ZH
SPECIAL MESSAGE SECTION PRODUCT SAFETY MARKINGS: Yamaha electronic products may have either labels similar to the graphics shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK).
Explanation of Graphical Symbols CAUTION The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
注意事项 请在操作使用前,首先仔细阅读下述内容 * 请将本说明书存放在安全的地方,以便将来随时参阅。 警告 为了避免因触电、短路、损伤、火灾或其它危险可能导致的严重受伤甚至死亡,请务必遵守下列基本注意事 项。这些注意事项包括但不限于下列情况: 电源 / 电源线 关于潮湿的警告 ● 只能使用本设备所规定的额定电压。所要求的电压被印在本设 备的铭牌上。 ● 定期检查电插头,擦除插头上积起来的脏物或灰尘。 ● 只能使用提供的电源线 / 插头。 ● 请勿将电源线放在热源如加热器或散热器附近,不要过分弯折 或损伤电源线,不要在其上加压重物,不要将其放在可能被踩 踏引起绊倒或可能被碾压的地方。 ● 请务必连接到带有保护接地连接的适当电源插座。接地不当可 能引起触电。 ● 请勿让本设备淋雨或在水附近及潮湿环境中使用,或将盛有液 体的容器放在其上,否则可能会导致液体溅入任何开口。如果 任何液体如水渗入本乐器,请立即切断电源并从 AC 电源插座拔 下电源线。然后请有资格的 Yamaha 维修人员对设备进行检修。 ● 切勿用湿手插拔电源线插头。 火警 请勿打开 ● 请勿在乐器上放置燃烧着的物
● 请勿长时间持续在很高或不舒服的音量水平使用本乐器 / 设备或 耳机,否则可能会造成永久性听力损害。若发生任何听力损害 或耳鸣,请去看医生。 ● 连接 将本设备连接到其它设备之前,请关闭所有设备的电源开关。 在打开或关闭所有设备的电源开关之前,请将所有音量都调到 最小。而且,务必将所有元件的音量调到最小值,并且在演奏 乐器时逐渐提高音量,以达到理想的听觉感受。 保存数据 数据保存和备份 维护保养 ● ● 清洁乐器时,使用柔软的干布。请勿使用涂料稀释剂、溶剂、 清洁液或浸了化学物质的抹布。 当您关闭乐器的电源时,会失去 DRAM 数据 (参见参考手册 〈另附的 PDF 文件〉)。把数据保存到闪存 ROM/ 内置闪存 (参 见第 47 页) /USB 存储设备 / 外部设备,比如计算机。 ● 小心操作 ● ● 请勿在面板或键盘上的间隙内插入或掉落纸张、金属或其他物 体。万一发生这种情况,请立即关闭电源,从 AC 电源插座中拔 出电源插头。然后请有资格的 Yamaha 维修人员对设备进行检修。 ● 请勿在乐器上放乙烯或塑料或橡胶物体,否则可能使面板或键 盘脱色。 ● 请勿将身体压在本
鸣谢惠顾 S90 XS/S70 XS研发小组的一封信 感谢您购买Yamaha S90 XS/S70 XS 音乐合成器。 我们隆重推出了S90 ES后续机型,全新的S90 XS/S70 XS。本乐器具有超高质量乐器音质和真实钢琴触感响应,无疑是世 界上各种流派乐手和演奏家的最佳选择。我们设计的这款机型结合了我们在合成器研发领域内多年的经验,它不仅仅适用 于顶尖的专业乐手,也可以供对想获得更高质量、演奏效果和高级功能的业余演奏者和爱好者使用—特别是在现场演奏方 面。为了完成这一系列,我们增加了76键机型的S70 XS,它具有与88键机型相同的键盘触感,同时具有更大的便携性。 然而, S90 XS/S70 XS的高级、便捷功能不仅如此。在远程控制功能和主控键盘功能也进行了改进,功能更为强大,可满 足专业音乐制作的需要。我们坚信, S90 XS/S70 XS在音乐制作方面会对您大有帮助,并且我们相信这款产品会成为您在 音乐布置、现场演奏、录音等等领域中‘首选’的乐器。 为了充分使用S90 XS/S70 XS的功能,请仔细阅读本手册。也建议您将本说明书放置于安全而便捷的地方,以便将来随时 参阅。 我们真诚地希望S90
S90 XS/S70 XS主要功能 大量波形和多种声音选择,包括最优质的钢琴声音 S90 XS/S70 XS具有包括许多最新采样的声音,多达142 MB的超高质量钢琴波形,以及直接从舰旗产品MOTIF XS音乐 制作合成器中获得的多种音色-总计有456 MB的可用声音波形。 平衡力度锤键盘—配备88键和76键两种—具有自然的触感和响应 S90 XS/S70 XS具有高级的平衡力度锤键盘 (带初始力度/触后力度),采用了Yamaha在声学钢琴和合成器研发中所积 累的领先专有技术。使用88键机型可进行全面的钢琴演奏,而较小的76键机型具有更大的便携性、更容易进行运输。 Performance Creator S90 XS/S70 XS的Performance Creator功能,可让您根据喜爱的音色为原创演奏快速、轻松指定层叠/分区/鼓组指定。 您可以利用音色的当前效果和设置,快速组合成原创音色。 直观的面板组成 设计的按钮、旋钮和滑杆布局良好、逻辑性强,可实现最佳的直观操作,特别在现场演奏中。例如,您可以快速选择 一个声部,使用声部开关将其打开/关闭,将琶音开关打开/关闭、打开/关闭琶音保
关于本使用说明书 使用说明书 (本书) 介绍上面板控制旋钮的操作。 PDF文件 (包括使用说明书CD-ROM光盘) 参考手册 详细介绍了有关声音相关参数和效果参数。 Data List 该书包含了各种重要的一览表,如音色一览表,波形一览表、复合音色一览表、 MIDI应用表、演奏组音乐一览表、主 控程序一览表、混音模板一览表、琶音类型一览表和遥控功能一览表。 如何使用PDF说明书 参考手册和Data List以PDF格式的数据文件提供。这些PDF文件可在计算机上查看并阅读。使用Adobe® Reader®查 看PDF文件时,您可以搜索特定词、打印特定页或链接打开手册中所需的章节。浏览PDF文件时,词汇搜索和链接功 能是特别方便的方法,建议您使用这些功能。可以从以下URL下载最新版本的Adobe Reader。 http://www.adobe.
目录 鸣谢惠顾 ............................................................................... 6 附件 ...................................................................................... 6 随 MIDI 文件播放演奏键盘 ............................................. 41 关于附带光盘 ........................................................................ 6 保存编辑过的音色 / 演奏组音色 / 复合音色 .........................43 S90 XS/S70 XS 主要功能 ...................................................... 7 关于本使用说明书...........................................
控制旋钮和功能 上面板 8 ! @ 7 6 # 5 $ 4 9 2 ) % ^ & * 3 A-1 B-1 C0 D0 E0 F0 G0 A0 B0 C1 C2 1 1 键盘 6 INPUT GAIN旋钮 S90 XS为88键键盘, S70 XS为76键键盘。所有键盘均具有力度响 应功能 (初始力度和触后力度)。初始力度,就是乐器可以感应您 使用该旋钮调节MIC INPUT插孔处音频信号的输入增益。视所连 接麦克风而定,您可能需要调节此旋钮以获得最佳音量。旋钮旋转 弹奏琴键的力量是强还是弱,并依据所选的音色使用该弹奏力度 到右侧时音量增大,旋转到左侧时音量减小。 以各种方式影响声音。触后力度,就是乐器可以感应在弹奏时您施 加到琴键上的压力大小,并依据所选的音色用该压力以各种方式 7 PEAK 指示灯 影响声音。 输入信号电平下降到削波以下3dB时该指示灯亮起。调整INPUT 注 S90 XS的键盘区为A -1到C7;S70 XS的键盘区为E0到G6。 GAIN,使指示灯在达到信号峰值时很少亮起。 2 弯音轮 8 Performance Control按钮
控制旋钮和功能 ¤ ( B H ¥ | J I Ú KL M Û O D N E A F Ü Ý C G C3 C4 ß P C5 C6 C7 [PART ON/OFF] 1 – 4 按钮 9 滑杆功能按钮 这些按钮可打开和关闭声部。在音色模式中,只可以使用声 按此按钮可改变分配到四个滑杆的功能。当前所使用参数旁边的 部1并且始终是打开的。 指示灯将亮起。 在音色编辑模式中,按此按钮几次将关闭所有指示灯,表示滑杆 [ARP ON/OFF] 按钮 打开/关闭“Arp Switch”(一种公共参数)。该按钮打开时,可 使用琶音功能。 可以用来控制当前编辑音色的音素电平。 ) 滑杆 [PART ARP] 1 – 4 按钮 可通过控制滑杆功能按钮控制所选参数。 可在演奏组音色/复合音色模式下,打开或关闭各声部的琶音 在音色模式中,可以使用最左面的滑杆。 在演奏组音色模式和复合音色模式中,这些滑杆可控制相应声部 播放。 在音色模式下,按[ARP ON/OFF]和[PART ARP] 1 按钮任何一 个将打开或关闭声部1的琶音播放,因为只有声部1可用
控制旋钮和功能 * TRANSPOSE [-]/[+] 按钮 @ ! 使用这些按钮将音符音高增大或降低一个半音。要恢复原八度设 定,同时按两个八度按钮。 ( LCD (液晶显示屏) 背光LCD显示屏用来显示当前的操作或模式的相关数值和参数。 # $ B % ^ & ! 旋钮功能按钮 C A 按这些按钮可改变分配到四个旋钮的功能。当前所使用参数旁边 的指示灯将亮起。在音色模式中,各旋钮的功能应用到当前音 G F 色,而在演奏组音色/复合音色模式中,各旋钮的功能只应用到当 A [SHIFT] 按钮 前所选的声部 (或应用到所有声部,视设定而定)。 与其它按钮一起按该按钮可执行各种命令。主要功能如下。 注 控制“EFFECT”功能的旋钮会始终影响到所有声部的声音。控制“MIC” 功能的旋钮将单独起作用。 @ 旋钮 钮功能按钮来改变旋钮的参数设定。 功能 [SHIFT] + START/STOP CLICK ON/OFF AUDIO REC/PLAY 移动到Audio Rec/Play模式中的Rec Standby 画面 VOICE 批量转储编辑过的音色 这四
控制旋钮和功能 E 光标按钮 K L 光标按钮用于在LCD显示屏中移动“光标”、高亮显示以及选择各 J 种参数。 O F [EXIT]按钮 M S90 XS/S70 XS的菜单和显示屏内容采用分级结构显示。按这个按 钮可以从当前显示级别退回到前一显示级别。也可以用来取消一 N 个“Job”或存储操作。 G [ENTER]按钮 P 使用该按钮调出所选菜单的画面。使用此按钮也可执行作业或存 储操作。 J BANK [DEC]/[INC] 按钮 每个按钮可以选择一个音色或演奏组音色库。 H I K [CATEGORY SEARCH] 按钮 当在音色/复合音色/演奏组音色声部编辑模式中打开这个按钮时, 可以使用[A]-[H]按钮选择音色的主类。当在演奏组模式中打开这 个按钮时,可以使用[A]-[H]按钮选择演奏的主类。 L [FAVORITE] 按钮 使用此便捷功能可以将所有您喜爱的常用音色存储在便于查找的 单独位置,并且按[FAVORITE]按钮即可将其调出。同时按住 [SHIFT]按钮和该按钮,可将当前程序添加到收藏夹分类。这种方 式非常有用,可帮您从乐器的大量音色中选择所需
控制旋钮和功能 P 数字[1] – [16]按钮 N 这些按钮的使用依[PART]、 [MUTE]和[SOLO]按钮的开关状态不同而 变化。如果每个按钮打开,则指示灯会点亮。 P 模式 音色演奏 [PART] 键盘发送通道设置 — 常规音色编辑 14 [MUTE] [SOLO] — — 音素选择 ([1] – [8]) 音素静音设定 ([9] – [16]) 音素选择 ([1] – [8]或[9] – [16]) 演奏组音色播放 键盘发送通道设置 声部静音设定 ([1] – [4]) 独奏声部选择 ([1] – [4]) 演奏组音色编辑 声部选择 ([1] – [4]) 声部静音设定 ([1] – [4]) 独奏声部选择 ([1] – [4]) 复合音色播放 声部选择 ([1] – [16]) 声部静音设定 ([1] – [16]) 独奏声部选择 ([1] – [16]) 复合音色编辑 声部选择 ([1] – [16]) 声部静音设定 ([1] – [16]) 独奏声部选择 ([1] – [16]) 主控播放 键盘传送通道设置 (当将单音色模式或演
控制旋钮和功能 后面板 3 1 2 1 (POWER 开关) 4 5 8 9 6 ) 7 ! 8 ASSIGNABLE OUT L和R插孔 按此按钮可将电源旋转到ON (打开图标)或OFF (关闭图标) 这两个输出与主输出 (通过下面的L/MONO 和R插孔)相对独 状态。 立,可自由分配到任何鼓组音色键或声部。这样,可对特定音色 或声音进行输出,然后用您喜爱的外部效果设备进行处理。 可分配到这些插孔的声部如下: 2 AC IN/输入插座 连接到附带的电源线。 • 分配了鼓/打击乐的鼓组音色按键 只可使用S90 XS/S70 XS附带的AC电源线。 • 演奏组音色的各个声部* • 复合音色的各个声部* 3 MIDI IN、 OUT和THRU端口 • 节拍器 MIDI IN用来接收其他MIDI设备 (如外部音序器)的控制信号或 演奏数据。使用该接口可通过外接MIDI设备控制合成器。 MIDI OUT用于将所有S90 XS/S70 XS的控制、演奏和播放数据传送至 其它MIDI设备 (如外接音序器)。 反过来,您可以使用S90 XS/S70 XS控制外部MIDI乐
连接安装 连接安装 电源 连接扬声器或耳机 将附带的AC电源线按照下列顺序连接。确保S90 XS/S70 XS 上的POWER开关设为关闭。 由于S90 XS/S70 XS不带内置扬声器,您需要使用外接设 备监听本设备的音色。请根据需要如下图所示连接一对耳 机、有源扬声器或其它播放设备。进行连接时,务必保证 电缆有适当的额定值。 1 将附带的电源线连接至乐器后面板上的AC IN/输 入接口。 有源扬声器 (左) 2 有源扬声器 (右) 连接电源线另外一端到电源插座。 耳机 POWER 开关 OUTPUT L/MONO OUTPUT R AC IN/输入 PHONES 注 断开电源线连接时,按照与此相反的步骤进行。 S90 XS/S70 XS 小心 请确保S90 XS/S70 XS的电压与您所在国家或地区使用的电压一致。电源 线包括接地针脚,以防止触电和对设备的损坏。连接到插座时,将适配器 的接地导线连接到接地螺丝。如果不知道如何连接,再与Yamaha经销商或 维修中心联系 (第63页)。 警告 只可使用S90 XS/S70 XS附带的AC电源线。如果更换了不符合规定的电源 线,
连接安装 调整音量和屏幕的亮度 选择音色 调节S90 XS/S70 XS以及相连的功放机/扬声器系统的音量。 在默认设定中,主控模式带有总共128个程序,每个程序 含有模式 (音色、演奏组音色、乐曲和复合音色)及其程 序编号。 尝试使用不同的主控程序弹奏各种音色和演奏组音色。使 用[INC]按钮、 [DEC]按钮或数据轮可改变主控程序编号。 注 连接到一套有源扬声器或PA设备时,将MASTER VOLUME设为大约 70%,然后将有源扬声器或PA设备的音量增大到适当的水平。 如果看不见显示屏内容,请使用后面板上的LCD CONTRAST旋钮调节到最佳可见度。 使用LCD CONTRAST旋钮调 整屏幕对比度。 用MASTER VOLUME 滑杆调整音量。 减小号码数值 增加号码数值 最大 暗 亮 最小 增加号码数值 减小号码数值 S90 XS/S70 XS 播放示范乐曲 S90 XS/S70 XS可提供各种示范乐曲,展示其富于动感的声音 和高级功能。以下将说明如何播放这些乐曲。 小心 请勿长时间以高音量使用耳机。否则可能会造成听力损伤。 注 确保S90 XS/S70 XS可
连接安装 将用户内存初始化为出厂 设置 S90 XS/S70 XS有出厂设置功能,此功能可以使S90 XS/ S70 XS的内存恢复到出厂默认设定。 这样可让您恢复S90 XS/S70 XS的默认程序,以及系统和 其它设置。 小心 当恢复出厂设置时,在各模式中创建的或者保存到内置闪存的所有数据都 将被删除。小心不要丢失重要数据。执行本操作之前请务必将所有重要数 据都保存到计算机中 (第47页)。 1 按[UTILITY]按钮。 将出现Utility Select画面。 2 使用光标[U]/[D]/[L]/[R]按钮选择“Fctry Set”, 然后按[ENTER]按钮。 出现Factory Set画面。 小心 将自动出厂设置参数设为打开并按[ENTER]按钮时,每次打开电源时将自 动执行出厂设置。 请注意,每次打开电源时,闪存ROM中的原始数据将被删除。因此,通常 自动出厂设置参数应设为关闭。将自动出厂设置参数设为关闭并按 [ENTER]按钮时,下一次打开电源时将不会执行出厂设置操作。 请注意,通过执行出厂设置,此画面上的电源打开自动出厂设置将被自动 保存。 3 按下[ENTER]按钮执行出厂
入门指南 模式 在S90 XS/S70 XS中带有多种操作模式,可以使用7个模式按钮进行选择。这些模式包括:音色、演奏组音色、复合音色、 主控和音序播放。根据所选模式,您可以在键盘上演奏并创建自己的原创音乐。 如果想要正常演奏键盘,请使用音色或演奏组模式。如果您要创作音乐,特别是多声部乐曲时,可使用复合音色模式。 另外,还有下列模式:可将键盘演奏录制为音频数据并播放音频文件的Audio Record/Play模式,可将在本合成器上所创建 数据保存对文件进行管理的文件模式,以及进行整体设置的实用模式。 从键盘演奏音色 从键盘演奏复合音色 创建原创程序组 音色模式 演奏组模式 主控模式 [VOICE] 按钮 [PERFORM]按钮 [MASTER]按钮 这种合成器有大量高品质、逼真的声音-就 是指“音色”。您可在键盘上的音色中选择播 放音色,一次只能播放一种音色。这种模式 还能帮您创作您自己的原创音色。 这种模式可让您演奏并创建演奏组。演奏组 模式可让您可以在键盘分层模式下将多种音 色合并在一起,或者在键盘分区模式下演奏 不同的2种音色。 这种特殊模式可让您注册并使用在各个音 色、演奏组音
基础知识介绍 音色是S90 XS/S70 XS的基本组成单位 音色模式中创建的音色是本乐器中其它模式的基本组成单位。演奏组音色和复合音色程序由不同的音色组成。 本乐器包含多种预置音色,用以演奏多种音乐风格。请尝试通过搜索音色找到您喜欢的音色。找到喜欢的音色后,您可试着在其 中加入自己的创意并使用编辑功能创作出您自己的原创音色。 选择预置音色 第21页 改变音色的音质 第23页 组合多种音色创建演奏组音色或复合音色 如果想要同时弹奏多种不同音色,请选择演奏组音色。一共有384种演奏组音色预编程并可如此使用,但也可以更改并自定义以适 合您自己的需要。使用Performance Creator功能,您就可以根据在音色模式中当前所选音色创建您自己的原创演奏组。 若要将本乐器作为计算机DAW软件中的复合音色音源使用,请选择复合音色。借助复合音色,本乐器可播放相连USB设备或内置 闪存设备上的MIDI乐曲文件。 使用您喜爱的音色在音色模式中创建一段新的 演奏组 (Performance Creator) 第28页 选择一种演奏组音色 第32页 使用复合音色和计算机创建音乐 第38页 随MIDI文件
在音色模式中弹奏键盘 在Voice Play画面中 (音色模式的顶部画面),您可以选 择并演奏一种音色。 本乐器的音色分为以下两种类型: 常规音色 常规音色主要是可以在键盘区域内演奏的、有音高的乐器 型声音 (钢琴、风琴、吉他等)。 选择预置音色 1 按[VOICE]按钮。 这会调出Voice Play画面。([VOICE]按钮指示灯亮起。) 2 使用BANK [DEC]/[INC]按钮选择一个音色库。 鼓组音色 在这种情况下,演奏键盘让显示在显示屏中的音色发声。 鼓组音色主要是分配给各音符的打击乐/鼓声。这些音色用 于演奏节奏部分。 在音色演奏模式中显示的参数简要解释如下。 音色演奏画面 本乐器具有记录音色的音色库。音色库基本上有三种类 型:预置、用户和GM。包含的音色和功能取决于如下所 述的音色库。 主类 音色库 程序编号 子类 预置音色库 预置音色库包含全套经过专门编程的音色。您自己编辑的 音色不能保存在预置音色库中。 用户音色库 音色名 用户音色库包含您自己编辑和存储的音色。默认是预置音 色中挑选的。 琶音速度 表示相应效果的状态。 (效果关闭时不显示。)
在音色模式中弹奏键盘 使用分类查找功能 无论音色库处于什么位置,音色正常被分为特定的分类。 分类根据常规乐器类型或声音特点来划分。分类查找功能 可让您快速访问需要的声音。 1 按Voice Play画面中的[CATEGORY SEARCH] 按钮。 将您最常用的音色分组—收 藏夹分类 分类功能还带有方便的收藏夹分类,可将您最常用和最喜 爱的音色放在一起以方便选择。这种方式非常有用,可帮 您从乐器的大量音色中选择所需的音色。 出现分类查找对话。 主类 将您喜爱的音色登录到收藏夹分类中 1 2 子类 2 3 用光标[U]按钮将光标位置移动到“Main” (主 类),然后用数据轮选择主类。 执行“使用分类查找功能”的步骤1到4,调出所选 分类的音色一览表。 按光标[R]按钮将光标位置移动到收藏夹复选框 栏。 3 用光标[U]/[D]按钮或数据轮选择所需的音色。 4 按[ENTER]按钮勾选收藏夹复选框。 在复选框中插入勾选标记,所选音色将被注册到收藏夹分类。 若要取消复选框中的勾选标记,请再按一下[ENTER]按钮。 用光标[D]按钮将光标位置移动到“Sub” (子 类),然后用数据轮
在音色模式中弹奏键盘 选择收藏夹分类中的音色 改变音色的音质 1 将显示注册到收藏夹分类中的音色一览表。 旋钮1 -4可调节当前音色的各种参数,如效果深度、起音/ 释音特性、音质和其它。每个旋钮上可分配5种功能,使 用旋钮功能按钮可交替选择。 2 用光标[U]/[D]按钮或数据轮选择音色。 1 3 按[ENTER]按钮确定调出音色。 按Voice Play画面中的[FAVORITE]按钮。 按旋钮功能按钮 (位于旋钮1 – 4左侧),如有必 要请重复按下按钮,这样对应所需功能的指示灯 便会亮起。 此时将出现Knob Select弹出画面。在弹出画面中,将显示当 前指定到旋钮的功能以及功能的当前值。 若要关闭弹出画面,请按[EXIT]按钮。 调出Simple画面 从Voice Play画面中,按住[SHIFT]按钮再按光标[L]/[R] 按钮可以调出Simple画面。 Simple画面可显示比正常字符 尺寸大的音色名称。可以选择三种字符类型。 旋钮功能按钮 指定到旋钮1–4的功能 功能的当前值 Simple画面1 未编辑数值 (之前已保存) 注 当在Utility Gener
在音色模式中弹奏键盘 调节音素电平 编辑 (E)指示器 当在Voice/Performance/Multi Play或Edit画面中改变了参数 值时,编辑指示器将会出现在LCD显示屏的右上角。这样就 可以快速确认出当前已被修改但尚未存储的当前音色/演奏 组音色/复合音色。若要存储当前编辑过的状态,请遵照指 示操作。 1 按音色模式中的[EDIT]按钮。 2 按滑杆功能按钮几次,使指示灯熄灭。 3 使用数字[1]–[8]按钮选择要编辑的音素。 4 使用滑杆设置选定音素的输出电平。 选择任意一个数字[1] – [4]按钮时,音素1 – 4的电平将被指定 音色编辑 到滑杆1 – 4。选择任意一个数字[5] – [8]按钮时,音素5 – 8的 电平将被指定。 “编辑”指的是通过改变组成音色的参数来创建音色的过 程。编辑可在音色模式的音色编辑子模式中进行。选择的 音色类型不同,可供编辑的参数也不同。 使用效果增强声音 常规音色编辑 一种常规音色 (有音高的乐器型声音)由最多8个音素组 成。有两种单音色编辑画面: Common Edit (编辑所有8 个音素通用的设置)和Element Edit
在音色模式中弹奏键盘 4 将光标移动到“Effect”,然后按[ENTER]按钮。 8 用数据轮将光标移动到“Preset”,然后选择预设。 预设包括当前所选效果类型的参数典型设置。尝试多个预设, Voice Edit Effect画面出现。 这样您就可以发现每个效果是如何影响声音的。 注 当琶音/效果功能设为“EFFECT ON/OFF”时,也可以同时按住 [SHIFT]按钮和[INS]按钮来调出Voice Edit Effect画面。 5 9 如果需要,设置每个参数。 精确编辑每个效果类型的参数可缩小您所需要声音的范围。 移动光标到“Ins A”,然后按[ENTER]按钮。 这时将显示当前效果的参数。 10 6 7 用数据轮将光标移动到“Category”,然后选择 分类。 如果编辑了预置音色,您的编辑会被作为用户音色保存。 11 用数据轮将光标移动到“Type”,然后选择效果 类型。 设置所有参数后,按[STORE]按钮将您的设置 保存为用户音色。 使用数据轮选择目标存储器,按[ENTER]按钮 调出确认信息,然后重新按[ENTER]按钮。 注 如果想要编辑插入B效
在音色模式中弹奏键盘 使用琶音功能 打开/关闭琶音 琶音功能可以根据您所演奏的音符自动触发预置的琶音乐 句、乐段和节奏模式。 该功能不仅可以为您的演奏提供灵感和节奏篇章,为您在 创作乐曲时保证所使用MIDI数据的质量,还可以为您的现 场表演使用的完整的伴奏部分。您可以将所需的5种琶音 类型分配给每种音色。也可以将需要的5种琶音类型指定 到每个演奏组音色/复合音色的各个声部,并且最多可以同 时播放4个声部的琶音。 您还可以设置琶音播放方式、力度范围和演奏效果来创建 您自己的原创唱片。此外,还可以通过MIDI输出发送琶音 播放,使您能将琶音数据录制在音序器上。 若要打开或关闭琶音播放,按面板上的 [ARP ON/OFF]按钮。 以MIDI数据形式发送琶音类型 选择琶音类型 琶音乐段可通过将如下参数设为打开以MIDI数据发送: ■ 音色琶音 音色模式 Æ [UTILITY] Æ 在Utility Select画面中选择 “Voice”Æ [ENTER] Æ 在Utility Voice Select画面中选择 “Arpeggio”Æ [ENTER] Æ“Arp MIDI Out Sw” ■ 演奏组
在音色模式中弹奏键盘 6 找到您喜爱的样式后,按[STORE]按钮将设置保 存为用户音色。 将琶音类型复制到另一个琶音声部 遵照说明将指定到琶音1的琶音类型复制到琶音2 – 5。 1 按琶音/效果功能按钮选择“ARP SELECT”。 2 按功能[1]按钮。 3 按住[STORE]按钮的同时,按功能[2] – [5]按钮 之一。 改变琶音类型 若要更改5种类型中的琶音,请使用琶音/效果功能按钮和 功能按钮。 琶音/效果功能按钮 功能按钮 1 按面板上的[ARP ON/OFF]按钮打开琶音功能。 2 按琶音/效果功能按钮选择“ARP SELECT”。 3 使用功能按钮更改琶音类型。 S90 XS/S70 XS 使用说明书 27
使用您喜爱的音色制作新的演奏 (Performance Creator) 本乐器具有便捷的Performance Creator功能,可让您使用在音色模式中您所找到的喜爱的音 色制作新的演奏。该功能可让您将与音色相关的参数设置 (如效果)复制到演奏组音色—这 样您就可以快速、轻松、精确地获得您想要的声音。 Performance Creator具有三种方便的功 能:分层、分区和鼓组指定。 分层—一起演奏不同的音色 4 将出现Performance Play画面。 本部分介绍了如何将键盘上不同的音色穿插在一起来制作 演奏。例如,制作出这样的演奏后,您就可以演奏出钢琴 和弦乐声穿插在一起,层次分明、浑厚的声音。 1 在音色模式中选择一种音色。 5 2 从列表中选择所需要的音色,然后按[ENTER] 按钮。 按[STORE]按钮将设置保存为演奏组音色。 按面板上[LAYER]按钮。 出现Category Search画面。 注 当按下Store画面中的[EDIT]按钮时,您可以在保存目的地检查音 色/演奏组音色/复合音色的声音。 3 选择包含想要分层音色的类别,然后按光标[R] 按钮。 将
s90xs_sc_om.
使用您喜爱的音色制作新的演奏 (Performance Creator) 鼓组指定—将鼓组声部分层 到当前音色 本节介绍了如何创建除了当前音色之外还可以触发鼓组样 式的演奏组音色 (通过琶音功能)。 1 在音色模式中选择一种音色。 2 按前面板中的[DRUM ASSIGN]按钮。 更改鼓组模板 (琶音类型) 执行鼓组指定功能会将鼓组音色指定到声部4,并将声部4 的琶音设为打开。如果想要更改鼓组模板,请在演奏组声 部编辑中选择不同的琶音类型。 5 按Performance Play画面中的[EDIT]按钮。 Performance Edit Select画面出现。 6 使用光标按钮选择声部4,然后按[ENTER]按钮。 将出现Drum Assign画面。 Dr/Pc (鼓/打击乐)自动指定到分 类。鼓组音色指定到声部4,然后琶音自动打开。演奏键盘触 发琶音。 3 按光标[R]按钮。 将显示音色一览表。 7 4 使用光标按钮选择“Arpeggio”,然后按[ENTER] 按钮。 从列表中选择所需要的鼓组音色,然后按 [ENTER]按钮。 将出现Performance Play画面。
使用您喜爱的音色制作新的演奏 (Performance Creator) 9 使用数据轮更改主类/子类/类型来查找您喜爱的 样式。 5 使用数据轮和光标按钮选择所需的字符,然后按 [INC]按钮输入选择的字符。要取消所选字符,按 [DEC]按钮。 最多可以输入20个数字字母字符。 6 输入字符后,按[ENTER]按钮。 7 按[STORE]按钮。 这时会显示用户音色库和程序。 您可通过相同的操作改变琶音2-5的样式。若要在5种琶音 之间更改,请使用功能按钮。按琶音/效果功能按钮将 “ARP SELECT”打开,然后按功能按钮。 琶音/效果功能按钮 8 选择所需的音色库和程序,然后按[ENTER]按 钮。 功能按钮 为演奏组音色指定名称 您可以为音色和演奏组音色指定名称,然后将设置保存为 用户音色/演奏组音色。 9 出现确认对话后,按[ENTER]按钮。 注 当按下Store画面中的[EDIT]按钮时,您可以在保存目的地检查音 色/演奏组音色/复合音色的声音。 1 按Performance Play画面中的[EDIT]按钮。 Performance Edit Select画面出
在演奏组音色模式中弹奏键盘 选择演奏组音色 选择演奏组音色与选择音色的方式基本相同。在演奏组播放模式中也可使用分类查找功能。请注意, S90 XS/S70 XS不带 预设演奏组,只有3个用户音色库。 按此按钮编辑整个演奏 组音色 按此按钮选择声部 改变音色的音质 与在音色模式中一样,演奏组的声音 (最多包括4种声部或音色)可通过演奏组模式中的旋钮或滑杆进行编辑。编辑演奏 组音色有两种方式:编辑整个演奏组音色,以及只编辑指定到演奏组音色的特定声部 (音色)。要编辑的声部是通过演奏 组控制按钮来选择。若要编辑整个演奏组,按[COMMON]按钮然后旋转旋钮。若要编辑当前演奏组的特定音色,使用 [PART SELECT]按钮,然后旋转旋钮选择所需的声部。 注 按住[SHIFT]按钮并按[COMMON]/[PART SELECT]按钮,调出Common Edit Select画面/Part Edit Select画面。此功能适用于编辑演奏组。 最左侧的4个滑杆可调节4声部中各声部的音量、声相、叠奏发送和混响发送。通过滑杆功能按钮选择功能,然后移动滑杆。 通过滑杆功能按钮选择功能。 32 S90 XS/S70
用连接的麦克风演唱 把麦克风连接到乐器后面板上的MIC INPUT插孔 (组合插孔),您便可以伴随自己的演奏歌唱。也可以使用MIC INPUT插 孔将内置效果应用到该信号输入,其中包括明显的声码器效果。下面的示例假设您想要演奏键盘时歌唱。 1 将麦克风插入后面板上的MIC INPUT插孔。 2 按面板上的[MIC ON/OFF]按钮使指示灯亮起。 3 使用INPUT GAIN旋钮调整麦克风输入电平。 调整输入增益,使PEAK指示灯快速闪烁。 4 按旋钮功能按钮选择“MIC”,再使用指定VOLUME的旋钮调整音量。 5 根据需要,控制指定PAN、 CHORUS SEND和REVERB SEND的旋钮。 S90 XS/S70 XS 使用说明书 33
使用USB存储设备录制/播放 (录音/播放模式) 录音/播放模式可以将键盘演奏录制成音频数据。录制的音频数据将以音频文件保存到外部USB存储设备或内置闪存的根目 录,可让您从指定的存储设备播放音频文件。 录音 4 在本节中,您将了解到如何将键盘演奏录制为立体声波形 文件 (44.
使用USB存储设备录制/播放 (录音/播放模式) 8 出现“Save Audio Rec File?”信息时按[ENTER] 按钮。 播放录音 您的演奏会音频文件保存到USB存储设备的根目录。 请注意,您已经录制好了键盘演奏的音频,请尝试播放文 件。 完成保存操作将调出Audio Play画面。 1 从Audio Play画面中,用光标[U]/[D ]按钮移动 光标来选择所需文件。 录制的音频文件将按数字顺序命名 (“000.wav”、 “001.
使用连接的计算机 将本乐器连接到计算机后,就可以充分利用下列功能和应用程序。 • DAW软件和MIDI键盘的外部音源 • DAW软件的遥控器 • 从计算机进行更详细的音色编辑(S90 XS/S70 XS编辑器) 3 连接到计算机 请务必启用本乐器的USB TO HOST端口。 按[UTILITY]按钮调出实用模式,通过光标按钮选择“MIDI”, 然后按[ENTER]按钮调出MIDI画面。将MIDI In/Out参数设为 将S90 XS/S70 XS连接到计算机需要USB电缆和USB-MIDI 驱动程序。请按照下列说明进行操作。请注意,可用USB 电缆传输MIDI数据。 “USB”。 注 由于S90 XS/S70 XS没有内置扬声器,因此需要外接音频系统或立体声 耳机才可以正常试听。有关详细信息,请参见第16页上的“连接安装”。 1 可从本公司的以下网站下载USB-MIDI驱动程序。 单击下载按钮后,请解压压缩文件。 http://www.global.yamaha.
使用连接的计算机 使用USB TO HOST端口时的注意事项 MIDI通道和MIDI端口 当通过USB TO HOST端口将S90 XS/S70 XS连接到计算机 时,您必须注意以下几点。 如果未能遵照执行,可能会导致乐器和/或计算机挂起 (死 机),并可能导致数据损坏或丢失。如果计算机或S90 XS/ S70 XS死机,请关闭,然后打开S90 XS/S70 XS的电源,再 重启计算机。 MIDI数据被分配给16个通道中的一个,此合成器能通过16 个MIDI通道同时演奏16个独立声部。不过, 16个通道限制 也可以通过单独的MIDI“端口”来解决,每个MIDI端口支持16 个通道。一根MIDI电缆的标准为可以最多同时使用16个通 道处理数据,而USB连接可以处理更多的数据并提供更多通 道-这就有赖于MIDI端口的使用。每个MIDI端口可以调用 16个通道, USB连接最多允许8个端口的使用,结果是:可 以在计算机上使用最多128个通道 (8个端口x 16个通道)。 当使用USB电缆将本乐器连接至计算机时, MIDI端口定义 如下: • 将计算机连接到USB TO HOST端口之前,请退出计算机 的任
使用连接的计算机 用作复合音色音源 (复合音 色模式) 以下说明为如何将本乐器用作MIDI音源的方法。此时,实 际MIDI音序数据从计算机上的DAW或音序器上发送,允许 您避免使用软件效果并节省计算机的处理电量。 设置S90 XS/S70 XS 1 按[MULTI/SEQ PLAY]按钮进入复合音色模式。 2 选择要被编辑的复合音色。 3 按[MIXING]按钮调出Mixing画面。 4 根据需要设置声部1-16的混音。 遥控软件 (远程模式) S90 XS/S70 XS具有方便的远程模式,可让您通过S90 XS/ S70 XS面板操作在计算机上控制DAW软件和软件合成器。 例如,您可以通过使用功能按钮在计算机上开始/停止DAW 软件的播放、并使用数据轮、 [INC]和[DEC]按钮控制DAW 软件上的乐曲位置,而无需使用计算机的鼠标或键盘。 S90 XS/S70 XS的远程控制模式可控制DAW应用程序 Cubase、 Logic Pro、 SONAR和Digital Performer。本乐 器内存中最多可以保存VST乐器的50种控制模板。使用 S90 XS/S70 XS远程编辑器来编
使用连接的计算机 遥控设置 SONAR 注 进行DAW Remote设置时,请务必正确安装USB-MIDI驱动程序和 1 S90 XS/S70 XS远程工具。 设置S90 XS/S70 XS 2 3 1 用USB电缆 (第36页)将本乐器连接到计算机。 2 按[DAW REMOTE]按钮进入远程模式。 3 按[UTILITY]按钮调出实用模式的Remote画面。 4 下拉[Options]菜单并选择[MIDI Devices]调出“MIDI Devices”窗口。 向输入设备添加“Yamaha S90 XS (S70 XS)-2”,然后 向输出设备添加“Yamaha S90 XS (S70 XS)-2”。 下拉[Options]菜单,并选择[Control Surfaces]调出控制 界面窗口。 单击[+]按钮,选择“Mackie Control”,然后将输入端口设 为“Yamaha S90 XS (S70 XS)-2”并将输出端口设为 “Yamaha S90 XS (S70 XS)-2”。 Digital Performer 1 2 4 将“DAW Select”设为所需
使用连接的计算机 编辑控制模板 编辑音色的详细参数 使用S90 XS/S70 XS远程编辑器来编辑控制模板。 关于S90 XS/S70 XS 编辑器 S90 XS/S70 XS 远程编辑器可以从下列URL下载: http://www.yamahasynth.
随MIDI文件播放演奏键盘 想随着MIDI文件播放演奏键盘时应使用复合音色模式/音序演奏模式。本乐器具有可用于播放的16轨音序器,最多可播放 16个轨道的MIDI数据。 执行下列指示前,请准备MIDI文件 (通过DAW软件或其它方法)然后保存到USB存储设备。您也应该创建适当的复合音 色进行播放。 1 2 3 将包含MIDI文件的USB存储设备连接到本乐器后 面板上的USB TO DEVICE端口。 5 按几下 [MULTI/SEQ PLAY] 按钮进入音序演奏 模式。 使用数据轮和 [DEC]/[INC] 按钮,选择播放顺序 001 ,然后选择用于播放 MIDI 文件的所需复合 音色。 6 4 选择USB存储设备路径(本例中为“usb1-1”),然 后按[ENTER]按钮。 7 使用光标按钮将光标移动到播放顺序002,然后 按[ENTER]按钮。 选择所需要的MIDI文件,然后按[ENTER]按钮。 显示用来选择音序播放编号的画面后,按 [ENTER]按钮。 出现File Load画面。 8 显示确认画面后再次按[ENTER]按钮。 S90 XS/S70 XS 使用说明书 41
随MIDI文件播放演奏键盘 9 按[EXIT]按钮几次,可以回到音序演奏模式。 可以通过相同的操作来完成音频文件选择。 10 11 12 使用光标按钮将光标移动到播放顺序003,然 后使用数据轮和[DEC]/[INC]按钮选择“end”。 按[1] –16]其中一个按钮选择键盘演奏组的声部。 使用光标按钮将光标移动到播放顺序001,然后 按[START/STOP]按钮开始播放。 记录到顺序 001 的复合音色设置将被调出,然后启动 MIDI 文件。 13 42 演奏键盘。 S90 XS/S70 XS 使用说明书
作为主控键盘使用 (主控模式) 主控模式可帮助您: • 创建并保存最多128个程序,每个程序包含一个音色、一个演奏组音色或一个复合音色,并且每个组件都可以立即调出来 使用。 • 在每个主控程序中最多可以指定到的四个单独区域,用作主控键盘。 您可以使用主控模式来记住经常使用的设置,其中包括所使用的模式,并且只需按一下按钮即可在需要的时候调出这些设 置。另外,还可以记住主控程序控制的外部MIDI设备的设置,可让您在现场表演时按顺序更改和控制连接的外部MIDI音源。 保存编辑过的音色/演奏组音 色/复合音色 5 使用光标按钮选择“Memory”,然后按[ENTER] 按钮。 Common Memory画面出现。 如果想要快速调出特定音色然后调出相关的特定演奏组, 将音色模式指定到一个主控程序编号 (例如, 001)并将 演奏组模式指定到下一个编号的程序 (即, 002)将会是 一个很好的选择。遵照下列步骤保存程序。 1 按[MASTER]按钮进入主控模式。 2 选择要编辑的主控。 6 Master Play画面出现。 3 按[EDIT]按钮。 Master Edit Select画面出现。
作为主控键盘使用 (主控模式) 3 按[EDIT]按钮。 8 Master Edit Select画面出现。 使用光标按钮选择“Zone 1”,然后按[ENTER] 按钮。 Zone Edit Select画面出现。 4 选择“Common”,然后按[ENTER]按钮。 Common Edit画面出现。 5 9 在单独的Transmit、Note、Preset和Knb/Sldr画 面中进行区域1的设置。 Transmit 画面 选择“Zone Sw”,然后按[ENTER]按钮。 Common Zone Switch画面出现。 Note 画面 6 设置“Zone Switch”为“on”。 “Knob/Slider”参数会自动设为打开。 Preset 画面 注 将旋钮/滑杆用作旋钮功能/滑杆功能的控制器时,将旋钮/滑杆设 为关闭。 7 Knob/Slider 画面 按[EXIT]按钮两次返回Master Edit Select画面。 10 11 按[EXIT]按钮返回Master Edit Select 画面,然 后使用相同的操作设置其它区域。 设置所有需要的参数后,
进行全局系统设置 (实用模式) 在实用模式中可设置应用到本乐器整个系统的参数。若要进入实用模式,按[UTILITY]按钮。按[EXIT]按钮返回原先的画面。 本节介绍了实用模式中一些有用的功能。 设置打开电源时的默认模式 微调 常规Æ 打开电源模式 微调 在Voice、 Performance、 Multi和Master画面中,在此指定 的模式会在打开电源时调出。 单独调节键盘某个音符的音高。 翻转LCD状态 应用到从MIC INPUT插孔所输出信号的效果 设置 常规Æ LCD模式 音色Æ A/D FX 该参数决定LCD状态。 决定在音色模式下应用到从MIC INPUT插孔信号输入的音 效设置和声码器设置。 选择“normal”时: 注 有关如何应用插入效果的详细信息,请参见第24页。 音色模式中的主控效果/主EQ设置 选择“reverse”时: 音色Æ主FX、主EQ 决定多大程度的效果和EQ处理应用到主输出。 节拍器设置 常规Æ节拍器开关 – 输出选择 决定节拍器的速度、音量和输出目标。 S90 XS/S70 XS 使用说明书 45
进行全局系统设置 (实用模式) 更改面板锁定设置 面板锁定 决定按下面板上的[PANEL LOCK]按钮时,按钮为“锁定”还 是变为禁用状态。取消选择复选框时,即使打开了面板锁 定相应的按钮仍可用。 快速设置 快速设置 该功能可让您只需在预设中选择一种,即可调出在演奏组 模式/复合音色模式中有关外部连接的参数设置。由于只要 选择快速设置编号,即可将各种画面中的参数设为适当的 数值,因此该功能非常方便。每个快速设置编号的初始设 置和说明如下: 快速设置编号 46 说明 1 将除琶音数据之外的演奏组数据录制到计算机上的 DAW软件时。 2 将包括琶音数据的演奏组数据录制到计算机上的DAW 软件时。 3 在不连接DAW软件或其它MIDI设备的情况下,将S90 XS/S70 XS用作单独设备时。 S90 XS/S70 XS 使用说明书
保存/加载数据 (文件模式) 在文件模式中,您可以保存/加载在本乐器上创建的数据,如音色和演奏组音色。若要进入文件模式,按[FILE]按钮。 本节介绍了如何将本乐器用户存储器上的所有数据作为“All”文件保存/加载 (扩展名:X2A)。 将设置保存到USB存储设备 5 选择所需要目录,然后按[ENTER]按钮。 若要将文件保存到目录,将光标移动到“NEW FILE”,然后按 [ENTER]按钮。将显示选择文件类型的画面。 1 2 将USB存储设备连接到本乐器的USB TO DEVICE端口。 按[FILE]按钮进入文件模式。 将出现File Select画面。 6 选择文件类型,然后按[ENTER]按钮。 如果想要保存所有数据,请选择“All”。当将通过“All”保存的数 据载回到乐器,您仍然可以选择想要检索的特定数据—例如 特定的音色或特定的音色库,以及所有数据。 3 使用光标按钮选择 “Save” ,然后按 [ENTER] 按钮。 7 使用数据轮和光标按钮选择所需的字符,然后按[INC]按钮输 入选择的字符。要取消所选字符,按[DEC]按钮。 内置闪存和USB存储设备显示在File
保存/加载数据 (文件模式) 从USB存储设备加载设置 6 选择所需的数据类型,然后按[ENTER]按钮。 若要将所有音色或演奏组音色加载到所有内部用户音色库,选 择“Voice”或“Performance”,然后按[ENTER]按钮。若要加载 1 2 按[FILE]按钮进入文件模式。 将出现File Select画面。 3 使用光标按钮选择“Load”,然后按[ENTER]按钮。 内置闪存和USB存储设备显示在File Load画面上。 4 使用光标[U]/[D]按钮选择USB存储设置,然后 按[ENTER]按钮。 将显示USB存储设备的根目录。 如果在USB存储设备上有文件夹或目录,使用光标[R]按钮移 动路径。 5 将“.
保存/加载数据 (文件模式) USB存储设备 连接示例 硬盘驱动器等USB存储设备 USB闪存 或 USB TO DEVICE 端口 S90 XS/S70 XS 兼容的USB设备 USB TO DEVICE接口上只可连接1个USB存储设备 (如硬 盘、 CD-ROM驱动器、闪存和其它驱动器)。不能连接使 用其它USB设备,如计算机键盘或鼠标。总线供电 (由主 机设备供电)和自供电 (依靠电池或外接电源适配器供 电)类型设备都可以使用。 在购买USB存储设备之前,请咨询Yamaha代理商或授权经 销商 (参见本说明书末尾的清单),也可访问下列网页: http://www.yamahasynth.
附录 屏幕显示信息 LCD 指示 50 说明 All data is initialized upon power-on. Continue? 确认是否想要打开“Power on auto factory set switch”参数。 Are you sure? 确认是否要执行特定操作。 Assign Vocoder Voice to Part 1. Continue? 当声部1不是演奏组/复合音色模式中的声码器音色时,如果将A/D输入声部的输出选择设为“Vocoder”, 确认是否想要通过Category Search画面选择声码器音色。 Assign Vocoder Voice. Continue? 当音色不是音色模式中的声码器音色时,如果将A/D输入声部的输出选择设为“Vocoder”,确认是否想要 通过Category Search画面选择声码器音色。 Audio Rec stopped due to lack of memory space. 当存储器空间不足而造成录音停止时,该信息出现。 Bad disk or memory.
屏幕显示信息 LCD 指示 说明 Load All. Are you sure? 确认是否想要将“All”加载到文件模式。 Load Seq Chain file. Are you sure? 确认是否要将“Seq Chain file”加载到文件模式。 MIDI buffer full. 因为即时接收的数据过多导致不能处理MIDI数据。 MIDI checksum error. 当接收批量数据时发生错误。 Mixing Voice full. 混音音色不能保存,因为已经保存的音色数量已经超过了最大容量。 No read/write authority to the file. 没有在外部存储设备上读取/写入的权限。 Now executing Factory set... Please keep power on. 表示本合成器正在恢复出厂预设设定。 Now loading... 表示正在加载文件。 Now receiving MIDI bulk data... 表示本合成器正在接收MIDI批量转储数据。 Now saving...
故障排除 下表提供了一些常见问题的故障排除提示和参考页。在将数据备份至外接存储设备后,通过执行出厂设置 (第18页)有可 能解决问题。如果问题仍没有解决,再与Yamaha经销商或维修中心联系 (第63页)。 没有声音 是否已将S90 XS/S70 XS通过音频电缆正确连接至相关的外接装置 (例如,放大器、扬声器、耳机)? 由于S90 XS/S70 XS没有内置扬声器,因此需要外接音频系统或立体声耳机才可以正常试听。 本合成器和连接至本合成器的外接装置的电源是否打开? 是否已进行了所有适当电平的设定—包括本合成器上的主控音量和任何相连外接装置上的音量设定? 踏板控制器是否踩下去了 (当其连接到FOOT CONTROLLER插孔时)? 是否已将全部四个滑杆设定为适当的电平 (零或最小值除外的值)? 本地控制是否设为OFF? 如果设置为关闭状态,内部音源不发声。 [UTILITY] Æ MIDI Æ 本地控制 使用外接控制器时, MIDI音量或MIDI表达设定是否过低? 效果器与滤波器设置是否正确? 如果使用滤波器,试着改变截止频率。某些截止设定有可能会过滤掉所有声音。 [VOI
故障排除 音素开关、声部开关、音符范围和力度限制等参数设定是否恰当? [VOICE] Æ [EDIT] Æ [MUTE] (亮起) Æ 数字[9] – [16] 按钮 [PERFORM] Æ [PART ON/OFF] [PERFORM] Æ [EDIT] Æ 声部选择 Æ 演奏模式 Æ 音符范围低/高 [PERFORM] Æ [EDIT] Æ 声部选择 Æ 演奏模式 Æ 力度限制低/高 当演奏组音色/复合音色没有声音时,是否向各声部分配了音色? [PERFORM] Æ [EDIT] Æ 声部选择 Æ 音色 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 声部选择 Æ 音色 当演奏组音色/复合音色没有声音时,各声部的输出设置是否正确? [PERFORM] Æ [EDIT] Æ 声部选择 Æ 演奏模式 Æ 输出选择 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 声部选择 Æ 演奏模式 Æ 输出选择 当复合音色没有声音时,外接音序器各音轨的输出端口/通道以及复合音色各声部的接收通道的设置是否正确? [MULTI/SEQ PLAY
故障排除 不经停止继续播放 当[ARP ON/OF]按钮打开时,按下使其指示灯关闭。 在音序播放模式中,按[START/STOP]按钮。 继续发出节拍器声音时,按住[SHIFT]按钮并按[START/STOP]按钮停止声音。 声音失真 效果设置是否恰当? 在某些设定下使用效果有可能会产生失真。 [VOICE] Æ [EDIT] Æ 效果 [PERFORM] Æ [EDIT] Æ 公共 Æ 效果 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 公共 Æ 效果 在某些设定下使用主控效果有可能会产生失真。 [UTILITY] Æ 音色 Æ 主控FX [PERFORM] Æ [EDIT] Æ 公共 Æ 效果 Æ 主控 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 公共 Æ 效果 Æ 主控 滤波器设置是否恰当? 过高的滤波器谐振设置可导致失真。 [VOICE] Æ [EDIT] Æ 滤波器/EG [PERFORM] Æ [EDIT] Æ 公共 Æ 滤波器/EG [PERFORM] Æ [EDIT] Æ 声部选择 Æ 滤波器/EG [
故障排除 不正确或意外的音高 实用模式中的调音参数是否设为“0”以外的其它值? [UTILITY] Æ 常规 Æ 调音 实用模式中的音符切换参数是否设为“0”以外的其它值? [UTILITY] Æ 常规 Æ 音符切换 当音色产生错误的音高时,是否从音色编辑模式的微调参数中选择了恰当的调音系统? [UTILITY] Æ 微调 当演奏组音色/复合音色产生错误的音高时,各声部的音符切换参数是否设为“0”之外的其它值? [PERFORM] Æ [EDIT] Æ 声部选择 Æ 演奏模式 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 声部选择 Æ 演奏模式 不应用效果 是否将REVERB和CHORUS旋钮/滑杆完全旋到最小值? 是否已将某个或所有效果类型设为“thru”或“off”? 是否每个效果的EFFECT ON/OFF参数设为OFF? 当在演奏组模式/复合音色模式中出现这种情况时,请检查插入开关 (插入效果开关)参数的设置是否正确。 [PERFORM] Æ [EDIT] Æ 声部选择 Æ FX发送 Æ 插入效果开关 [MULTI/SEQ PL
故障排除 不能启动琶音 确认[ARP ON/OFF]按钮为打开还是关闭。 MIDI同步参数设为自动还是内置 (使用内置时钟)? [UTILITY] Æ MIDI Æ MIDI 同步 您是否选择了 (没有用户数据的)用户琶音? 若要使用用户琶音,则必须将在MOTIF XS中创建的用户琶音数据加载到S90 XS/S70 XS。 诸如音符限制与力度限制类的琶音相关参数有无设置适当? [VOICE] Æ [EDIT] Æ 琶音 Æ 琶音编辑 Æ 音符限制低/高 [VOICE] Æ [EDIT] Æ 琶音 Æ 琶音编辑 Æ 力度限制低/高 [PERFORM] Æ [EDIT] Æ 声部选择 Æ 琶音 Æ 琶音编辑 Æ 音符限制低/高 [PERFORM] Æ [EDIT] Æ 声部选择 Æ 琶音 Æ 琶音编辑 Æ 力度限制低/高 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 声部选择 Æ 琶音 Æ 琶音编辑 Æ 音符限制低/高 [MULTI/SEQ PLAY] (选择复合音色模式) Æ [EDIT] Æ 声部选择 Æ 琶音 Æ 琶音编辑 Æ 力度限制低/高 当在
故障排除 MIDI批量转储数据传送/接收不能正常工作 接收批量转储参数是否设为关闭? 将接收批量转储参数设为开启。 [UTILITY] Æ [MIDI] Æ 接收批量转储 如果数据是用S90 XS/S70 XS的批量转储功能保存的,您必须将设备编号设为与批量转储发送前的相同编号。 [UTILITY] Æ [MIDI] Æ 设备编号 当传送无法正常工作时,连接至S90 XS/S70 XS的MIDI乐器的设备编号是否设为与实用模式中的设备编号参数匹配? [UTILITY] Æ [MIDI] Æ 设备编号 无法将数据保存至外部USB存储设备 所使用的USB存储设备是否写保护? (写保护在保存数据时应设为关闭)。 正在使用的USB存储设备是否已正确格式化? [FILE] Æ 保存 Æ 选择USB存储设备 Æ [JOB] Æ FORMAT 无法播放音频文件 音频文件的格式是否正确? S90 XS/S70 XS只能以44.1 kHz/16位播放立体声WAVE (.wav)/AIFF (.
s90xs_sc_om.
索引 A L [ARP ON/OFF] .............................................................. 26 ARP SELECT................................................................. 27 [AUDIO REC/PLAY] ...................................................... 34 [LAYER] ........................................................................ 28 LCD CONTRAST........................................................... 17 LCD 模式....................................................................... 45 Logic Pro ...................
索引 U USB TO HOST 端口 ...................................................... 36 USB 存储设备 ............................................................... 49 USB-MIDI 驱动程序....................................................... 36 V [VOICE]......................................................................... 21 VST3 插件 ..................................................................... 40 W 微调............................................................................... 45 文件模式 ........................
注意 软件许可协议 使用本软件前,请仔细阅读本软件许可协议 (“协议”) 。您仅允许根据本协议的条款使用本软件。本协议为用户(个人或法律实体)与Yamaha公司 (“Yamaha”)之间的协议。 打开本包装的封装后表示您同意受本许可中条款的约束。如果您不同意这些条款,请不要安装、复制或以其它方式使用本软件。 本协议提供了有关本产品附带的STEINBERG MEDIA TECHNOLOGIES GMBH(“STEINBERG”)“DAW”软件的使用条件。由于安装“DAW”软件时显 示在您的计算机显示器上的最终用户软件许可协议 (EUSLA)已被本协议所取代,所以您应忽略该EUSLA。也就是说,在安装过程中,您无须经过 判断就应选择“同意”该EUSLA,以便进入下一页。 1. 使用许可及版权的授予 6.
S90 XS/S70 XS 使用说明书
s90xs_sc_om.book Page 63 Tuesday, September 8, 2009 1:22 PM For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A. Tel: 714-522-9011 CENTRAL & SOUTH AMERICA MEXICO Yamaha de México S.A. de C.V. Calz.
Yamaha Web Site (English only) http://www.yamahasynth.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2009 Yamaha Corporation 909MW0.