Owner's Manual
Table Of Contents
- Owners Manual
- Reset
- Table of Contents
- Features
- HDMI Information
- Supplied Accessories
- Parts & Controls
- Connections
- Getting Started
- Basic Operation
- Advanced Setup / Menu Operation
- Remote Control Operation
- Troubleshooting
- Glossary
- Specs
- Remote Control Codes
- Index
- Correction to Manual
- Front Panel Diagram
- Remote Control Diagram
- XM Channel Guide
- Warranty
ate/lite
Radio
™
tunin
Before performing the following operations, press (@SIRIUS
on the remote control.
• All Channel Search mode
1 Press @SEARCH MODE (or @SRCH
MODE) repeatedly
to
select"
ALL
CH
SEARCH".
2 Press
@PRESETITUNING/CH
<J
II>
(or
@PRESET/CH
111
'1/)
repeatedly
to
search
for a channel within all channels.
~'4<':.
•
You
can search
for
a channel quickly
by
pressing and holding
@PRESETfTUNINGICH
<l
/
t>
(or @PRESET/CH
b.
/'il).
•
You
can skip channels to the previous
or
next category
by
pressing @CATEGORY (or @A-ElCAT.
<l
/
t».
• Category Search mode
1 Press @SEARCH MODE (or @SRCH
MODE) repeatedly
to
select "CAT SEARCH".
2 Press @CATEGORY (or @A-E/CAT.
<J
11»
repeatedly
to
change the channel category.
3 Press
@PRESETITUNING/CH
<J
II>
(or
@PRESET/CH
111
'1/)
repeatedly
to
search
for a channel within the selected channel
category•
•
0,
~<i>~
You
can search for a channel quickly by pressing and holding
@PRESETfTUNING/CH
<l
/
I>
on the front panel (or
@PRESET/CH
b.
/
'1/
on the remote control).
;stl~~I~
This unit skips the channels when this unit
is
All Channel Search
mode
or
Category Search mode
in
the following cases (it is not
malfunction
of
this unit):
- the channel is locked (see page 65).
- the channel
is
out
of
service.
- you do not subscribe to the channel.
64 En
• Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset SIRIUS channels. For details, see
"Setting the SIRIUS Satellite
Radio™
preset channels"
on
page 65.
1 Press
@SEARCH
MODE (or @SRCH
MODE) repeatedly
to
select "PRESET
SEARCH".
2 Press @CATEGORY (or @A-E/CAT.
<J
11»
repeatedly
to
change the preset channel
group (A
to
E).
3 Press
@PRESETITUNING/CH
<J
II>
(or
@PRESET/CH
111
'1/)
repeatedly
to
change
the preset channel number
(1
to
8).
.0,
~<i>~
You
can also select the preset channel number directly by
pressing the numeric buttons
(I
to 8)
(@).
• Direct number access mode
1 Press @SRCH MODE on the remote control
repeatedly
to
select"
ALL
CH
SEARCH"
or
"CAT SEARCH".
2 Press the numeric buttons (@)
to
enter the
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons
(@)
as shown below.
.:'¥:.
•
To
display the Sirius ID number displayed in the front panel
display, select channel "0".
• To enter a one-digit
or
two-digit channel number, press the
numeric buttons
(@)
on the remote control and then press
~ENT
to confirm the input number.
• Instead
of
pressing
~ENT
to tune into the channel
immediately, you can wait a few seconds until this unit confirms
the entered channel number.
• If no button
is
pressed within a few seconds after you enter a
one-digit
or
two-digit number, this unit automatically confirms
the entered channel number.
•
If
the selected channel
is
locked, "PIN: " appears
in
the front
panel display. Enter the four-digit Parental Lock code number
by
using the numeric buttons
(@)
or press
~ENT
to cancel
(see page 65).