customizing this unit (MANUAL SETUP) C)VOLUME TRIM MY DVD DVD -> 0.0dB [[]/[[]:Adjust [RETURN]:Exit y • You can adjust the value for DOCK only when iPod is stationed to the Yamaha Universal Dock connected to this unit. • The default name (“DVD” in the display example above) and the new name (“MY DVD”) of the selected input source appears in the OSD. ■ Decoder mode D)DECODER MODE INPUT MENU D)DECODER MODE .
Customizing this unit (MANUAL SETUP) 3 OPTION MENU Use this menu to adjust the optional system parameters. MANUAL SETUP 3 OPTION MENU MANUAL SETUP 1/2 . A)DISPLAY SET B)MEMORY GUARD C)AUDIO SELECT D)PARAM. INI 3 OPTION MENU 2/2 . E)ZONE2 SET F)XM RADIO SET G)DOCK SET p p p p [ ]/[ ]:Up/Down [ENTER]:Enter [ ]/[ ]:Up/Down [ENTER]:Enter ■ Display settings A)DISPLAY SET OPTION MENU A)DISPLAY SET . DIMMER;;;;;;;;;0 VIDEO CONV.;;;ON OSD SHIFT;;;;;;0 1/2 A)DISPLAY SET 2/2 .
Customizing this unit (MANUAL SETUP) ■ Memory guard B)MEMORY GUARD Use this feature to prevent accidental changes to DSP program parameter values and other system settings. Choices: OFF, ON OPTION MENU B)MEMORY GUARD >OFF ON [[]/[[]:Select [ENTER]:Return • Select “OFF” to turn off the “MEMORY GUARD” feature. • Select “ON” to protect: – sound field program parameters – all “SET MENU” items – all speaker levels – SCENE template parameters ■ Parameter initialization D)PARAM.
Customizing this unit (MANUAL SETUP) Zone 2 Initial volume INI VOL. Use this feature to set the volume level of Zone 2 when the power of this unit is turned on. Choices: Off, –80.0 dB to +16.5 dB Control step: 0.5 dB Notes • The “MAX VOL.” setting takes priority over the “INI VOL.” setting. • When you select “FRONT B”, “PRNS” or “NONE” in “EXTRA SP ASSIGN” (see page 72), “Zone 2 SP Not Assigned” appears in the OSD and the “ZONE2 SET” parameter is not available. • The “INI VOL.
REMOTE CONTROL FEATURES Remote control features In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code for each input source (see page 87).
Remote control features Controlling this unit, a TV, or other components ■ Controlling this unit ■ Controlling a TV Set the operation mode selector to AMP to control this unit. Set the operation mode selector to TV to control your TV. To control your TV, you must set the appropriate remote control code for DTV/CBL or PHONO (see page 87). When you set the remote control codes for both DTV/CBL and PHONO, priority is given to the one set for DTV/CBL.
Remote control features ■ Controlling other components Set the operation mode selector to SOURCE to control other components selected with the input selector buttons. You must set the appropriate remote control code for each input source in advance (see page 87). The following table shows the function of each control button used to control other components assigned to each input selector button. Be advised that some buttons may not correctly operate the selected component.
Remote control features Setting remote control codes 1 You can control other components by setting the appropriate remote control codes. For a complete list of available remote control codes, refer to “List of remote control codes” at the end of this manual. Press one of the input selector buttons ( ) on the remote control to select the input area you want to set up.
Remote control features Resetting all remote control codes Use this feature to clear all the remote control codes previously set and reset all of them to the initial factory settings. 1 Press CODE SET using a ballpoint pen or a similar object. The TRANSMIT indicator on the remote control flashes twice. TRANSMIT TRANSMIT CODE SET POWER POWER TV AV STANDBY POWER Flashes 2 Press the numeric buttons ( ) to enter the code number “9981”.
USING MULTI-ZONE CONFIGURATION Using multi-zone configuration This unit allows you to configure a multi-zone audio system. The Zone 2 feature allows you to set this unit to reproduce separate input sources in the main zone and the second zone (Zone 2). You can control this unit from the second zone using the supplied remote control. Only analog signals are sent to the second zone. Any source you want to listen to in the second zone must be connected to the analog AUDIO IN jacks of this unit.
Using multi-zone configuration ■ Using the internal amplifier of this unit Important safety notice The EXTRA SP speaker terminals of this Receiver should not be connected to a Passive Loudspeaker Selector Box or more than one loudspeaker per channel. Connection to a Passive Loudspeaker Selector Box or multiple speakers per channel could create an abnormally low impedance load resulting in amplifier damage. See this owner’s manual for correct usage.
Using multi-zone configuration Operate the following operations after activating the Zone 2 operation mode. ■ Controlling Zone 2 with the remote control Operating Zone 2 Turning on Zone 2 Rotate the I INPUT selector to select the desired input source while the ZONE2 indicator is flashing in the front panel display. Press and hold POWER or STANDBY and then press to set the remote control to the Zone 2 mode. • Select “TUNER” as the input source to use the TUNER features in Zone 2.
ADVANCED SETUP Advanced setup This unit has additional menus that are displayed in the front panel display. The advanced setup menu offers additional operations to adjust and customize the way this unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening environment. Notes • The settings you make are reflected next time you press B MASTER ON/OFF inward to the ON position to turn on this unit (see page 25).
Advanced setup See page 92 for the operation of the advanced setup. ■ Speaker impedance SP IMP. Use this feature to set the speaker impedance of this unit so that it matches that of your speakers. Choices: 8: MIN, 6: MIN • Select “ : MIN” to set the speaker impedance to 8 : . • Select “6: MIN” to set the speaker impedance to 6 : . SP IMP. Speaker Impedance level If you use one set (A or B), the impedance of each speaker must be 8 : or higher.
Advanced setup ■ Remote control XM ID REMOTE XM (U.S.A. and Canada models only) See page 92 for the operation of the advanced setup. ■ Remote control TUNER ID REMOTE TUN Use this feature to set the TUNER ID of this unit for remote control recognition. Choices: ID1, ID2 • Select “ID1” when the remote control TUNER ID code is set to “82005”. • Select “ID2” when the remote control TUNER ID code is set to “81949”.
Advanced setup See page 92 for the operation of the advanced setup. ■ SCENE IR code setting SCENE IR Use this feature to output the remote control signals at the REMOTE OUT jack automatically when this unit is in the SCENE mode. Choices: ON, OFF • Select “ON” when the component connected to the REMOTE OUT jack is the Yamaha component and has the capability of the SCENE control signals. This unit automatically sends the remote control signals to the component.
TROUBLESHOOTING Troubleshooting Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. ■ General Problem This unit fails to turn on or enters the standby mode soon after the power is turned on. No sound. No picture.
Troubleshooting Problem The sound suddenly goes off. Sound is heard from the speaker on one side only. Cause The protection circuitry has been activated because of a short circuit, etc. Remedy See page Check that the speaker impedance setting is correct. 25, 93 Check that the speaker wires are not touching each other and then turn this unit back on. — The sleep timer has turned this unit off. Turn this unit on, and play the source again. — The sound is muted.
Troubleshooting Problem No sound is heard from the subwoofer. Cause Remedy See page “LFE/BASS OUT” in “SET MENU” is set to “FRONT” when a Dolby Digital or DTS signal is being played. Set “LFE/BASS OUT” to “SWFR” or “BOTH”. 72 “LFE/BASS OUT” in “SET MENU” is set to “SWFR” or “FRONT” when a 2channel source is being played. Set “LFE/BASS OUT” to “BOTH”. 72 The source does not contain lowfrequency signals. Dolby Digital or DTS sources cannot be played.
Troubleshooting Problem Cause Remedy See page “CHECK SP WIRES” appears in the front panel display. Speaker cables are short-circuited. Make sure all speaker cables are connected correctly. 13 There is noise interference from digital or radio frequency equipment. This unit is too close to the digital or highfrequency equipment. Move this unit further away from such equipment. — The picture is disturbed. The video source uses scrambled or encoded signals to prevent dubbing.
Troubleshooting ■ XM Satellite Radio If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel display. In this case, read the cause and follow the corresponding remedies. Status message Cause Remedy See page CHECK ANTENNA The XM Mini-Tuner and XM Dock are not connected to the XM jack of this unit or do not work properly. Check XM Mini-Tuner and XM Dock connections and orient for the best reception level.
Troubleshooting ■ HDMI Error message Cause Remedy See page DEVICE OVER The number of the connected HDMI components is over the limit. Reduce the number of the connected HDMI components. — HDCP ERROR HDCP authentication failed. Check that the connected HDMI components support the HDCP copy protection standards. — ■ iPod Note In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod (see page 23).
Troubleshooting During AUTO SETUP Error message Cause Remedy See page E-1:NO FRONT SP Front L/R channel signals are not detected. Check the front L/R speaker connections. 13 E-2:NO SUR SP A surround channel signal is not detected. Check the surround speaker connections. 13 E-3:NO PRNS SP A presence channel signal is not detected. Check the presence speaker connections. 13 E-4:SBR->SBL Only a right surround back channel signal is detected.
RESETTING THE SYSTEM Resetting the system Use this feature to reset all the parameters of this unit to the initial factory settings. Notes • This procedure completely resets all the parameters of this unit including the “SET MENU” parameters. However, the advanced setup menu parameters will not be initialized. • The initial factory settings are activated next time you turn on this unit.
GLOSSARY Glossary ■ Bi-amplification connection ■ Dolby Digital EX A bi-amplification connection uses two amplifiers for a speaker. One amplifier is connected to the woofer section of a loudspeaker while the other is connected to the combined mid and tweeter section. With this arrangement each amplifier operates over a restricted frequency range. This restricted range presents each amplifier with a much simpler job and each amplifier is less likely to influence the sound in some way.
Glossary ■ DTS 96/24 ■ Neo:6 DTS 96/24 offers an unprecedented level of audio quality for multi-channel sound on DVD video, and is fully backward-compatible with all DTS decoders. “96” refers to a 96 kHz sampling rate compared to the typical 48 kHz sampling rate. “24” refers to 24-bit word length. DTS 96/ 24 offers sound quality transparent to the original 96/24 master, and 96/24 5.1-channel sound with full-quality fullmotion video for music programs and motion picture soundtracks on DVD video.
SOUND FIELD PROGRAM INFORMATION Sound field program information ■ Elements of a sound field ■ SILENT CINEMA What really creates the rich, full tones of a live instrument are the multiple reflections from the walls of the room. In addition to making the sound live, these reflections enable us to tell where the player is situated as well as the size and shape of the room in which we are sitting.
PARAMETRIC EQUALIZER INFORMATION Parametric equalizer information This unit employs Yamaha Parametric Room Acoustic Optimizer (YPAO) technology, together with the Parametric EQ settings (see page 75), to optimize the frequency characteristics of its parametric equalizer to match your listening environment. YPAO uses a combination of the following three parameters (Frequency, Gain and Q factor) to provide highly precise adjustment of the frequency characteristics.
SPECIFICATIONS Specifications AUDIO SECTION • Volume Control ....................................... MUTE/–80 dB to 16.5 dB • Minimum RMS Output Power for Front, Center, Surround, Surround back 20 Hz to 20 kHz, 0.06% THD, 8 : ...................................... 90 W • Tone Control (Front L/R) BASS Boost/Cut ..................................................... ±10 dB/50 Hz BASS Turnover Frequency ................................................. 350 Hz TREBLE Boost/Cut ...............................
Specifications GENERAL • Power Supply [U.S.A. and Canada models] ............................. AC 120 V, 60 Hz [General model] ....................................... AC 110/120/220/230–240 V, 50/60 Hz [Asia model] ..................................................... AC 220/230–240 V, 50/60 Hz [China model] .................................................... AC 220 V, 50 Hz [Korea model] .................................................... AC 220 V, 60 Hz [Australia model] ...............................
■ Front panel 1 2 3 4 5 6 7 8 9 0 VOLUME SPEAKERS EDIT SEARCH MODE PRESET/TUNING FM/AM CATEGORY A/B/C/D/E l PRESET/TUNING/CH h MEMORY DISPLAY TUNING AUTO/MAN'L ZONE 2 ON/OFF ZONE CONTROL SCENE 2 1 3 4 INPUT PROGRAM MAIN ZONE MASTER PHONES STRAIGHT TONE CONTROL PURE DIRECT AUDIO SELECT VIDEO AUX OPTIMIZER MIC ON/OFF ON A i OFF EFFECT SILENT CINEMA B S VIDEO C D E F G H I J VIDEO L AUDIO R OPTICAL
■ Remote control U V W CODE SET POWER TV AV A POWER STANDBY H MULTI CH IN AUDIO SEL MD CD G TRANSMIT POWER CD-R I CBL DVD DTV TUNER XM DVR VCR PHONO DOCK V-AUX AMP SOURCE TV VOL TV CH VOLUME TV J K P L TV MUTE TV INPUT CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 MUTE CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 STEREO B STEREO ENHANCER STRAIGHT 5 6 7 SUR.
INDEX Index ■ Numerics 1 SOUND MENU, Manual setup ........ 69 2 INPUT MENU, Manual setup .......... 69 2ch Enhancer, Sound field program .... 46 2ch STEREO, Sound field program .... 46 3 OPTION MENU, Manual setup ....... 70 7ch Enhancer, Sound field program .... 46 7ch STEREO, Sound field program .... 46 96/24 indicator ..................................... 27 ■ A A)DISPLAY SET, Option menu ......... 81 A)I/O ASSIGNMENT, Input menu ..... 78 A)SPEAKER SET, Sound menu .........
Index EQ TYPE, Auto setup parameter ......... 29 Equalizer type select, Equalizer ........... 75 Equalizer, Sound menu ........................ 75 EQUALIZING, Auto setup parameter ....................... 30 Extended surround decoders, Sound menu ..................................... 77 External amplifier connection .............. 22 External decoder connection ................ 22 EXTRA SP ASSIGN, Auto setup parameter ....................... 29 EXTRA SP ASSIGN, Speaker settings .............................
Index PL II Movie, Decoder type .................. 67 PL II Music, Decoder type ................... 67 PL LEVEL, Sound field parameter ...... 66 Playing video sources in the background ............................ 40 PLII Movie, Decoder type ................... 66 PLIIx Game, Decoder type .................. 67 PLIIx Movie, Decoder type ........... 66, 67 PLIIx Music, Decoder type .................. 67 Power cable connection ....................... 24 PR LEVEL, Sound field parameter .....
Index Surround left/right speakers, Speaker settings ............................... 73 SURROUND PRE OUT jack connection ........................................ 22 Surround right speaker level, Sound field parameter ...................... 66 Surround sound field initial delay, Sound field parameter ...................... 63 Surround sound field liveness, Sound field parameter ...................... 64 Surround sound field room size, Sound field parameter ......................
List of remote control codes CABLE TV RECEIVER 3M A-MARK ABC 10033 10008, 10144 10237, 10003, 10008, 10033 ACCUPHASE 10003 ACORN 10237 ACTION 10237 ACTIVE 10237 AMERICAST 10899 ARCHER 10237 BCC 10276 BELL SOUTH 10899 BRITISH TELECOM 10003 CENTURY 10008 DIRECTOR 10476 DX ANTENNA 11500 FOSGATE 10276 FUJITSU 11497 GE 10144 GENERAL INSTRUMENT 10476, 10810, 10276, 10003 GIBRALTER 10003 GOLDSTAR 10144 HITACHI 10003, 10008, 10033 INSIGHT 10476, 10810 JERROLD 10476, 10810, 10276, 10003 MACOM 10033 MEMOREX 10000 M
EMERSON 20036, 20047, 20150, 20154, 20170, 20171, 20178, 20179, 20180, 20236, 20451, 20463, 20623 ENVISION 20030 ESA 20171, 20812 FISHER 20000, 20054, 20154 FORTRESS 20093 FUJITSU 20179, 20186, 20683, 20809, 20853, 21181, 21607 FUJITSU GENERAL 20186 FUNAI 20000, 20171, 20179, 20180, 20264, 20342 FUTURETECH 20180 GATEWAY 21755, 21756 GE 20000, 20030, 20047, 20051, 20060, 20178, 20451, 21147, 21347, 21447 GEMINI 20047 GENERAL 20186 GIBRALTER 20000, 20017, 20030 GOLDSTAR 20030, 20036, 20037, 20047, 20054, 201
PHILIPS 20030, 20037, 20054, 20171, 20186, 20690, 21254, 21454, 21455 PILOT 20030, 20051, 20060, 20178 PIONEER 20166, 20679, 20866, 21260 POLAROID 20765, 20865 PORTLAND 20092, 20451 PRECISION 20180, 20236 PRIMA 20761, 20783, 20815, 20817 PRINCETON 20700 PRISM 20051, 20250 PROSCAN 20047, 21347, 21447 PROTEC 20037, 20264 PROTON 20178 PROVISION 20037 PULSAR 20017, 20092 PULSER 20092, 20178 QUARTZ 20150, 20178 QUASAR 20051, 20250, 20650 R-LINE 20037 RABBIT 20047 RADIOSHACK 20030, 20047, 20150, 20154, 20178, 20
VCR A-MARK LXI 30037, 30000, 30042, 30067 M ELECTRONIC 30240 MAGNASONIC 30037, 30240, 30000, 31278 MAGNAVOX 30035, 30037, 30048, 30039, 30081, 30240, 30000, 30226, 30618, 31781 MAGNIN 30240 MARANTZ 30035, 30081, 30038, 31381 MARTA 30037 MATSUI 30037, 30209, 30348 MATSUSHITA 30035, 30162, 30081, 30226 MEDIA CENTER PC 31972 MEDION 30348 MEI 30035 MEMOREX 30035, 30162, 30037, 30048, 30039, 30047, 30240, 30000, 30104, 30209, 30307, 30348, 31237 METZ 30037 MGA 30060, 30240, 30043 MGN TECHNOLOGY 30240 MICROSOFT
SEARS 30060, 30035, 30162, 30037, 30048, 30039, 30047, 30033, 30045, 30000, 30042, 30104, 30067, 30043, 30209, 30041, 30034, 31237 SHARP 30048, 30047, 30032, 30000, 30807, 31285, 31742, 31810 SHINTOM 30039, 30240, 30000 SHOGUN 30240 SIEMENS 30037, 30104 SIGNATURE 30060, 30035, 30037, 30048, 30000 SINGER 30037, 30240 SONIC BLUE 30614, 30616 SONY 30035, 30047, 30032, 30033, 30000, 30067, 30034, 30226, 30636, 31232, 31295, 31296, 31447, 31448, 31636, 31972 SOUNDMASTER 30000 STACK 9 31972 STS 30042 SV2000 3000
REALISTIC REOC RIO ROTEL ROWA SABA SAMPO SAMSUNG LD PLAYER CD PLAYER AIWA CARVER DENON ADC ADCOM AIWA AKAI 40203 40064 40059, 40172, 40241 DISCO VISION FUNAI HITACHI KENWOOD MAGNAVOX MARANTZ MITSUBISHI NAD OPTIMUS PANASONIC PHILIPS PIONEER QUASAR REALISTIC SEGA SHARP SONY TECHNICS TOSHIBA VICTOR WARDS YAMAHA 40023 40203 40023 40236, 40258 40064, 40217, 40241 40064 40059, 40241 40059 40059 40204 40064 40059, 40023, 40241 40204 40203 40023 40001 40193, 40201 40204 40059 40245 40059 40217 DVD RECORDER
CD RECORDER CLASSIC 71297 DENON 70626 FISHER 71325 GPX 71296 HARMAN/KARDON 71202 JVC 71294 KENWOOD 70626 LG 71208 MARANTZ 70626 PHILIPS 70626 PIONEER 71062, 71087 RCA 70053 SONY 70000, 70100, 71364 TDK 71208 YAMAHA 70888, 71292 MD RECORDER DENON KENWOOD ONKYO OPTIMUS PANASONIC PIONEER SHARP SHERWOOD SONY YAMAHA 70873 70681, 70826, 71683 70868, 71685 71063 71682 71063 70861, 71684 71067 70490, 71790 70490, 70888, 72001 TAPE DECK AIWA DENON 70197 70076, 70371, 70412 GARRARD 70308, 70309 JVC 70244, 70273 K
© 2007 YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND YAMAHA SCANDINAVIA A.B.
U RX-V861/RX-V661 ■ Front panel 2 1 3 4 5 6 7 8 0 9 VOLUME SPEAKERS EDIT SEARCH MODE PRESET/TUNING FM/AM CATEGORY A/B/C/D/E l PRESET/TUNING/CH h MEMORY DISPLAY TUNING AUTO/MAN'L ZONE 2 ON/OFF ZONE CONTROL SCENE 2 1 3 4 INPUT PROGRAM MAIN ZONE MASTER PHONES STRAIGHT TONE CONTROL PURE DIRECT AUDIO SELECT VIDEO AUX OPTIMIZER MIC ON/OFF ON A OFF EFFECT SILENT CINEMA B S VIDEO C D E F G H I J VIDEO L AUDIO R OPTICAL
■ Remote control U V W CODE SET POWER POWER TV AV CD CD-R POWER STANDBY H MULTI CH IN AUDIO SEL MD A G TRANSMIT I CBL DVD DTV TUNER XM DVR VCR PHONO DOCK V-AUX AMP SOURCE TV VOL TV CH VOLUME TV J K P L TV MUTE TV INPUT CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 MUTE CLASSICAL LIVE/CLUB ENTERTAIN MOVIE 1 2 3 4 STEREO B STEREO ENHANCER STRAIGHT 5 6 7 SUR.
U RX-V661 Page 35 (footnote *2) Incorrect *2 You can select “V-AUX” as the input source even if your iPod is stationed in the Yamaha Universal Dock connected to this unit. When the SCENE mode is deactivated and your iPod is stationed in the Yamaha Universal Dock, this unit selects “DOCK” as the input source automatically. Correct *2 You can select “V-AUX” as the input source even if your iPod is stationed in the Yamaha Universal Dock connected to this unit.
OYAMAHA Registering Your New Yamaha Product is Fast and Easy Thank you for purchasing a new product from Yamaha Electronics.We'd like to continue providing you with high quality products and better service. So, we've made it simple to register your new product purchase online. Please take a few minutes- to visit our website at www.yamaha.comIYEC/registration/ and complete the information and questions included there.We appreciate your business and we look forward to hearing from you.
YAMAHA Home Audio products are designed and manufactured to provide a high level of trouble-free performance. YAMAHA Electronics Corporation, USA, is proud of the experienced craftsmanship that goes into each and every YAMAHA Home Audio product. YAMAHA sells its Home Audio products only through a network of high quality, specially authorized dealers and is pleased to offer the following Limited Warranty, which applies only to products purchased from our authorized dealers.
