Owner's Manual

Only the center
speaker outputs
substantial sound.
No sound Is heard
from the center
speaker.
No sound Is heard
from the presence
speakers.
When playing a monaural source with a
sound field program, the source signal is
directed to the center channel, and the front
and surround speakers output effect
sounds.
"CENTER SP" in "SET MENU" is set to
"NONE".
One of the sound field programs (except
for "7ch Stereo")
has been selected.
The sound field programs are turned off.
You are using a source or program
combination
that does not output sound
from all channels.
"EXTRA SP ASSIGN" is set to a setting
other
than "PRESENCE".
Set "CENTER SP" to "SMALL" or "LARGE".
Try another
sound field program.
Press @STRAIGHT to tum them on.
Try another sound field program.
Set "EXTRA SP ASSIGN" to "PRESENCE".
Troubleshootmg
86
48
51
42
85
No sound Is heard
from the surround
speakers.
No sound is heard
from the surround
back speakers.
Zone 2 speaker
settings are not
available in "SET
MENU".
FRONT B speakers
cannot be activated.
No sound from the
center, surround or
surround back
speakers when the
FRONT B speakers are
activated.
Presence speaker
settings are not
available In "SET
MENU".
No sound Is heard
from the subwoofer.
"SUR. LlR SP" in "SET MENU" is set to
"NONE".
This unit
is in the "STRAIGHT" mode and
a monaural source is being played back.
"SUR. UR SP" in "SET MENU" is set to
"NONE" and "SUR.B UR SP" is
automatically set to "NONE".
"SUR.B
UR SP" in "SET MENU" is set to
"NONE".
"EXTRA SP ASSIGN" is set to a setting
other
than "ZONET.
"EXTRA SP ASSIGN" is set to a setting
other
than "FRONT B".
"EXTRA SP ASSIGN" is set to
"ZONEB".
"EXTRA SP ASSIGN" is set to a setting
other
than "PRESENCE".
"LFEIBASS
OUT' in "SET MENU" is set
to "FRONT' when a Dolby Digital or DTS
signal
is being played.
"LFEIBASS
OUT' in "SET MENU" is set
to "SWFR" or "FRONT' when a
2-channel
source is being played.
The source does not contain low-frequency
Set "SUR. LlR SP" to "SML" or "LRG".
Press @STRAIGHT on the front panel so that
"STRAIGHT" disappears from the front panel display.
Set "SUR UR SP" and "SURB UR SP" to a setting
other
than "NONE".
Set "SURB LlR SP" to a setting other than "NONE".
Set "EXTRA SP ASSIGN" to "ZONE2".
Set "EXTRA SP ASSIGN" to "FRONT B".
Set "EXTRA SP ASSIGN" to "FRONT B".
Set "EXTRA SP ASSIGN" to "PRESENCE".
Set "LFEJBASS OUT' to "SWFR" or "BOTH".
Set "LFEJBASS OUT' to "BOTH".
86
51
86
86
85
85
85
85
85
85
Make an appropriate setting following the operating
instructions for your
component.
signals.
Dolby Digital or DTS The connected component is not set to
sources cannot be output Dolby Digital or DTS digital
played. (Dolby Digital signals.
or DTS Indicator in the -A--:..ud-i-o-:"jn-p-u-t-ja-c-k-se--:l-ec-t-:"is-s-e-t-to-----S-e-t-A-u-d-io-j-n-pu-t-ja-c-k-s-e-le-ct-t-o-"-A-U-T-O-'-, .-------44---
front panel display "ANALOG".
does not light up.)
A humming sound Is
heard.
The volume level
cannot be increased,
or the sound is
distorted.
The sound effects
cannot be recorded.
Incorrect cable connections.
The component connected to the AUDIO
OUT (REC) jacks
of this unit is turned off.
It is not possible to record the sound effects
with a recording
component.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
Tum on the power of the component.
111 En
I