特别声明 产品安全注意 : 雅马哈电子产品带有如下图所示的图标或铭牌。本页 中有对这些图形的解释。阁下请遵守本页中各项警示和安全使用部 分。 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
重要安全说明 本文涉及到个人伤害、触电和火灾危险的可能性 警告 - 使用任何电器产品,必须注意基本防范。这些防范包括: 1. 阅读所有的安全使用说明书、安装说明书、特殊信息条款以及装 配说明书。 8. 该设备不得放置于潮湿的地方,不得靠近水或淋雨。潮湿地点例 如:游泳池、温泉、浴盆、水池附近或地下室。 9. 该设备只许配备厂商指定的附属品带轮机架、机架或支架等,如果 使用这些产品,请仔细查阅设备所有安全标记和产品附带的说明书。 2. 不要在超出用户维护说明书范围以外擅自维修该产品。所有超出 范围的维修工作必须提交给有资格维修的技术人员来完成。 3. 电源确认:在任何销售地区,雅马哈产品的电压都被人工特定,如 果阁下需要变更或者对在阁下使用的地区的电压存在怀疑,请直接联 系阁下的经销商得到电压的证实和用法说明 (如有可能)。铭牌上印 好了所要求的电源电压。关于铭牌的位置,请查阅本手册 《特别通告 部分》中。 4.
注意事项 使用前请仔细阅读 * 为了日后参考请妥善保管该用户说明书至安全的地方。 警告 以下列出有关防止由于来自触电、短路、火灾或其他危险而造成严重伤害甚至死亡的条例,防范条例不不仅仅局限于以 下几条: 电源 / 电源线 防水警告 • 该设备只许使用指定的电源电压,该设备的铭牌上已明确指明使用 电压。 • 不要让设备遭受雨淋,不要放置于潮湿环 境,不要把盛有液体 的容器放置在该设备上,以防液体溅入设备的开口处。 • 定期检查电源插头,除去插头上附着的污垢或堆积其上的尘埃。 • 禁止用湿手去插拔电源插头。 • 只能使用该设备专用电源线及插头。 • 不要让电源线靠近诸如加热器、散热器等热源。不要过分地弯曲或 损伤电源线,不要在电源线上放置较重物品,不要将电源线安放在 行人易踩,或伴倒的地方或东西易落下的地方。 不要擅自打开机壳 防火警告 • 不要把燃烧物 (比如蜡烛等)放置在设备上,燃烧物会掉落其上 并引起火灾。 假如阁下发现任何异常 • 该设备含有禁止用户自行维修部分。阁下不得尝试分解和更改内部 组成部分。 • 如果发现电源线或插头被磨损、设备瞬间无声、闻到异味、有烟雾 出现,请立即关掉
连线 保存数据 • 在和其他电子设备连接之前,请关掉所有设备的电源。在给这些设 备开关电源之前一定要把所有设备的音量旋钮拧至最小。同样,连 接好开电后,保证所有设备的旋钮设置在最小然后逐渐把音量提升 到期望的电平值。 保养 • 在清洁设备时,请使用质地柔软的干布擦拭。不许采用油漆稀释 剂、溶剂、清洁剂或含化学药品的擦拭布。 存储和备份阁下的数据 • 当阁下关掉设备电源时, DRAM 数据 (见第 27 页)将被丢失。将 数据存贮于 FLASH ROM (闪存)中 (用户存储器;见第 73 页)。 当设备发生故障或遇到错误操作,储存数据会被丢失。 将重要的数 据存储到储存卡 (SmartMedia) 中。 操作注意事项 当数据已经被存储到闪存 (Flash ROM)中,请不要尝试关 电源 (当 "Executing...
介绍 感谢阁下购买雅马哈 S90 音乐合成器。为了阁下获得有关 S90 最全面的信息以及强大的功能,我们建议您仔细阅读这本 用户手册,并妥善保管,以便将来使用。 附件 • 交流电源插头 • 用户手册 • CD-ROM 光盘 x 2 • 数据表 • 安装指导 关于 CD-ROM CD-ROM 中含有 S90 应用软件。音色编辑器可以通过直观的图形界面来编辑音色,文件处理器可以轻松自如地在储 存卡和计算机之间转换文件。阁下可以通过音序软件 (WINDOWS 专用)轻松地创建和编辑电脑中的原始歌曲。 关于详细资料,请阅读安装指导分册或者软件在线指南。 不许把在 CD 音乐播放器中播放该 CD - ROM 光盘。否则将会让阁下的听力和 CD 音乐播放机 / 扬声器受损。 主要功能 • 高品质的动感音色―总共超过 512 种音色,包括 49 组鼓组(见第25 页)。通过分类快速搜寻和调用所需功能 ( 见第38 页)。 • 演奏音色模式可以同时支持四种不同音色―层叠或分割。(见第 25 页) • 众多的效果处理,包括回响 (12 种),合唱 (25 种),两个独立扩展效果部分 (共 104 种),一个
关于用户手册 该用户手册包含以下章节。 ■ 基本章节 (第 12 页) 该章节提供了有关 S90 主要功能和特点的概述以及有关基本操作规范。 ■ 快速指导 (第 36 页) 该章节提供了如何使用基本功能的解释和说明。 ■ 参考 (第 98 页) 该章节提供了 S90 所有功能和参数的解释和说明。 ■ 附录 (第 114 页) 该章节提供了 S90 合成器有关 MIDI、可选配产品的安装说明、显示屏信息、故障处理和规格等内容。 ■ 安装指导手册 (单独分册) 该分册用于指导用户如何通过 CD-ROM 在计算机中安装软件。 ■ 数据表 (单独分册) 该分册提供了诸如音色库表、音频表、演奏音色表以及 MIDI 执行图表。 关于参考数字 在常规的参考页面以外,还包括特殊的参考数字 (例如参考号 15)。它能让阁下方便快捷地交互参考第 93 页参数 表中相应的参数。(有关更详细的信息,请查阅第 96 页。) ● 除了个人使用以外,禁止为了任何意图而复制商用音乐数据和数字音乐文件。 ● 本产品包含雅马哈拥有版权或者使用许可权的计算机程序等内容。具体包括所有计算机软件,文字, MIDI 文件,音频 数据和录音。对以上
使用索引 该索引分隔出几大章节,当阁下希望寻找一个主题或功能时可以方便快捷地寻找到期望的信息。 ■ 聆听 / 回放 • 欣赏样本歌曲............................................................................. 回放演示曲目 ( 第 19 页 ) • 演奏音色.............................................................................................. ( 第 36 页 ) • 在期望的乐器组中调用音色.............................................................. 使用音色类别功能 ( 第 38 页 ) • 从存储卡中演奏歌曲.................................................................................... ( 第 75 页 ) • 转换标准 MIDI 文件从版本 1 到版本 0........
• 根据力度改变音色因子 / 声部 .............................................................................. 力度限制 在音色模式下 ......................................................................................... ( 第 62 页 ) 在演奏音色 / 混合音色模式下 ..................................... ( 演奏音色 / 混合音色声部编辑 [F1] → [SF3] 参考号 33) • 音高从一个音符到另一个音符之间平滑的过度........................................................................ ........................
■ 存储数据 • 将已编辑的数据存储到 S90 的内置存储器 ( 用户存储 ) ...................................................... ( 第 73 页 ) • 将 S90 设置储存到存储卡................................................................................ ( 第 82 页 ) • 将 S90 设置储存到外部装置例如一台计算机........................................................ 批量复制 ( 第 72 页 ) • 储存原始音色.......................................................................................... ( 第 73 页 ) ■ 将 S90 连接到其他设备上 • 连接一台计算机................................................................
顶部面板.........................................................................................12 后背面板.........................................................................................13 安装指导 .................................................................................. 14 电源供给.........................................................................................14 开电程序 ........................................................................................14 S90 开机顺序............................
Basics Section 基本章节 控制器和接口 面板 Quick Guide 8 4 CONTROL FUNCTION PAN REVERB CUTOFF MASTER VOLUME CHORUS RESONANCE 9 @ & ! # ATTACK ¡ • MODE TEMPO PROGRAM SLOT 1 SLOT 2 SLOT 3 PRE 1 PRE 2 PRE 3 GM USER PLG 1 PLG 2 PLG 3 FAVORITES A.
ª ⁄ ‹ ›fifl ‡ °· H I J K Basics Section 后背面板 L POWER ON/ OFF BREATH ASSIGNABLE SUSTAIN 3 2 1 GREEN YELLOW ORANGE THRU OUT MIDI 2 1 IN FOOT SWITCH A/D INPUT GAIN R L ASSIGNABLE OUTPUT R L/MONO OUTPUT PHONES FOOT CONTROLLER 3.
Basics Section 安装指导 电源供给 当把 S90 作为 MIDI 接收级时: MIDI 主控设备 ( 发送级 ) Quick Guide 开电 交流电接入端口 MUSIC SYNTHESIZER Modular Synthesis Plug-in System 电源线 S90 作为 MIDI 从属设备 ( 接收级 ) 1 确认 S90 的电源开关设置为关闭状态。 Reference 2 将电源线连入背部面板的交流电源接入端口。 3 将电源线的另一端连入交流电源插座。确认 S90 使 用的电压要求和当地市电一致。 确认 S90 使用的电压要求和当地市电一致(S90 使用的电 压要求注明在背部面板上)。如果将设备接入不符合要 求的交流电将会造成内部电路严重的危害,并且会导致 触电危险! Appendix 只许使用 S90 专用交流电源线。如果专用交流电源线丢 失或受损以及需要更换,请联系阁下的雅马哈经销商。 如果擅自使用不适合的电源线替代品,将会导致火灾或 触电危险! 根据不同国家, S90 的专用交流电源线的型号会有不同 (三芯插头中有一相设计为地线)。如果不正确的连接地
在将 S90 和其他设备相连接之前,请将所有设备的电源开关设置为关闭状态。在开关任何设备的电源前,必须将所有的音量电 平设置为最小 ( 为 0)。否则,设备将会造成电击或受损。 连接外围音频设备 Basics Section 设备连接 音频设备输入 ■ 连接话筒或其他音频设备 (模拟信号输入) 阁下可以输入外部音频 (见第 44 页),只需将话筒或 音源连接连接至 A/D input 音频设备输入插孔即可。 音频设备 (合并成单声道) 将有源音箱连接到合成器背部面板的 OUTPUT L/ MONO / R( 左 / 单声道 / 右输出 ) 插孔。这样,通过调 节合成器的声相和效果设置,一对有源音箱就能够表 现出丰满的音响。 有源音箱 (左) 有源音箱 (右) 左 / 单声道 频设备输入 MUSIC SYNTHESIZER Modular Synthesis Plug-in System Reference 连接立体声有源音箱 Quick Guide 由于 S90 没设置内置扬声器,阁下需要一套外置扩音 系统或一只立体声监听耳机。以下图例介绍了不同连 接方式的方案范例;阁下可以选择自己喜欢的
连接外部 MIDI 设备 Basics Section UTILITY [F5]→[SF4] MIDI IN/OUT=MIDI 通过一个标准的 MIDI 连线,可以连接一台外部 MIDI 设备,并且由 S90 来控制它。同样的,也可以用外部 MIDI 设备 (例如键盘或音序器)来控制 S90。以下是 几套 MIDI 连接方案范例;阁下可以采用其中喜欢的 一套方案。 外部 MIDI 合成器 1 外部 MIDI 音序器 MIDI 进 MIDI 出 MIDI 进 MIDI 直通 ■ 外部 MIDI 键盘控制 S90 MUSIC SYNTHESIZER Modular Synthesis Plug-in System Quick Guide UTILITY [F5]→[SF4] MIDI IN/OUT=MIDI MIDI 出 S90 MUSIC SYNTHESIZER Modular Synthesis Plug-in System MIDI 进 MIDI 进 S90 外部 MIDI 合成器 2 Reference 如上图所示,当外部音序器 (通过 MIDI 直通)来控 制外部
■ 使用 USB 端口 关于 USB 连接头 USB 连线有不同的连接头:A 型号端口和 B 型号端口。 A 型号 端口连接计算机, B 型号端口连接 S90。 断开或连接 USB 连线以及开关电源都会造成计算机运行 中断,或使 S90 死机。注意在下列情形下不能断开 USB 连接或开关电源。 UTILITY [F5]→[SF4] MIDI IN/OUT=USB USB 连线 USB 端口 MUSIC SYNTHESIZER • 当 S90 正在识别设备或正在装载驱动程序。 • 当正在启动和关闭操作系统。 • 当系统处于暂停状态 (计算机电源管理控制休眠状态) • 当 MIDI 应用程序正在启动时。 Quick Guide 连接个人电脑后,阁下可以通过 MIDI 在 S90 和个人电脑 之间传输数据了,并且可以通过计算机对 S90 进行控制、 编辑和组织数据。例如,阁下可以通过音色编辑程序软 件来编辑 S90 的音色。还有一个特殊文件设置程序可以 让阁下通过计算机去管理 S90 插槽中记忆卡中的文件。 Basics Section 连接个人电脑 S90 如果阁下希望通过计算机音序器来遥
■ 使用 MIDI 接口 Basics Section 当发送和接收系统专用数据 ( 例如批量复制功能 ), 请采用以下设置。确保计算机软件中的 MIDI “回” 音设置为 “关”。 使用计算机的 MIDI 接口 UTILITY [F5]→[SF4] MIDI IN/OUT=MIDI MIDI 线缆 MIDI 进 当计算机中的 MIDI “回”音不出现时,请将 S90 的 Local Control (本地控制)设置为 “on/ 开”。 MIDI 出 MUSIC SYNTHESIZER Modular Synthesis Plug-in System MIDI 出 安装有应用软件的计算机 Quick Guide MIDI 进 带有 MIDI 接 口的计算机 S90 出 USB 使用外部 MIDI 接口 音频发生器 UTILITY [F5]→[SF4] MIDI IN/OUT=MIDI 键盘 进 本地设置开 回音返回开启 MIDI 接口 S90 本地控制 = 开 MIDI 出 计算机 尽管以上图例没有明确指出,实际上不管本地控制 是否设置为开或关,S90 都是接收和响应计
Basics Section 回放演示曲目 S90 拥有有大量的演示曲,可展示其动感的音色及多重功能。 DEC/NO SF1 SF2 SF3 SF4 SF5 VOICE PERFORM MASTER UTILITY CARD SEQ PLAY EDIT JOB Quick Guide 请确认合成器已经进入回放音乐模式。具体细节请查阅第 14 页 “安装指导”部分。 1 INC/YES STORE INFORMATION COMPARE F2 F3 F4 F5 F6 EXIT ENTER ARPEGGIO EFFECT BYPASS PLAY/ STOP Reference F1 EXECUTE 2 (34) 5 34 1 按 [SEQ PLAY] 键,调用 CHAIN 显示屏。 2 按 [SF5] (DEMO) 键,调用演示曲目。 Appendix 阁下可以通过 [ ▲ ▼ ] 键选择第一首曲目。 3 按 [PLAY/STOP] ( 或 [SF5]) 键开始回放演示曲目。 阁下可以设置歌曲的速度和歌曲的 (切入)位置。该操作类似
Basics Section S90 总体介绍 S90 拥有无数先进和便捷的功能。这一章节将概述这些功能。如下图描述了 S90 的各种组成模块。 控制器 键盘 MIDI 出 控制器 Quick Guide 存储卡 加载 歌曲 (SMF) 文件 S90 数据 保存 音序器 ( 回放 ) 效果器 音频发生器 AWM2 扩展琵音 回响 嵌入式 1 合唱 嵌入式 2 变种 输出 主控均衡 Reference 控制器 这个模块包含键盘,弯音轮,控制推子,等等 (见第 53 页)。 键盘本身是不产生声音的,它的功能是给 S90 音频发生器发送音符、力度和其他信息。控制器还发送非音符的演奏数据。 键盘等控制器可以将信息通过 MIDI OUT (输出)端口发送给其他外部 MIDI 设备。 Appendix 音频发生器 这个模块按照键盘等控制器发送来的信息播放音乐。如下图示描述了在音色模式中声音信号的流向路径 (见第 26 页)。 控制从 OSC (音频振荡器)单元发出的 每种因子的输出音高。 控制从 FILTER (滤波)单元发出的每种因 子输出的电平 (振幅)信号。随后信号会
S90 音频发生器拥有内置 AWM2 引擎的音频发生器和可选配扩展卡。 扩展卡 (可选配 ) 内置 AWM2 音频发生器 ● AWM2 (Advanced Wave Memory2) (高级波形记忆 2) AWM2(Advanced Wave Memory2) (高级波形记忆)是基于采样波形的合成系统,并广泛应用于众多雅马哈合成器。每一 AWM2 音色 采用多重真实声音波形采样。此外,各种不同的包络发生器,滤波器,调制器,以及各种参数都应用于在它上面。 Quick Guide Basics Section 内置 AWM2 引擎的音频发生器以及可选配扩展卡 AWM2 不局限于常规乐器,它还应用于打击乐器 (鼓),详细资料请查阅第 27 页。 S90 最多能同时安装 3 块插槽。这些扩展卡不只是简单的音色资源;它还具有音频发生器,比如复音。此外,它可以允许阁下使用除 了 AWM2 引擎之外的合成系统。您既可它当成常规内置音色来演奏它的音色,又可把它当作演奏音色部分 (见第 25 页)。 Reference ● 扩展卡 扩展卡将带给阁下无数音乐动机和力量。安装扩展卡后,它将与 S90 搭配得天衣无缝
Basics Section ● 效果扩展卡 • 人声和声扩展卡 (PLG100-VH) 安装该扩展卡后,阁下可以在选择四个效果类型中添加和声效果了。 人声基带合唱部分会自动地通过预先准备和储存好的和弦并以 MIDI 数据的方式产生出来。阁下也可以在演奏键盘时把 S90 看作是一台连接好话筒的语音合成机。 ● 多声部扩展卡 多声部扩展卡扩充了 S90 中的复音并提供了完整 16 种独立的乐器声部。通过该扩展卡回放音序器的音轨,阁下在演奏时可以 发挥出最大复音。 Quick Guide • XG 扩展卡 (PLG100-XG) 该扩展卡的核心是一只 16 声部 XG 音频振荡器。阁下可以通过这块能产生丰富多样的音色和效果的扩展卡来回放 XG/GM 歌 曲文件。 关于模块化合成扩展系统 雅马哈模块化合成扩展系统为兼容模块化扩展系统的合成器、音频发生器、以及声卡提供了强大的扩展和升级能力。这样阁下可 以方便和有效地获得最新和最强大的合成器及效果器技术,让您永远与飞速发展的现代音乐技术同步。 Reference 最大复音数 Appendix AWM2 加上扩展卡的复音最大复音数为 64 (如果安装了扩展卡
Basics Section 声部结构-音色 / 演奏音色 / 音序 演奏模式 ● 音色模式 控制模块 音色模式下的声部 Port 1 Port 2 Port 3 part 1 part 17 part 33 part 2 part 18 part 34 part 30 part 46 part 31 part 47 part 32 part 48 该音序发生器模块不适用于音色模 式。 1 - 48 声部没使用。 Reference 音频发生器模块 ( 内置 / 扩展卡 ) Quick Guide Controllers Keyboard 输出 part 3 part 4 part 5 part 16 在音色模式下, MIDI 端口号为 1。 Appendix 多声部扩展卡不支持音色模式。不过,支持其他扩展卡。 ● 演奏音色模式 控制模块 键盘 控制器 通道 (声部) 1 - 4 和 14 - 16 中最多有四条通道 (声部)能处理演奏音色模式。 音频控制器 (内置或扩展卡) PLG3 part Port 1 Port 2 Port 3
● 音序演奏模式 Basics Section 控制器模块 外部音序器 控制器 键盘 MIDI 连线无法处理多通道 (声部)的数 据。如果 MIDI 连线用于传输外部音序器 的数据,只有通道 (声部) 1 能够使用。 如果希望在 S90 上传输多通道 (声部)数 据,请使用 USB 连线。 Quick Guide 在音序演奏模式中 , 只能发声的声部才能被选用 , 并且该 声部具有同一条接收通道。 音频发生器 (样例) 音序器模块 当多声部扩展卡和两只单声部扩展卡已被安装 : MIDI 音序数据 Port 1 Port 2 Port 3 (Multi-Part Plug-in Board) (Single Part Plug-in Board) Reference Track 1 Part 1 Part 17 Part 33 Track 2 Part 2 Part 18 Part 34 Track 3 Part 3 Track 4 Part 4 Part 30 Part 46 Track 15 Part 15 Part 31 Part 47 T
Basics Section 音色和演奏音色 库 (储存器)结构 音色 演奏音色 预设音色 (384 种常规音色 + 48 种鼓组音色 ) 用户设定 (128) Quick Guide 一个音色就是一个单一的乐器声部,是由不同的参数和音色因子产生的。在音色演奏模式里 (见第 36 页),阁下可以选择和演奏任何 一种音色。演奏音色,则是混合了各种不同的音色。在演奏音色演奏模式里 (见第 41 页),阁下可以选择和演奏任何一种演奏音色曲 目。 组 A~H 预设 2 (128 常规音色 ) 预设 3 (128 常规音色 ) 预设 1 (48 鼓组音色 ) 组 A~H 组 A~H 组 A~H 组 A~C 号 1~16 号 1~16 号 1~16 号 1~16 音色 音色 音色 音色 号 1~16 演奏音色 Reference 预设 1 (128 常规音色 ) 定义音色 / 演奏音色的 “ 库 ” GM 预设音色 (128 种常规音色 ) 用户设定音色 (128 种常规音色 +16 种鼓组音色 ) GM 预设音色 (1 种鼓组音色 ) 用户设定 (128 种常
Basics Section 音色 / 音色因子 / 演奏音色 概述 每一种音色含有四个音色因子。每个音色因子本身就是一个高品质的声波或乐器声响。 音色和音色因子 每一种音色至多含有四个音色因子。音色因子是由声波制造出来的,并且音色因子的音质非常高,一个音色因子就可以充当一种音 色。由四个音色因子可以合并出非常具有表现力和富有质感的音色,阁下同样可以通过左右手单独演奏出不同的乐器音色――无需特 意建立一个演奏程序 ( 音色因子编辑 [F1] → [SF3] 音符限制 参考号 32)。 Quick Guide 演奏音色 一个演奏音色包含最多四个声部,每一声部代表一个常规色乐器音色或鼓组音色。当分配好每一声部的音色后,阁下可以通过键盘同 时演奏四个声部了。(见第 42 页) 歌曲回放设置适用于音序器播放模式的演奏设置。 Reference 一种音色 最多四个音色因子 一种演奏音色 最多四个音色 音色因子 1 - 4 + 每一声部不同的音色 一个声部 + 音色 公共编辑参数 声部编辑参数 + ( 通道设置影响所有 的声部 ) 公共编辑参数 Appendix 一个混合 (模式)(
S90 拥有两种音色:常规音色和鼓组音色。常规音色大体上为音高乐器类型,并且每一个声音都由与其音高相匹配的音键来匹配。鼓 组音色大体上为打击乐器和鼓,而它们的声音是特定的音符音键来匹配的。 鼓组音色 Quick Guide 常规音色 音色 音色因子 1-4 音键 1 音键 2 音键 3 音键 4 音键 5 Basics Section 常规音色和鼓组音色 音键 76 GM 是全球音色组织机构指定的全球统一标准规范。 GM 的设计初衷是为了保证 MIDI 数据能在不同厂家不同型号的设备 中使用的通用性。 S90 中的 GM 音色库专为播放 GM 曲目而设。不过,请要记住音色可能与原始音源上的音色不完全一 致。 Appendix 内置存储器和文件管理器 在这一部分,如何存储各种类型的数据和如何使用存储介质来存储它们。 下面这个图例描述了 S90 相关的一些功能以及内置存储器和存储卡。 S90 内置存储器 * 批量数据传输不适用于传输用户设定的琵音 以及系统设定的声部。 预设数据 内存 • 音色 • 扩展音色 • 预设琵音 • 演示曲目 * 音色和演奏音色专用 外部 MIDI 设备
内置存储器 Basics Section ● ROM ( 只读存储器)和 RAM (可读写存储器) ROM (Read Only Memory 只读存储器 ) 被设计为只能读取数据但不能写入数据的存储器,存储器里预设的乐器数据永存不变。相反, RAM (Random Access Memory 可读写存储器 ) 即可读取数据也可写入数据。 ● Flash ROM (闪存)和 DRAM( 内存 ) 闪存中的数据即使在关电情况下都能随时读写和修改。相反, DRAM (内存)里的数据在关电情况下就会丢失。这样,阁下需要在关 电前经常将内存里的数据储存到闪存或存储卡中。 Quick Guide 当数据正在向闪存中写入 (当 "Executing...
Basics Section 基本操作 在该章节里,阁下将能了解到 S90 的模块结构、面板显示屏指示以及操作原理。 模式 音色模式 主控模式 MODE 音色 演奏 模式 音色 编辑 模式 音色 工作 模式 音色 储存 模式 VOICE PERFORM Quick Guide S90 拥有不同的模式,每一模式具有不同的操作设置和功能设置。 主控演奏 模式 主控 编辑 模式 主控 工作 模式 主控 存储 模式 MASTER 音序演奏模式 演奏音色 演奏 模式 演奏音色 编辑 模式 演奏音色 工作 模式 演奏音色 储存 模式 UTILITY CARD EDIT JOB SEQ PLAY 设置模式 音序演奏混合模式 音序演奏混合 编辑 模式 音序演奏混合 工作 模式 Reference 演奏音色模式 插卡模式 STORE 编辑模式 储存模式 COMPARE Appendix 工作模式 模式例表 演奏 编辑(LED灯) 工作 (显示) STORE (Displayed) 音色 (LED灯) 第 36页 第 60页 第 70页 第 73页 演奏、编
Basics Section 选择一种模式 显示屏提示 对于演奏音色、音色以及音序演奏模式都有不同的演奏模式。 按下适当的模式按钮就能进入相应的演奏模式中去。 在这里,我们将指导阁下如何阅读显示屏中的提示信息。 音色演奏模式 在音序演奏模式里,有一种混合模式。如果需要进入该模式, 只需在选择好音序演奏模式后按下 [F6] 按键即可。 4 5 1 Quick Guide 如果需要进入主控模式,可以按下 [MASTER] 按键。此时, VOICE/PERFORMANCE/SEQ PLAY 指示灯发光。 2 3 6 演奏音色、音色、主控、混合设置又可分编辑模式和工作模式 两种。点按 [EDIT] 或 [JOB] 即可进入编辑或工作模式。 音色演奏模式 (快速编辑) 12 此外,还有一个设置模式,它是用来对设备和插卡模式进行整 体设置的,它含有与插卡相关的设置。 2 3 4 1 9 Reference 切记在调用子模式前,主模式被激活的状态下,不支 持设置模式的特殊显示和参数。 混合设置的音符可通过 "Put" 功能 (而不是 "Store" 功能)记忆下来。 音色编辑模式
分配给主控的模式 指示 分配给主控的音色库 号指示 1 2 存储模式 5 Basics Section 主控演奏模式 23 6 命名清单 2 4 1 Quick Guide 主控快速编辑模式 13 2 ! 1 模式 (PERF=PERFORMANCE 演奏音色 ) 4 2 库 / 号 P1-P3 = 扩展卡 1 -扩展卡 3 1 Reference 主控编辑模式 3 种类 (见第 35 页) 4 名字 (有关单独数据表) 5 键盘MIDI传送通道(见第37页)。通过八度音程参数来设 置键盘 % ^ 6 分配给各自的控制推子功能 (3 个)。 AS=ASSIGN (分配) (见第 53 页) & Appendix 音序演奏模式 7 功能 (通过 [F1]-[F6] 按键选择) 1 8 子功能 (通过 [SF1]-[SF5] 按键选择) $ 9 参数或功能名 (见第 98 页) ¡ * ( º 10 设置 11 编辑类型 COMMON=Common Edit status 公共编辑状态 EL1-EL4=Element Edit statu
使用子功能按键 [SF1] - [SF5] Basics Section 选择功能和参数 以上每一种模式在不同的功能和参数环境下都呈现出不同的显 示,阁下可以通过这些显示以及 [F1] - [F6] 、[SF1] [SF5] 按键来 选择期望的功能。 当阁下选择了一种模式,相应的显示或菜单将出现在显示屏底 部的按键上。 这些功能可以通过相应的按键 [SF1] [SF5] 来实现。 Quick Guide 使用功能按键 [F1] - [F6] SF1 这些功能可以通过相应的按键 ([F1] [F6]) 来实现。 F1 SF2 F2 SF3 F3 SF4 F4 SF5 F5 INFORMATION F6 在这个样例中,点按 [SF5] 键会出 现 SCALE 显示 Reference 依照目前选择的模式,至多五个功能 (子功能)可以通过按键 ([SF1] - [SF5]) 来被调用。注意并不是所有的功能都如此。(有 些显示的按键中并不包含子功能)。 SF1 F1 SF2 F2 SF3 F3 SF4 F4 SF5 F5 INFORMATION F6 如
数据输入 更改 (编辑)数值 信息显示 如果需要取得一个被选模式的相关详细信息,只需点按 [INFORMATION] 按键即可轻松快捷地调取出来。例如, 音色模式被激活,阁下可以快速地检查关于哪一个音色 库被选择了、使用的是哪一种演奏模式 (立体声还是单 声道)、选用的是哪种效果等信息。 Basics Section 基于显示屏的控制 DEC/NO INC/YES EXIT ENTER Quick Guide 顺时针旋转该数据转盘将增大数值;反 之,逆时针旋转该数据转盘将减小数 值。 阁下可以在按住 [INC/YES] 按键的状态 下同时点按 [DEC/NO] 按键,将以 10 倍的步长来快速增大数值。如果希望以 10 倍的步长来快速减小数值,则按住 [DEC/NO] 按键的状态下同时点按 [INC/ YES] 按键来实现。 INFORMATION EXECUTE 移动指针 (光标) 在音序模式中,阁下可以确认 (当前)选择的文件夹 (目录)。 Appendix 当阁下从使用模式或收藏类型功能中退出时,显示 屏中所改变的参数会自动地储存起来。然而,如果 没有正常退出就关电,那么这些编
音符 (音键)设置 1 通过指针按键移动光标至名字的第一个位置。 Basics Section 个别的几个 S90 参数是将一个音键设置为一项功能―― 例如,设立分割键盘――通过指定的音符数值设置为分 割点。阁下可以通过 [INC/YES] 和 [DEC/NO] 键或数字转 盘来设置这些参数,或直接点按音键输入数值。例如显 示屏显示如下,音色中的音色因子 1 正在被编辑。 DEC/NO INC/YES EXIT ENTER EXECUTE Quick Guide Reference 当选择了音符制定, [KBD] 标识将出现,表示阁下可以通过键 盘设置数值了。按住 [INFORMATION] 按键的状态并同时点按 INFORMATION 相应的音键。 2 通过 [INC/YES] 按键、[DEC/NO] 按键或数字转盘选择 一个字符。 DEC/NO INC/YES Appendix 命名 (输入字符) S90 允许创建自己设计的诸如音色、演奏音色、主控之类 的数据。也可以自由的为它们命名。 • 用户音色 • 用户演奏音色 • 用户主控 • 混合模式 • 文件存储至存储卡 第
当光标移动到 Name 的位置,[LIST] 图标将显现出来并且阁下可以通过 按住 [INFORMATION] 键来调用字符表。释放 [INFORMATION] 键将返 回到原始显示状态。 参数类型 ( 绝对值和相对值 ) 我们有很多方法来设置参数。一些参数需要我们直 接输入数字和字母。此外,一些参数类型是 " 绝对 值 ",而另外一些是 " 相对值 "。 例如,绝对值参数在下图例中可设置:单声道 " 或 " 多声道 "。还有例如音量参数,我们可以设置从 0 至 127 之间的任何数值。音量设置 ( 如下图左边部分 ) 和实际发生的音量是线性的,一一对应的。而图中 底部显示的是力度偏移参数, " 偏移量 " 则是在实际 音量的基础上增加或减少的数值。该值直接作用于 我们在操作键盘时的音符力度。有时,这些参数又 是一个百分比。 Reference INFORMATION Quick Guide 在以上 2 和 3 步中,可以使用专门的弹出式字符表,该 表为您展示出几乎所有能用到的字符,让您非常方便快 捷地输入字符。如果希望选择一个字符,按住 [INFORMATION] 按键并使用 [INC/YES]
Basics Section 快速指导 演奏音色 在这里,阁下可以掌握如何通过 PRESET1-3( 预设 ),GM,USER( 用户 ) 以及 PLG 1-3( 扩展卡 ) 存储组 ( 库 ) 中选择和演奏音色。 有关音色的详细资料,请查阅第 25 页。有关音色表的信息,请查阅数据表分册。 Quick Guide 至多 128 种常规音色和 16 种鼓组音色存储在用户存储器里 ( 见第 25,27,73 页 )。音色设置可以在音色编辑模式下变更 ( 见 第 60 页 )。 选择音色 4 1 3.
B C D E F G H SYN LEAD SYN PAD/ CHOIR SYN COMP CHROMATIC PERCUSSION DRUM/ PERCUSSION SE MUSICAL FX COMBI 4 选择音色号。 减少数值 增加数值 DEC/NO 减少数值 1 2 3 INC/YES 增加数值 4 5 6 7 8 12 13 14 15 16 ELEMENT / PERF.
Basics Section 使用音色类别搜寻功能 S90 具有音色类别搜寻功能,能让阁下快速找到您期望的音色,而不用关心该音色所在的哪个音色库。简单地选择一个音色类别 - 如 钢琴音色,这时您可以在所有地相关音色中一浏览和试听。另外,阁下可以使用特殊收藏音色类别将经常使用和钟爱的音色储存起 来。 3 3.
当阁下从音色收藏类退出时,显示屏中被阁下变更 的参数将被自动地储存起来。然而,如果阁下没有 等系统完全退出就关电,该编辑数据将会丢失。 1 选择所需的音色 ( 见第 36 页 )。 2 按下 [F4] - [F6] 按键来选择阁下需要编辑的菜单并编辑 参数。 当选择了一个扩展音色 ( 当已经安装好单声部扩展卡 ), 阁下可以按下 [F2] 按键来调用音色库。 3 往用户存储器里储存第 2 步的设置。 4 点按 [F1] 按键返回原始显示状态。 一些参数需要特殊音色扩展卡才能编辑。 当数据正在向闪存中写入 (当 "Executing...
● [F2] 音色弹奏 扩展卡音色库 ● [F6] 音色演奏 琵音 Basics Section 在这个显示屏中,您可以选择扩展卡音色库中的特殊 音色库,然后确定是使用扩展音色还是使用 " 原始 " 音色。简单的说 , 两种类型的区别主要在以下几方面: • "原始"音色是扩展卡中未经过处理和改变的音色― ―扩展卡音色的 " 原材料 " • 扩展卡音色是被编辑过的音色――已被特殊编辑和 处理过并最适合于 S90 的音色。 该显示含有对琵音的基本设置,包括种类和速度 (见 第 45 页)。 关于扩展音色和原始音色 Quick Guide S90 扩展卡中的音色可分为两种:原始音色和扩展音色, 原始音色是未经过处理和改变的音色―扩展音色的 “原 材料”。扩展音色,相反,是被编辑过的音色―已被特殊 编辑和处理过并最适合于 S90 的音色。 这些原始音色是一套特殊的音色―称之为原始自定义音色 ―该音色可以被与 S90 相连的计算机加上扩展卡中的特殊 编辑软件来编辑。(见第 73 页)。 扩展音色 Reference ❏ 设置 (插槽 1 中已安装好扩展卡 ) PLG1USR (User Plug-i
Basics Section 弹奏演奏音色 在演奏音色模式中,阁下可以选择和播放个人的用户演奏音色。 有关演奏音色和演奏音色记忆 (库)结构,请查阅第 26 页。 3 1 3.
3 选择一个演奏音色号。 Basics Section 独奏声部 1 1 2 3 4 5 6 7 2 3 4 5 6 7 8 12 13 14 15 16 TRACK SELECT 8 ELEMENT / PERF.PART / ZONE ELEMENT / PERF.
SF1 F1 SF2 SF3 F2 F3 SF4 F4 SF5 F5 阁下可以在键盘的低音区点按所要指定的音键同时按住 [SF4] 按键,为低音音键设置音色。而高音区则点按点按 所要指定的音键同时按住 [SF5] 按键。 这样阁下就创建了一台具有最多 4 个音区分布 4 个不同声 部(音色)的分割键盘。同样阁下也可以在键盘上层叠声 部。 Basics Section 3 如有必要,指定每一个声部的音键。 Quick Guide 1 演奏音色弹奏模式下点按 [F3] 按键, 调用音色显示屏。 INFORMATION F6 音符 ( 音键 ) 下限 音符 ( 音键 ) 上限 SF5 Reference SF4 2 给每一声部分配音色。 DEC/NO 4 改变每一声部的音量以及调整四个 声部的相对平衡。 INC/YES 编辑提示 (见第 39 页) 为被选中的声 部分配内置音 色。 SF1 F1 当 CONTROL FUNCTION (控制功能 )被设置为 VOLUME (音量),阁下可以使用控制推杆对每一个声 部的音量进行调节。 SF2 F2 SF3
Basics Section 在演奏音色弹奏模式编辑 演奏音色 (快速编辑) 演奏音色弹奏模式可以让阁下为选中的音色进行各种 常规地编辑操作。如需进行更细致和更全面的编辑操 作,请使用演奏音色编辑模式。 演奏音色弹奏模式以及演奏音色编辑模式里含有相同 的参数名、参数功能、参数设置。 Quick Guide ● [F2] 演奏音色弹奏 A/D (模拟 / 数字) Reference 在该显示屏中,阁下可以为 A/D 输入音色进行设 置。 A/D 输入的功能即让阁下输入外界的声音 (比 如来自话筒或吉他的声音),然后对声音进行处理 以及和 S90 中的其他声音进行混合。声音信号可以 通过 A/D 输入插孔或 mLAN 端口输入至 S90 (如 果 S90 已经安装了可选配模块 mLAN8E)。 有关具体连接的详细资料,请查阅第 67 页)。 在设置模式阁下可以通过设置来选择是采用 A/D 输入 插孔,还是采用 mLAN8E 端口。([F2] - >[SF1] 数模 音源, 参考号 53)。 • Volume 音量 指定 A/D 输出的电平值。 Appendix • Pan 声相 指定 A/D 声部的
该功能能依照阁下演奏的音键自动地触发预设的琵 音。 非常适合 dance/techno 舞曲类型的音乐。阁下可以将 自己钟爱的琵音类型分配到每一音色或弹奏音色上 去,并调整速度。同样阁下也可以设置琵音回放方 式,力度范围和播放效果,创造自己设计的风格。不 只这些,琵音回放可以通过 MIDI 输出端口来传送 ( 参 考号 86), 这样,可以在音序器上录下琵音数据,并且 可以通过其他音频发生器来播放。 琵音开 / 关 (当歌曲回放时) 一首歌曲的每一声部 (混合模式)都可以单独设 置琵音开 / 关。 ( 见 79 页 )。 Quick Guide 什么是琵音功能? Basics Section 使用琵音功能 琵音的四个回放类型 琵音构造 Sq: 音序 创建常规的琶音乐句。大体上是上行 / 下行八度。 如下图例描述了琵音的构造。 音色 琵音数据 预设 1 (128) 在演奏音色模式 下 演奏音色 琵音 音色 音色 演奏音色 预设 2 (128) 演奏音色 琵音 音色 音色 Dr: 鼓模板 该类型主要为鼓和打击乐音响而设计。 Ct: 控制 通过控制变化数据来实现动态的音高和力
Basics Section 琵音回放 1 选择一个音色或演奏音色 (见第 36、 41 页)。 琵音类型,速度和音高范 围 S90 提供了多种不同的琵音类型,阁下可以改变琵音的 速度。 琵音功能适用于所有的模式。 下面文章将描述琵音在演奏音色模式中的应用。 Quick Guide 2 点按 [ARPEGGIO] 按键开启琵音。 ARPEGGIO EFFECT BYPASS PLAY/ STOP 1 在演奏音色模式里点按 [F6] 键,调用 ARP(Arpeggio 琵音 ) 显示屏 。 Reference 当阁下选中了一个音色或演奏音色并将琵音开 关设置为开启, [ARPEGGIO] 按键会自动地开 启。 [ARPEGGIO] 按键的开关状态能被储存到每一个音色或 演奏音色设置中去。 3 演奏键盘。 SF1 F1 SF2 F2 SF3 F3 SF4 F4 Appendix 如果按住音键,琵音将依照演奏音符、琵音类型、速 度、力度范围设置等参数来执行。 在音色演奏模式里,琵音将作用于被选的音色上。 在演奏音色 / 混合模式里,当被选声部对应的 琵音开关设置为开启时,琵
Basics Section 4 设置琵音回放的速度。 移动光标至速度参数并选择。 5 设置琵音回放的力度范围。 下限 Quick Guide 移动光标至力度范围参数并选择。 上限 Reference 只有音键演奏的力度在该范围内时,琵音来能 发挥作用。 127 上限 下限 Appendix 0 6 设置琵音声部开关 (只适用于演奏音 色)。 阁下可以为每一声部设置琵音回放开关。移动光标至 希望选中声部的方框中,并复选该框开启该声部的琵 音。 7 储存用户演奏音色的琵音设置 (见第 73 页)。 使用琵音功能 47
Basics Section 作为主控键盘使用 什么是主控模式? 四个音区 Quick Guide S90 装载了大量的功能和操作,阁下可能在查找和调 用某一特殊功能感到比较麻烦。如果运用主控模式, 这样阁下就可以将经常执行的操作储存起来,并只需 点按一个按键即可随时立即调用它们。 S90 提供了容 纳总共 128 条用户主控设置空间。 主控号 设置样例 主控 001 音色模式 音色号 102 主控 002 音色模式 音色号 88 主控 003 演奏音色模式 演奏音色号 043 * 音区开关关闭 主控 004 演奏音色模式 演奏音色号 059 * 音区开关关闭 在主控模式中,键盘可以分割出最多 4 个独立的音区― ―每一音区带有各自的 MIDI 通道设置。这样,阁下可 以只使用一只键盘单独控制几个不同的乐器声部。而 且,阁下可以让这些单独音区来控制与其相连的 MIDI 设备。还可以在用户主控模式下设置和储存这四个音 区。 内置音频发生器 (包括扩展卡)的每一通道的 MIDI 通道只适用于音序演奏模式。 Reference 演奏音色模式 演奏音色号 077 * 音区开关开启
1 进入主控模式。 Basics Section ■ 分割 阁下可以使用音区设置建立一个 “分割”―以一个音 键作为分割点,将将键盘分割成两部分音区。 MODE 如以下样例,该键盘的分界点为 C3 音键,这样划分出 来的低音音键区域将弹奏琵音,高音音键区域依然弹 奏常规音色。 Quick Guide 高音部分 通道 2 声部 2 演奏音色 通道 1 声部 1 演奏琵音 MASTER 2 选中一个主控号。 1 ■ 层叠 阁下同样可以使用层叠设置来创建一个 “分层”―这 样键盘能同时演奏两个不同的声部。 如以下样例,键盘能同时齐奏出两种音色―一种内置 音色和一种扩展音色。 2 3 4 5 6 7 8 12 13 14 15 16 Reference 分界点 (C3) PERFORM ELEMENT / PERF.
Basics Section 主控储存 在主控演奏模式中,选中的模式以及程序将被储存到 主控中。 4 储存选中的程序或模式 (见第 36 至 38 页)。 1 进入主控模式并选中一个主控号 (见第 49 页)。 DRUM KITS DEC/NO Quick Guide 2 点按 [F2] 按键,调用储存显示屏幕。 INC/YES PRE 1 PRE 2 PRE 3 GM USER PLG 1 PLG 2 PLG 3 FAVORITES A. PIANO KEYBOARD ORGAN GUITAR/ PLUCKED BASS STRINGS BRASS REED/PIPE COMMON A B C D E F G H SYN LEAD SYN PAD/ CHOIR SYN COMP CHROMATIC PERCUSSION DRUM/ PERCUSSION SE MUSICAL FX COMBI 1 2 3 4 5 6 7 8 12 13 14 15 16 或 ELEMENT / PERF.
2 开启音区开关。 在以下样例中,我们将建立三个音区,显示如下。我们 将 C3 音键设定为分界点。在低音区(B2 音键和 B2 音 键以下音区),会出现低音音色和镲片音色。在高音区 (C3 音键和 C3 音键以上音区)会出现钢琴和电颤琴的 音色―通过外部 MIDI 音频发生器播放。运用这种经典 的设置,阁下只需您的双手就能轻松地演奏出能和一 只完整的爵士乐队媲美的音乐。 DEC/NO INC/YES EXIT ENTER Basics Section 使用音区―与外部音频发生 器一起创建层叠 / 分割 Quick Guide EXECUTE 如以下样例,我们将运用主控模式的音色。 音区 2 3 进入主控编辑模式。 Reference ( 钢琴 ) 音区 3 音区 1 ( 电颤琴 ) ( 贝斯 和 镲片 ) EDIT JOB STORE COMPARE 外部音频发生器 C3 公共编辑和单独音区编辑 1 在主控演奏模式中选择音色 将模式设置为音色,然后选中 PRE1 音色库和 voice (音色)123。 如果希望让编辑参数成为所有音区的公共编辑, 请点按 [
5 调用 TRANS 显示屏。 1 设置音色范围音区 1 的上限音符为 B2。设置音色范 Basics Section 围音区 1 的下限为 C-2。 2 设置音色范围音区 2 和音区 3 的上限音符为 G8。 设置音色范围音区 2 和音区 3 的下限音符为 C3。 每一音区会在以上音符范围内产生被分配的音色。 如有必要,阁下同样可以设置其他参数。 SF1 Quick Guide F1 SF2 F2 SF3 F3 SF4 F4 SF5 F5 INFORMATION 7 储存该设置至主控 (见第 73 页)。 F6 1 设置开音频发生器关至音区 1 并且将其他所有音区 Reference 都设置为关闭。这样只有音区 1 的演奏数据影响于 S90 的音色,而其他音区则无法进行。 2 将音区 2 和音区 3 的 MIDI 开关开启,其他的则关闭。 这样音区 2 和音区 3 的演奏数据将传送至外部音频 发生器中去。 3 将音区 1 的 MIDI 传送通道设置为 1。将音区 2 和音区 3MIDI 传送通道的设置与外部音频发生器 (从属设 备)的接收通道相匹配即可。 控制号
弯音轮和调制轮 控制推子 (CS) 弯音轮的设计初衷是控制音高。上下推动弯音轮能上 下改变音高。 调 制 轮 通 常 用 于 增 加 调 制 效 果 (颤 音、滤 波 变 种、 等)。 当阁下在演奏时,这些推子可以实时变化声音的不同 方面。阁下可以改变选择特殊的功能组,也可以改变 通过 [CONTROL FUNCTION] 按键指定的推子参数。 选中的指定组 (A, B, 1, 2)能让阁下控制一组用户 指定性功能。 弯音轮 当阁下选择了一个特定程序,您也可以确定哪条 控制行被自动激活。( 参考号 12, 58)。 调制轮 推子 [A] 和 [B] 分配了 公共系统参数。([F4] → [SF2] 参考号 128)。推子 [1] 和 [2] 分配了音色 专用参数。(见第 55 页)。 下移 每一音色都已分配了预设的参数设置。使用推子 [1] 和 [2] 在一定程度修改了这些设置。如果这 些参数已经以它们的最小值和最大值设置的,那 么这些设置无法被处理。 深 PITCH MODULATION 每一种音色和演奏音色的弯音范围都可以被设置 (参考号 14)。弯音轮也可以被赋值为其他参数。
Basics Section 踏板控制器 控制推子设置的样例 1 点按 [CONTROL FUNCTION] 按键,选择希望 控制的功能条。随即相应的指示灯发光,提示 阁下该功能条被激活。例如,如果阁下希望使 用推子去控制声相、混响、合唱和速度,请点 按 [CONTROL FUNCTION] 按键 (若有必要, 重复点按)直到显示屏顶部的指示灯发光。 Quick Guide 1 .声相,效果传送以及速度 2 .滤波和 EG (包络发生器) 3 .分配指定 4 .主控 EQ (均衡) 5 .音量 6 .音区 重复点按该键, 选择每一条功 能.
信号源 控制信号源 PB, MW, 等 .
■ 控制组和外部 MIDI 控制 Basics Section Quick Guide 在一套控制组里,控制器将分配合成器内部参 数。然而,起初一些控制器是为某一特别的用途 而设计的,只能传送预先定义好的 MIDI 控制变 化信息。 比如,弯音轮、调制轮以及键盘触后 (键),当 初的设计只是将控制弯音、调制和触后的信息传 送到 MIDI 输出。而在控制组里,如果将声相参 数分配到弯音轮,那么只要推移弯音轮,合成器 的内置音频发生器就会改变声音的声相位置,然 而需要注意的是:在此同时,弯音轮预先定义的 原始信息仍被传送至 MIDI 输出。 \ MIDI OUT IN 主要控制号及功能 踏板开关 弯音轮/可分配控制器/控制踏板 (变量控制) 7 音量 64 持续1 10 声相 65 延音开关 11 表达 66 持续 71 和声 (谐振) 96 琵音开关 72 释放时间 97 琵音持续 73 触发时间 98 播放/停止 74 明亮度 99 程序变化增加 75 衰减时间 100 程序变化减少 91 混响输出电平 101 音键复原 93 合唱输出电平 见第 119 页
建立 2 在 MIDI 菜单下调用 OTHER (其它)显示屏 ([F5] → [SF4])。 3 移动光标至 MIDI IN/OUT(MIDI 进 / 出)参数 的位置并将 MIDI 进 / 出端口设置为 USB。 4 在 CTLASN 菜单中调用 REMOTE(遥控)显 示屏 ([F4] → [SF4])。 5 选择模板类型,然后点按 [ENTER] 按键。 在使用遥控功能之前,阁下需要先按照以下描 述建立一套系统。 1 用USB连线将计算机和S90连接起来。 见第 17 页。 在计算机上装载 USB MIDI 驱动和音序软件的 安装文件 (含在 CD - ROM 中)。有关具体如 何装载的详细资料,请查阅安装指导手册分册。 3 为 S90 中设置模式下的音序软件选择 一个模板。 1 进入设置模式。 UTILITY CARD Basics Section Appendix 2 装载安装文件。 Quick Guide 遥控功能可以让 S90 面板上的硬件控制来控制计算机里音序软件的基本操作。通过 S90 的推子可以 对音轨哑音,控制音序器 (播放 / 停止),合并 MID
Basics Section 使用遥控功能 3 使用控制推子来控制音序器中音轨的电平值 (见第 59 页)。 1 点按 [REMOTE CONTROL] (遥控)按键 CONTROL FUNCTION 开启遥控功能,这时该按键上的指示灯闪烁。 PAN REVERB CHORUS TEMPO CUTOFF RESONANCE ATTACK RELEASE ASSIGN A ASSIGN B ASSIGN 1 ASSIGN 2 MEQ LOW MEQ LOW MID MEQ HI MID MEQ HIGH VOLUME 1 VOLUME 2 VOLUME 3 VOLUME 4 ZONE 1 ZONE 2 ZONE 3 ZONE 4 CS 1 CS 2 CS 3 CS 4 MASTER VOLUME REMOTE CONTROL Quick Guide 2 如有必要操作 S90 面板上的推子或按键。 4 在音序器中控制传送功能。 Reference 1 在阁下计算机的音序软件里选中一条音轨。 S90 的 [1]~[16] 按键分别对应于计
软件名:Logic Audio Platinum Ver5 当模板被设置为 “Logic,”下列功能能够由 S90 来遥 控。 这些用来控制通过 [1] - [16] 按键选择的音轨。 每一参数 这些用来控制通过 [1] - [16] 按键选择的音轨 每一参数 通过 [CONTROL FUNCTION] 按键设置 控制推子 1 第1行 声相 传送 1 传送 2 传送 3 第2行 声相 均衡 1 频点 均衡 1 增益 均衡 1 Q 值 第3行 声相 均衡 2 频点 均衡 2 增益 均衡 2 Q 值 声相 均衡 3 频点 均衡 3 增益 均衡 3 Q 值 第4行 控制推子 2 控制推子 2 控制推子 4 选中的音轨 控制推子 1 控制推子 2 控制推子 2 控制推子 4 1~4 音量 1 音量 2 音量 3 音量 4 5~8 音量 5 音量 6 音量 7 音量 8 9 ~ 12 音量 9 音量 10 音量 11 音量 12 13 ~ 16 音量 13 音量 14 音量 15 音量 16 音序传送 这些用
Basics Section 音色编辑 下列程序展示了创建和编辑音色的基本原则。 当然,在该例子中,阁下可以为其自由地设置参数。有关每一参数地详细资料,请参阅本手册中的相关章节 (见 第 98 页)。 所有的参数设置将连同音色本身一起被存储起来。 Quick Guide 1 1 选择一个用来编辑的音色。 在音色演奏模式里,选中阁下所希望编辑的音色。 点按 [VOICE] 按键进入音色演奏模式。 2 MODE 进入音色编辑模式。 Reference 3 选择公共参数 ● 对音色中的所有单元设置公共参数 (音量,音高 等),阁下也可以设置有关琵音、控制、效果等参 数。 Appendix 4 选择单元参数 ● 从 OSC (振荡器)显示屏中,选择作用于音色因子 的音频,也可设置音量、声相、音高范围等其它基 本参数。 ● 从 PITCH (音高)显示器中,选择作用于音色因子 的音高调节以及其它与音高有关的参数。如有必要 也可设置 PEG (Pitch Envelope Generator 音高包络 发生器)。 ● 从 FILTER (滤波)显示器中,调整作用于音色因子 的滤波参数。如有必要也可
1 点按 [F1] - [F6] 以及 [SF1] - [SF5] 按键来选择阁 点按 [DRUM KITS] 按键即可对所有四个音色因子 进行共同编辑了 (该按键在这里理解为 “公共” 按键)。 DRUM KITS COMMON 如需单独对每个音色因子进行参数编辑,点按与希 望处理音色因子相对应的数字按键 ([1] - [4]) 即可。 3 音色因子选择 10 3 使用[INC/YES] 和[DEC/NO]按键设置每一参数 的数值。 有关编辑提示的具体详情,可以查阅第 39 页。 11 通过该功能可以在阁下编辑过的音色 / 演奏音色 和未编辑 (编辑之前)的音色 / 演奏音色之间进 行比较。 1 在编辑模式下点按 [COMPARE (EDIT)] 按键。 EDIT 指示灯将会闪烁,先前编辑的设置将会 临时恢复。 ( 提示将在显示屏顶部 提示显示的地方显 示出来。 ) 4 ELEMENT / PERF.
3 设置公共参数 Basics Section 每一种音色包含最多 4 个音色因子。在这里,将阐述 对这所有音色因子进行共同处理的公共参数。 ● 通用参数 [F1] 在公共编辑中设置通用参数,比如音色名。 4 设置音色因子参数 音色因子编辑过程 Quick Guide PEG FEG AEG PITCH FILTER AMP 音色因子 1-4 ● 输出 [F2] 设置音色输出参数,比如输出电平 (音量)和声相位 置。 振荡器 OSC ● ARP( 琵音 )[F3] 为音色设置琵音的参数 ( 见 第 45 页 )。 Reference ● 控制设置 [F4] 该面板 / 背板上的控制器分配不同的功能。例如,给 弯音轮和控制踏板分配参数,这样可以实时改变音色 的音质。 ● LFO 低频振荡器 F5] LFO 使用了一个低频波形来改变音高 / 滤波 / 功率放大 特性,创建出颤音、哇音等效果。 Appendix ● 效果器 [F6] 效果器参数含有两种嵌入式效果器和两种系统效果器 (混响和合唱)。 LFO ● OSC ( 振荡器 ) [F1] 阁下可以设置不同的参数来控制音色
PEG (Pitch Envelope Generator 音高包络发生器 ) [F2] → [SF3] 当一个音键被按下时,阁下可以通过 PEG 来调节音高 的转变。如下图,音高包络由五个时段 (转换速度) 参数和五个电平 (音高)参数组成。这对于产生音高 自动变化非常有用。此外,不同的音色因子可以分别 设置为不同的 PEG 参数。 截止频点和谐振 滤波工作原理是允许低于指定频点 (截止频点)的声 音信号通过,而高于指定频点 (截止频点)的声音信 号则被过截除。这样,阁下可以通过设置截止频点来 制造出明亮的和黯淡的声音。谐振,则是提升截止频 点的电平值。在该区域通过谐振泛音,可以制作一个 特别的 “ 峰”音,使声音变得明亮和富有穿透力。 电平 Reference 截止频点 频率 (音高) " 通过 " 的信号部分 显示屏中一些参数的全称呈现如下: Basics Section ● FILTER 滤波 [F3] 阁下可以通过滤波来调整音色因子里声波的泛音 (谐 波)来改变每一音色因子的特性。 Quick Guide ● 音高 [F2] 阁下可以为每一音色因子设置基本音高。阁下可以使 用音高调
Basics Section LPF24A (Low Pass Filter 24dB/oct Analog) 模拟 24dB/oct 低通滤波 器 具有基于模拟合成器特性的 A 4-pole (-24db/oct) 动态低通滤波器。 BPF12D (Band Pass Filter 12dB/oct Digital) 12dB/oct 数字式 带通滤波器 电平 带通范围 谐振 -12db/oct 频率 滤波范围 Quick Guide LPF18 (Low Pass Filter18dB/oct) 18dB/oct 低通滤波器 A 3-pole (-18db/oct) 动态低通滤波器。 LPF18s (Low Pass Filter [18dB/oct Staggered] 交错式 18dB/oct 低通 滤波器 还是 A 3-pole (-18db/oct) 动态低通滤波器,但频率曲线较平坦。 滤波范围 BPF12s (Band Pass Filter 12dB/oct Staggered) 交错式 12dB/oct 带通滤波器 基本上和 BPF12D 一样,只是频率曲线较平坦。 BPF6
LPF12 (Low Pass Filter 12dB/oct)+ BPF6 (Band Pass Filter) 12dB/oct 低通滤波器+带通滤波器 并列合并了 12dB/oct 高通滤波器和高通滤波器。 电平 距离 电平 Basics Section Dual HPF 双高通滤波器 并列合并了双 -12dB/oct 高通滤波器 频率 在显示屏中可以设置两个截 止频点之间的频率间隔距离 Dual BPF 双带通滤波器 并列合并了双 -6dB/oct 带通滤波器。 Quick Guide 频率 直通 该滤波器将信号未做修改全部旁通。 电平 在显示屏中可以设置两个截 止频点之间的频率间隔距离 .
Basics Section ● AMP (Amplitude 功率放大器 ) [F4] 阁下在完成对 OSC (振荡器)、音高和滤波等参数的 设置之后,可以设置每一个音色因子的输出音量。 声音信号中不同音色因子将被指定不同的音量而传送 至下一个效果单元。 同样,也可以通过设置 AEG (Amplitude Envelope Generator 振幅包络发生器 ) 全程控制音量变化。 Quick Guide AEG (Amplitude Envelope Generator 振幅包络发生器 ) [F4] → [SF3] 当一个音键被按下时,阁下可以通过 PEG 来调节音量 的转变。如下图,振幅包络由四个时段 (转变速度) 参数和三个程度 (过滤程度)参数组成。当阁下点按 了一个键盘音符,音量将会依照这些包络设置来变 化。这对于制作一个自动哇音设置非常有用。此外, 不同的音色因子可以设置不同的 AEG 参数。 5 设置效果参数 在第 67 页中,将例举如何运用效果器。 6 储存编辑音色 内置用户存储器可以储存至多 128 条崭新 / 常规编辑 音色和 16 条崭新 / 编辑鼓组音色。 音色 储存 常
S90 的效果处理分如下几个单元。 ■ 系统效果器 (混响、合唱、变种) 系统效果器作用于整个声音信号,比如是一条音色、 一个完整的演奏组合,一首歌曲等。每一声部的声音 通过效果发送级导入到效果器中,通过系统效果器处 理过的声音信号 (“湿”音)将通过返送级输送至混 音台――与处理前的 “干”音进行混合。这样的安排 可以方便地调节原声和效果声之间的平衡。 混响效果器 混响效果器为原音渲染出温暖地气氛,模拟出多重反 射的真实演奏环境,例如音乐厅、小俱乐部等。总共 有 12 种不同的混响效果类型可选。 合唱效果器 合唱效果器采用调制手段产生出一个丰满的合唱声音 效果――好似几个乐器声部同时和该声部同时演奏一 样。总共有 25 个不同的合唱效果类型可选。 ■ 主控均衡器 通常均衡器用于修正听音场所的声学缺陷,均衡器将 声音按频谱分成多频段,然后对每一频段进行提升或 衰减,实现声学缺陷的修正。我们还可以依照音乐的 风格类型进行相应地调节―古典音乐的优雅、流行音 乐的明快、摇滚的动态―增添阁下演奏的乐趣。 S90 提供的是一台高级数字式五段均衡器。四个推子 用来调节 (五个频段中)四个频段的增益。 效果设置的样例
Basics Section 5 使用数字转盘选择 “FLG:FLANGER1 镶边” 之后,就可以演奏键盘了。如果需要调用其他 效果类型,可以在单独的数据表里查找。 阁下可以对已编辑过的音色和未编辑的音色进行试听 和比较。(见第 61 页) 如需采用旁通处理,请点按 [EFFECT BYPASS (效果 器旁通)] 按键 (其指示灯会变亮)。 Quick Guide 在效果参数显示屏中 ([SF2]-[SF5]),阁下可以获得 不同详细的参数设置。阁下可以通过 按键滚动屏幕。 有关效果参数的详细信息,可查阅数据表分册。 6 如果需要保存最新设置,在退出音色编辑模式 之前将该设置作为一个单独的音色进行储存。 有关储存音色的详细资料,可查阅第 73 页。 Reference 效果器连接 ● 在音色模式里: 如下图三个不同的嵌入式连接类型: Appendix 系统效果 混响 音频发生器 合唱 音色因子 1 嵌入式效果器 音色因子 2 音色因子 3 音色因子 4 发送级 返送级 1 主控均衡器 输出 2 阁下可以选中下图中的一种连接方案 指示每个音色因子选用哪一种嵌 入式系统
给 1 - 4 声部和 2 - 3 扩展声部 选用哪种嵌入式效果器。 Basics Section ● 在演奏音色模式里: 下图描述了当 S90 插槽 1 中安装了和声扩展卡 (PLG100-VH) 时,声音信号在系统内部的流向。 系统效果器 混响 合唱 变种 嵌入式效果器 发送级 返送级 1 声部 1-4, 扩展声部 2-3 主控均衡器 Quick Guide 音频发生器 输出 2 嵌入式效果器 Reference ( 扩展卡 ) PLG 100-VH A/D • 外部音源 • 话筒 和声扩展卡只能安装在插槽 1 上,不能安装在插槽 2 或插槽 3 上。 ● 在音序演奏及混合模式里: 如下图示,当插槽 1 已安装了和声扩展卡 (PLG100-VH) 并且插槽 1 已安装了多声部扩展卡 (PLG-100XG) 时,声音 信号在系统内部的流向。 系统效果器 音频发生器 混响 给每一声部选用哪种嵌入式效果 器。 合唱 声部 1~16 变种 嵌入式效果器 声部 17-32 * ( 当多声部扩展卡已被安装 ) 1 发送级 返送级 主控均衡器 输出 2 嵌入
Basics Section 运用工作 阁下可以在工作模式里演奏不同的工作。例如,阁下可以初始化音色或演奏音色至原始设置 (包括那些已被编辑 过的)或复制音色因子或声部。 工作 7 点按一个 MODE 按键(或 [EXIT] 按键)退出工作模 式,返回至演奏模式。 工作 Quick Guide 模式 初始化 调用 复制 批量复制 F1 F2 F3 F4 音色 是 是 是 是 演奏音色 是 是 是 是 主控 是 是 混合 ([SEQ PLAY] → [F6]) 是 是 演奏音色复制 出厂设置 设置模式 F6 - 重新设置 (初始化)音色 / 演奏音色参数返回至缺省 设置 [F1] 当阁下希望创建一个全新的音色或演奏音色时,该设 置可以为其建立一个 " 白板 "。注意该设置无法将演奏 音色返回至编辑前的原始状态。 是 第72页 Reference 选择参数类型并初始化 在液晶显示屏中的设置 演奏一个工作 对象 1 在每个模式里,请选择阁下所希望演奏工作上的音 色 / 演奏音色 / 主控号或混合。 Appendix 2 按 [J
通过以下显示屏,阁下可以将任一演奏音色中的公共 和声部参数设置复制到阁下希望编辑的演奏音色中 去。这对于阁下创建一个演奏音色并希望采用与其他 演奏音色一些相同的参数时非常有用。 演奏音色源 Quick Guide 使用复制功能 [F3] 音色 音色源 目标演奏音色 (当前选中的演奏音 色) 演奏音色源 选择一个演奏音色并且将其数据类型进行复制。 ❏ 数据类型 Reference 如下显示屏画面,阁下可以将任一音色的公共编辑以 及音色因子 / 鼓组音键参数设置复制到另一个您希望 编辑的音色中去。这对于阁下创建一个音色并希望采 用与其他音色一些相同的参数时非常有用。 声部 1 ~ 4, 扩展卡 1 ~ 3 目标演奏音色的数据类型 (当前选择的演奏音色) 设置目标演奏音色的声部。 ❏ 数据类型 目标音色 (当前选中的音 色) Basics Section 如果阁下编辑了一条音色或演奏音色或选择了一条还 未储存编辑的音色或演奏音色,那么阁下所有的编辑 将有可能被抹去。如果该不幸事情发生了,阁下可以 采用 Edit Recall (编辑召回)来完整无缺地恢复阁下 最后一次编辑的音色或演奏音色。
存储数据到外部设备 (批量存储) [F4] Basics Section 阁下可以通过批量存储把所有程序 (音色,演奏音色 和其它设置)的设置保存到阁下的电脑或其它 MIDI 设备。 要使用倾倒功能,必须设置一个可用的 MIDI 设备 号。(设置 [F5] → [SF1] 参考号 178)。 Quick Guide 当前的音色 / 演奏音色转为存储数据后,如果 阁下选择另一组音色 / 演奏音色或其它模式, 当前的数据将丢失。为避免丢失数据,阁下最 好使用存储功能把接收到的数据存储下来 (见 第 73 页)。 复制演奏音色的声部参数设置 [F5] Reference 这项便捷的操作可以让阁下把演奏音色中四个声部的 一些设置复制到当前正在编辑的混合程序中。这将让 阁下在应用混合程序时变得非常方便。通过这个操作 也简化了阁下需要的的设置复制工作。 MIDI 的接收通道设置设置成适应基本通道的设置。(设 置 [F5] → [SF1] 参考号 176)。 当基本通道设置为 “omn”后,接收通道设置为 1。 要复制一组参数,可以在显示屏复选相应的框。 出厂设置 (恢复到出厂时的默认值) 这可以使合成器恢复到
PROGRAM 更改名字,参考第 34 页。 SLOT 1 SLOT 2 SLOT 3 PRE 3 GM USER PLG 1 PLG 2 PLG 3 ORGAN GUITAR/ PLUCKED BASS STRINGS BRASS REED/PIPE Quick Guide S90 最多可以安装三个扩展卡。扩展卡正确安装 后,对应的插槽灯亮。 CATEGORY SEARCH 编辑后的混合数据可以通过 PUT 功能保存。 1 编辑完音色 / 混合音色后点按 [STORE] 按键。将出现 存储界面。 扩展音色可以通过 S90 的操作面板编辑,方法与 用户音色相同。编辑后,每个扩展卡最多可以保 存 64 种扩展音色。 ex.
3 保存存储器 (DRAM)中的数据到存储卡。 Basics Section 存储卡 3 扩展卡 MUSIC SYNTHESIZER Modular Synthesis Plug-in System Quick Guide S90 4 If necessary, set Auto Load to on in the Utility mode (page 84)。 设置为 “开” Reference 5 下次开机的时候,保存在存储卡中的自定义音 Appendix 色数据会被自动装载到扩展卡的存储器中。 74 保存设置
确保存有歌曲数据的存储卡已插到卡槽。 确保阅读了 " 储存卡的使用 " 一章(见第 82 页)。 S90 是同时兼容回放标准的 MIDI 文件或格式 0 的。如果需要的话,阁下可以将阁下电脑里的标 准的 MIDI 文件从格式 1 转换到格式 0。 在音序演奏模式下不要拔 / 插存储卡。 如果选择 “stop”,在放到这个阶梯链的时候会停止回 放。 ❏ 设置:跳过,结束,停止,歌曲文件,混合模板 阁下需要首先定义 (插卡模式)包含阁下要选择 的歌曲文件的目录。 Quick Guide 阁下可以直接回放保存在存储卡上的歌曲文件。通过 阶梯链最多可以按顺序回放 100 首歌曲。这个阶梯链 数据可以保存到存储卡 (见第 82 页)。 Basics Section 播放歌曲 1 点按 [SEQ PLAY] 键进入音序演奏模式。 2 用 [▲ ] 和 [▼] 键选择阶梯链号。 3 用[DEC/NO]和[INC/YES]键定义歌曲文件/混合模板 或跳过 // 结束 / 停止阶梯链。 Reference 同一个目录下的歌曲文件可以阶梯链回放。 设置链 4 重复上面第二步和第三步的操作设置阶梯链。 阶
Basics Section 歌曲音轨 开启 / 关闭 - 独奏和哑音 链式回放 1 用 [▲] 和 [▼] 键选择阁下想要回放的第一首歌曲 或者混合模板所在的阶梯链号。 哑音一个音轨 1 2 设置速度 (如果需要)。 2 3 4 5 6 7 8 12 13 14 15 16 ELEMENT / PERF.
● [F2] 音序演奏 输出通道 在这个模式下,阁下可以设置混合数据和针对音频发 生器声部 (包括期望的音频,还有深度,声相,均衡, 效果以及其它设置)的不同参数。 混合模式是怎样作用于音频发生器声部,以及其它音 色因子如何作用于混合模式,下面的图表会给出非常 清楚的说明。 音序模式 歌曲数据 OUT CH ( 输出通道 ) 代表到 MIDI OUT 端口的通道传输 (只能显示)。 端口 定义对应通道的 MIDI 传送端口。这对通过多个 MIDI 端口发送数据到外部音频发生器是很有用的。切记这 个参数只对定义了扩展声部 1-3 (安装了单声部扩展 卡)或扩展声部 17-32 (安装了多声部扩展卡)的通道 可用。 S90 的内部音频发生器声部自动配置到端口 1。 ❏ 设置 关闭 , 1 ~ 3 端口数据只能被输出到 USB 终端设备。 音频发生器块 来自于外部设备的 MIDI 数 据作用于混合设置。 混合 Reference 在音序演奏模式下,通过键盘和弯音轮产生的 MIDI 数据发送到音频发生器或者通过当前音轨 的 MIDI 输出通道输出到外部的 MIDI 设备。 歌曲回放数据作用于混合设置
3 用 [F6] 键选择一个阁下要混合的声部的显示窗口。 ● [F1] 音量 / 声相 Basics Section 阁下可以从下面的显示界面对每个声部的声相和音量 进行设置。 内置音频发生器声部 1~16 [F6] Quick Guide 多声部扩展卡声部 17~32 ( 当已经安装了多声部扩展卡 ) 在 [TRACK SELECT] 指示开启的情况下,阁下 可以通过移动光标或用 NUMBER 键选择声 部。 单声部扩展卡声部 1~3 (当已经安装了单声部扩展卡 ) [F6] 阁下也可以用控制推子调整音量 / 声相。细节 见第 53 页。 Reference 声相 定义每个声部的立体声声相。 音量 定义每个声部的音量。 [F6] 多声部扩展卡 (17~32) 的设置并不适用于单个 歌曲而是针对所有的模板。 Appendix 4 通过点按 [F1]-[F5] 选择阁下需要的编辑窗口,然后 在每个窗口下设置相应的参数。 ● [F2] AD 通过下面显示的窗口中,阁下可以为每个 A/D 声部设 置不同的混合参数,通过 A/DINPUT 插孔或 mLAN 接 线端口 (在可选配的 m
Basics Section 混合编辑模式 (详细的合成器功能) ● [F4] 发射 (效果发送) 从下面显示的界面,阁下可以对每个音轨进行基本设 置-混响,和声和不同的发送电平,还有干音电平。 公共编辑和声部编辑 Quick Guide 用公共编辑功能设置所有声部的共有的设置参 数。有两种混合参数显示方式:一种是公共编 辑,一种是单个声部的编辑。 声部 1 声部 2 声部 3 ● [F5] 模板 这个非常方便的功能可以让阁下将您的设置参数保存 为模板 - 允许您通过调用原有的模板建立相同的合成 器,然后调整到您所需要的。您也可以通过歌曲的回 放调用设置来为音序序演奏模式下的阶梯链分配模 板。模板是属于设置模式下的系统数据 (见第 27 页) 而不能被存为歌曲数据。 公共 声部 16 Reference 扩展声部 1 扩展声部 2 扩展声部 3 点 [SF4] 键调用左边选中 的模板 模板号 Appendix 通用编辑显示 声部编辑显示 模板名字 点 [SF5] 键保存当前的设 置 因为合成器模板是作为系统数据保存在闪存里 的,所以即使关电数据也不会丢失。 ( 见第 27 页)
4 选择要编辑的声部。 Basics Section 点按 [DRUM KITS] 键 (在这作为 "COMMON 键) 编辑所有声部的公共参数。 DRUM KITS FAVORITES COMMON Quick Guide 编辑单个声部的参数,阁下可以通过点按 NUMBER 键 ([1]-[16])选择您要编辑的声部。阁 下也可以用 [F6] 键选择扩展卡的声部 (如下图所 示)。 1 2 3 4 5 6 7 8 12 13 14 15 16 TRACK SELECT ELEMENT / PERF.
混合模式,然后进入编辑模式 (见第 29 页)。 7 用 和 键进入单音 / 复音设置。设置“Poly”(复音) 的参数。 Basics Section 1 点按 [SEQ PLAY] 键后,再点按 [F6](MIX)键进入 在进入混合模式之前,阁下需要先选择一个 要编辑的混合模板 (参见第 79 页)。 如果需要的话,阁下也可以初始话混合设置 (参见第 70 页)。 转换到声部编辑窗口。 这里,我们选择声部 1 为钢琴,声部 2 为贝司,声 部 10 为鼓。首先,我们先声部 1。 3 点按 [F1] → [SF1] 转换到 VOICE(音量)界面,然后 8 点按 [F1] → [SF3] 调用 NoteLimit (音符范围)和 VelLimit (力度范围)设置,并检查是否每个音频 的声部都已正确设置 - 换句话说,确保音符和速率 的设置都能正常的播放。除非在特殊的情况下,为 了确保音符听起来很正常并且没有间断,阁下通常 避免设置音符和速率的范围限制。 Reference 定义钢琴声部所需要的音频。 对于只有单音符的声部不可以设置成复音, 模式参数可以设成 “mono”(单音)。 Q
Basics Section 存储卡的使用 在存储卡模式下 , 阁下可以选择用存储卡 ( 商用的 SmartMedia 卡 ) 来存取数据 , 也可以执行其他的数据 处理操作。用嵌入式的应用软件 , 阁下可以在计算机 上用存储卡处理数据 , 也可实现计算机和存储卡之间 的数据交流。 ■ 存储卡的格式化 在使用存储卡之前应该先格式化存储卡。一旦被 格式化上面所有的数据将会被擦除。所以预先应 该检查数据是有用还是无用。 Quick Guide 在存储卡模式下请不要试图插拔存储卡。 用音序演奏模式播放阁下选择的音乐文件。在 存储卡模式下 , 指向了音乐回放的文件 ( 见第 83 页 )。 Reference 可处理的存储卡 (SmartMedia™*) 正确应用可处理的存储卡应注意下面重要信息。 * 东芝公司商标注册了 SmartMedia。 Appendix ■ 兼容存储卡类型 3.
1 点按[CARD]按键进入到插卡模式(该指示灯变亮)。 2 选择 [F1]-[F6] 菜单可执行 ( 保存。装载诸如此类的操 通过保存显示 ( 通过 [F2] 按键调用 ) 和重命名显示 ( 通 过 [F4] 按键调用 )。这项功能可使阁下在 S90 上方便 简单地创建大量自己的重要数据文件。 作 )。 Basics Section 新文件夹的创建 基本步骤 Quick Guide 3 点按任意模式按键退出插卡模式。 文件 / 文件夹选项 阁下可以通过点按 [F6] 按键来创建新文件 夹并且命名它。 下面的图文例子给阁下介绍了在存储卡的卡模式里是 怎样选择文件和文件夹的。 从 S90 可保存到存储卡的文件类型 点按 [EXIT] 按键 可返回到上层屏幕 的顶行。 加亮期望的文件夹 光标转到上层屏幕 的低行。 通过 [INC/YES] 和 [DEC/ON] 或者数字转盘把光标移动 到期望的文件或文件夹上。 显示 扩展名 解释 All .W4A S90 内置用户存储器的所有数据可作为一个单独的文件 存到存储卡里。 All Voice .
Basics Section ■ 开机时从存储卡加载到 S90 的文件类型 ( 自动加载文 件 )。 第 83 页描述的文件类型中 , “ALL”、“Plug-in All Bulk 1”、 “Plug-in All Bulk 2”、 “Plug-in All Bulk 3”可以在开机时自动从存储卡加载到 S90 的用户 存储器里。 数据将自动加载 , 存储器里存在的数据将会被覆 盖 , 因此阁下事先应该将重要的数据保存在存储 卡里。 Quick Guide 1 如下面描述 , 开了机时 , 命名阁下期望的已经自动上 载的文件。把它们放在同一个单独的文件夹内。 Reference 文件类型 文件名字 All AUTOLOAD.W4A Plugin All Bulk 1 (for slot 1) AUTOLD1.W2B Plugin All Bulk 2 (for slot 2) AUTOLD2.W2B Plugin All Bulk 3 (for slot 3) AUTOLD3.
[F3] 从存储卡往 S90 上载数据 本操作使阁下把文件保存到存储卡。这里将解释第 83 页基本步骤第二步的应用 本操作使阁下从存储卡里往 S90 里上载文件。 这里将解释 83 页基本步骤第 2 步的应用。 1 在保存显示里选择文件保存的类型 ( 见第 83 页 )。 1 择一个文件类型 ( 见第 83 页 ) 和一个文件上载。 Basics Section [F2] 保存 S90 里的数据到存储卡 如果阁下想要创建一个新的文件 , 可将光标移动到图 中所示位置 , 然后输入一个想要取的名字。详细的关 于命名资料 , 请查阅第 34 页关于 “基本操作”的章 节 当一个上载文件的类型为 “ALL”时 , “ without System” 信息将会出现在显示 屏上。如果这个框条被检查和上载被执行 , 设 置模式下系统设置除外的所数据将被上载。 Reference 如果阁下想要创建一个新的文件夹 , 请点 按 [SF6] 按键去命名一个新的文件夹。详 细的关于命名的资料 , 请查阅 34 页有关 “基本操作”的章节。 2 如果阁下想覆盖已存在的文件 , 移动光标或数字转盘 在保存数据
3 点按 [ENTER] 按键来执行上载操作。当数据已经被 Basics Section 上载 , 将会出现一个 “Completed” ( 完成 ) 信息。 操作返回原始显示屏。 在上载数据的过程当中, 请勿从S90中拔出存储 卡 , 也不要将 S90 关电。 S90 上载数据时将自动的擦除和覆盖用户存储 器里已经存在的数据。所以在执行上载操作之 前请确保将重要的数据保存在存储卡里。 [F5] 删除文件 在这个显示屏里,阁下可删除存储卡里选定的文件 , 选择要删掉的文件 ( 如下图所示 ), 然后点按 [ENTER] 按键。 选择期望的文件类型。 Quick Guide S90 有一个特色功能 : 方便的自动加载功能 , 当阁下开机时 ,S90 可自动加载用户指定的文 件。详细有关资料 , 请参考第 84 页。 选择要删掉的文件。 [F4] 重命名文件 Reference 在这个显示屏里,阁下可以给存储卡里选定的文件命 名 , 文件名最多可由 8 个字母和数字组成。 选择期望的文件类型 Appendix 选择重命名的文 件。 在这儿重命名选择的文件 , 详细资料请参考 34 页 ( “基本操
Basics Section 触发灵敏度 不同类型灵敏度的键盘可以匹配不同的演奏风格和参数选择。 1 点按 [UTILITY] (设置)按键进入设置模式。 3 使用 [ ] 按键选择力度曲线 , 再点按 [INC/YES] 和 [DEC/NO] 按键来选择期望的设置 ( 见下图 )。 4 点按 [EXIT] 按键退出设置模式。 音量 键盘演奏力度 柔和的 这个曲线提供增强性反映 , 尤 其对较低的力度。换句话说 柔和的演奏能反应出比常规 曲线强地音量。如果阁下在 弱音处想获得较强的控制效 果请使用该曲线。 强劲的 这个曲线比常规曲线能有效 的降低整体反映。如果阁下 注重演奏的强度又想降低音 量变化的灵敏度 , 请使用该曲 线。 音量 键盘演奏力度 音量 延伸的 这个设置提供和较低或较高 力度相应的反映曲线。能明 显延展动态控制音区。在弱 音处降低音量变化 , 在强音处 增加音量变化。 固定的 无论阁下的演奏力度如何 , 这 个设置提供等量的声音变化。 例如 , 阁下可用这个曲线模拟 传统音键或者验证声音的变 化一致性。 音量 键盘演奏力度 音量 Appendix 常规 力度和演
Basics Section 功能树 参考数字可以让阁下方便快捷地在参数表 (第 92 页)和参考章节 (第 98 页)中的相应参数进行交互参考。如需了解显 示屏的信息,请查阅第 33 页;如需了解搜索类别功能的信息,请查阅第 38 页;如需了解工作操作的信息,请查阅第 70 页;如需了解储存操作的信息,请查阅第 73 页;如需了解有关插卡的操作信息,请查阅第 82 页。 功能 子功能 参数名 ( 显示 ) 参考号 功能 子功能 页数 Quick Guide 参考号 页数 ElementSw 117 103 ■ 音色演奏模式 Source 118 [VOICE]→ 音色选择 ( 第 36 页 ) 设置 ...
98 主控均衡器偏 移 MEQ OFFSET (LOW/ LOWMID/HIGHMID/ HIGH) 6 其他 CSAssign 12 98 ChoCtrl 13 98 PB Upper 14 98 PB Lower 14 98 AssignA 15 98 AssignB 15 98 Assign1 15 98 Assign2 15 98 功能 子功能 [SF2] 力度灵敏度 43 [SF1] 电平/声相 [SF2] [SF3] 类型 限制 演奏 FX [SF2] [SF3] 设置1/2 设置3/4 设置5/6 连接 106 106 Level 135 103 Reverb Type 194 Pan 44 100 Chorus Type 194 106 AlternatePan 136 104 Reverb Send 195 106 137 104 Chorus Send 195 106 Level 151 104 Reverb Return 196 106 [SF3
Basics Section 功能 子功能 参数名 ( 显示 ) 参考号 页数 [SF3] 主控均衡器偏 移 MEQ OFFSET (LOW/ LOWMID/HIGHMID/ HIGH) 6 98 [SF4] 滑音 PortaSw 7 98 PortaTime 8 98 PartSwitch 9 98 CSAssign 12 98 ChoCtrl 13 98 AssignA 15 98 AssignB 15 98 Assign1 15 98 Assign2 15 98 [SF5] 其他 [SF2] [F2] (输出/主控均衡器) Quick Guide [SF1] [SF2] 输出 主控均衡器 Volume 43 100 Pan 44 100 RevSend 46 100 ChoSend 47 100 SHAPE/FREQ/GAIN/Q (LOW/LOWMID/HIGH/ HIGHMID/HIGH) 51 100 Reference [SF2] [SF3] [SF4] 类型 限
页数 参考号 页数 RevSend 46 100 Pan 89 101 ChoSend 47 100 Sus 89 101 VarSend 48 100 FS 89 101 DryLevel 52 100 (1ZONE/4ZONE) 89 101 [SF5] [F4] (重设) OutputSel 115 103 Bank MSB 132 103 InsEF 116 103 Bank LSB 132 103 PgmChange 133 103 NoteShift 41 99 Volume 43 100 Detune 153 104 Pan 44 100 Cutoff 92 102 Resonance 93 102 CtrlSlider 134 103 FEGDepth 154 104 100 [F4] (音高) [SF1] 调节 [SF2] 滤波器 [SF3] [SF4] [F5] (控制开关) 滤波包络发生器 Attack 155 105 ■ 设置模式
Basics Section 参数表 这个方便的表格可以使阁下快速且容易的找到期望的任 何参数―在 S90 的各种编辑模式点出它的位置并确认如 何调用。 Quick Guide 参数的设置将显示在选中的功能按钮 ([F1]-[F6])和子 功能按钮 ([SF1]-[SF5])中。下面的表格使在期望的模 式中调用各种参数变得特别容易。阁下也能够很容易的 看到那些在类似模式中的相关参数。 当您需要将音色模式下的参数拷贝到演奏模式下时,或 者您希望在演奏模式下做复杂细致的参数设置而不影响 音色模式的参数时,这个参数表显得尤为方便。 Reference 每一个参数都给出了所在页码和参数号码,在使用手册 中可以容易的找到相应解释。在使用 S90 时,每一个选 中的模式、编辑状态 (公共、单独等)和功能号码都有 简短注释,然后指向本表。 ■ 使用表格 • 参数按照相应功能按钮 ([F1]-[F6])组织和显示―在 Appendix 表中每一个以深色行标注。例如,阁下可以看到单音 / 复音参数 (F1 的第三个参数)属于 [F1] 按钮。同样 的,声相 (F2 的第二个参数)被第一次按下 [F2] 调 用。
... 能使用控制推子进行实时编辑。 ... 既能使用快速编辑功能进行编辑,又能使用控制推子进行实时编辑。 鼓组 扩展卡 常规 通用 F1 (标识名) 鼓组 主控编辑 UTILITY设置 扩展卡 振荡器 公共 声部 公共 声部 公共 音区 通用 音色 通用 音色 名字 传送 MainCtgry/SubCtgry SF1 SF1 SF1 SF1 Name SF1 SF1 SF1 SF1 Mono/Poly SF2 SF2 KeyAsgnMode/AssignMode SF2 SF2 M.TuningNo. SF2 MEQ OFFSET SF3 (PORTA) Switch (PORTA) Time SF3 音序演奏混合编辑 页数 1 98 通用 直接 SF2 号.
音色编辑 演奏音色编辑 Basics Section 公共 显示 常规 鼓组 音序演奏混合编辑 主控编辑 音色因子/音键 扩展卡 常规 鼓组 扩展卡 公共 声部 公共 声部 公共 (MLAN) Slider (F1→SF5) (F1→SF5) (F1→SF5) (F1→SF5) UTILITY设置 号.
扩展卡 常规 鼓组 UTILITY设置 扩展卡 公共 声部 公共 声部 公共 号.
音色编辑 Basics Section 显示 公共 常规 鼓组 演奏音色编辑 音序演奏混合编辑 主控编辑 音色因子/音键 扩展卡 常规 鼓组 扩展卡 公共 声部 公共 声部 公共 UTILITY设置 号.
B Bank..................................................... F1/F3 BankMSB/LSB........................................... F4 BankSel..................................................... F5 BasicRcvCh .............................................. F5 BC/AS1/AS2/FC1/FC2.......................... F3/F4 BCCurve ................................................... F1 BREAKPOINT (AMP)................................. F4 BREAKPOINT (FILER)............................... F3 C CenterKey (AEGTimeSens) ................
Reference Appendix *4 *6 53 87 56 87 87 67 84 给音色定义的调音系统 .
67 67 67 67 定义阁下点按一个音符后和音乐开始时这段时间的延迟。 定义哪个嵌入式效果 (1 或 2) 用来处理每个单独的音色因子 / 音键。“thru( 直通 )”的设置可使阁下旁通指定的音色因子 / 音键的嵌入式 效果 ( 这个参数和常规通用模式下的 " 音色因子 / 音键 : 输出 ([F6] → [SF1])" 相似。改动一个设置可自动使参数改变。 定义每个音色因子力度反应的下限和上限。 定义每个音色因子力度反应的下限和上限。 定义两个音色因子变换对力度响应的平滑性或陡然性 , 最小的取值将呈现两个音色因子之间产生陡然的变化 , 而最大的取值将呈现两个 音色因子之间产生平滑的变化。 定义是否一个声波或者常规音色用做选择的音键。 鼓音键编辑…当类型设 ( 上面提到的 ) 为 "voice( 音色 )" 时这个参数有用。某些常规音色库可被选。扩展音色不能被选。扩展音色因子 编辑…定义扩展卡音色库。演奏音色 / 固定声部编辑…定义每个声部的音色库 ( 见第 36 页 )。 定义是否音键释放信息被接收或不接收。 给阁下不希望 (客观上也无法)同时发声的鼓音符分配相同的号 ( 例如 - 开启镲
*28 *12 *29 45 45 45 定义半音程 (12 个音键:1 个八度音程 ) 音高的设置 (调整)。 定义音高的细调。 阁下演奏的每个音符的音色因子随机变化音高 ,数值为 127…则以最大的音高变化 ; 数值为 0…则没有音高变化。 定义一个程度 , 达到这个程度时力度影响音高包络发生器的音高变化。如果设置为正值音高变换将变的更加灵敏 , 这时演奏键盘感觉力度 较大 ( 较强劲 )。如果设置为负值将有相反的效果。 定义音高包络发生器电平 ( 音高包络发生器变化的度 ) 力度灵敏度。 定义从按下音键到发声结束之间的音高转变。 定义了音高跟随效果的灵敏度 ( 相临音符间隔 ), 设置为 +100 时临近音键之间为半音音程。设置为 0 时所有音键无音高差别 ( 在同一 音高上 , 适用于打击乐器等等 )。设置为 +50 时 24 个音键为一个八度音程。如果设置为负值 , 这些音键上的设置刚好相反 ( 音高顺序 颠倒 )。 定义音高音键跟随灵敏度参数 ( 上述 ) 的基本的音高 ( 音符号 )。该设置中的音符号与常规的音高相同 (100%)。 定义了音高包络发生器时间 ( 音高包络发生器变化的力度
64 63 64 65 65 当值设置为 "on( 开启 )" 时 , 琵音回放数据从 MIDI 端口输出。 为琵音回放数据定义 MIDI 发送通道。 KbdCH( 键盘通道 )…在设置模式 ( 演奏音色 / 混合音色 ) 下琵音回放数据通过 KBDTransCH( 键 盘发送通道 ) 发送。 给 BC( 呼吸控制器 )/Assign1 sliders( 可分配推子 1/2)/ foot controllers(FC1/2: 控制踏板 1/2) 设置控制号。 当相关参数设置为 "on( 开启 )" 时 , 弹奏选择的音区将发送相应的 MIDI 数据 , 例如控制变化和程序变化信息。点按 [F5] 按键将在所有四 音区和一个单音区 ( 在它里面有所有发送通道设置的显示 ) 之间切换显示。在四音区显示时 , 用光标来翻屏。 定义滤波类型 , 选择的类型不同参数设置不同。 定义滤波器输入声音信号的增益。 定义滤波器的截止频点或者滤波器应用的中心频点。 给截止频点定义谐振量。 通过带通滤波器 , 这个参数用来调节通过滤波器的信号频率宽度。 为双滤波类型定义两个截止频点的距离。 给高通滤波器的音键跟随参
55 定义滤波器的调整分界点 ( 滤波器截止频点随音符的位置的响应 ) 和偏移量电平。 定义低通滤波器的截止频点。 给截止频点定义滤波器谐振量。 定义低通滤波器截止频点力度灵敏度。 给单独的声部 ( 演奏音色 / 混合 声部编辑 ) 定义指定的输出。给单独的鼓组音键信号 ( 鼓组音键编辑 ) 定义指定的输出。 定义每个声部是否使用嵌入式效果。在这里只起到显示作用而不能被设置。 定义给每个单独音色因子是否选择控制器效果。 义哪个面板控制器是可分配的和用来做为选择设置。然后这个控制器可用来控制目标参数设置 ( 见下述 )。 定义被音源控制器控制的参数 ( 见上述 )。 定义一个度 , 达到这个度时音源控制器影响目标参数。 在滤波器截止频点上定义调制轮 ([SF2])/ 触后 ([SF3])/ 可分配控制器 ([SF4]) 的控制深度。 滤波器调整分界点 滤波器调整偏移量 低通滤波器截止 低通滤波器谐振 低通滤波器截止力度灵敏 度 输出选择 嵌入式效果 控制器设置 1-6 音色因子 开关 控制器设置 1-6 音色音源 控制器设置 1-6 目标 控制器设置 1-6 深度 调制轮 / 触后
定义控制变化号 ( 上述已设定的 ) 控制的控制号。参见数据表单独分册。 踏板控制器号 / 踏板功能分 用来给踏板分配一个指定的功能和控制号。 配 为阁独特的音序演奏软件选择模板。 通过指定的三个 MIDI 信息为每个音区选择音色。在数据表单独分册里参考音色表。 定义控制每个音区的推子的控制号。参数仅适用在当音区开关 ( 主控演奏模式 [F2]) 设置为 “on( 开启 )”和面板上的 "CONTORL FUNCTION( 控制功能 ) 设置为 “zone( 音区 )”时。 调节已选的音色因子 / 鼓组音键的输出电平 , 让阁下控制音色因子 / 音键的电平均衡。 定义一个量 , 通过这个量已选音色因子的声音声相将进行交替左右变化。声相参数可用做基本声相位置。 定义一个量 , 通过这个量已选音色因子的声音声相将进行随机左右变化。主声相设置用给基本声相位置。 定义一个度 , 到达这个度时已选音色因子的音符影响声相位置。在音符 C3 时 , 主声相设置用给基本声相位置。 定义一个度 , 到达这个度时力度影响振幅包络发生器。如果设置为正值,振幅包络发生器将变换得更加快速 , 这时演奏键盘感觉力度较 大
*57 *58 *59 定义不同声音的低频振荡器波形。用户…阁下编辑音色编辑时应用用户波形 ( 见安装操作指南单独分册 )。具体详细细节 , 请参见用户 手册的音色编辑部分 (PDF 文件 )。 定义低频振荡器波形速度 , 较高值对应较高的速度。 定义是否低频振荡器和琵音或音序 ( 歌曲 ) 同步。 允许阁下使用详细音符值设置来定义低频振荡器和琵音或音序怎样同步 ( 当速度同步参数设定为 “on( 开启 )” ( 见上述 )。 定义点按音键时低频振荡器是否重置。音色公共编辑模式时三个设置可用。 定义音键演奏时低频振荡器波形的起始相位点。 定义低频振荡器到效果器的延时。 定义为低频振荡器效果淡入 ( 延时完了后 ) 的时间量。较高的值产生较低的淡入时间。 定义低频振荡器保持在最大电平的时间长度。 定义为低频振荡器效果淡出 ( 延时结束之后 ) 的时间量。 定义是否每个音色因子受低频振荡器的影响。当受低频振荡器的影响时音色因子号 (1-4) 显示。 (-) 号说明音色因子不受 LFO( 低频振荡 器 ) 的影响。 定义受低频振荡器波形控制 ( 调制 ) 的参数。 定义低频振荡器波形的深度。 定义一个量 ( 深度
解释 67 67 67 67 69 69 定义哪个嵌入式效果 (1 或 2) 用来处理一个单独的音色因子 / “音键”。“thru( 直通 )”设置让阁下旁通为指定音色因子 / 音键用的嵌入 式效果。 ( 这个参数相当于常规音色因子 / 音键编辑模式 ([F1]→[SF2]) 的 “insEFOut” )。 定义嵌入式效果 1 和 2 的效果。设置的改变显示在屏幕里的图表中 , 给阁下一个直观的界面 ( 信号怎样传递 )。 为嵌入式 1 定义效果类型。参考数据表单独分册里的效果类型表。 定义混响器 / 合唱器效果类型。参考数据表单独分册里的效果类型表。 定义发送到混响 / 合唱效果的声音电平。设置为 “0”时声音没有混响。 定义混响 / 合唱效果的返送电平。 为混响 / 合唱效果定义声相位置设置 L64( 最左 ) ~ c( 中心 ) ~ R63( 最右 )。 定义信号从合唱效果器出来发送到混响效果器的发送电平。 定义嵌入式效果应用的声部。嵌入式连接类型取决于所选声部的音色。 定义嵌入式效果和嵌入式效果类型应用的声部。这个参数仅用在当一个指定的效果扩展卡 (VH) 已安装时。在 PLG-E
82 82 调节音频发生器旋钮 (100 :1 个半音程 )。 格式化存储卡。阁下可命名卷标。 设置作为一个文件保存到存储卡。 从存储卡上载文件到阁下的操作端。 可用最大八个字符命名文件名。 删掉保存在存储卡里的文件。 低频增益 高频增益 频率、频点 增益 均衡谐振 主控调节 格式化 / 卷标 保存 上载 重命名 删除 L.Freq/Gain (Type=EQ L/H) H.Freq/Gain (Type=EQ L/H) Freq (Type=P.EQ) Gain (Type=P.EQ) Q (Type=P.
Appendix Reference Quick Guide Basics Section
Francescatonio Vallotti and Thomas Young (17世纪中叶)发明这 个 , 调整使得六个中的前5个 音阶键相对常规低些。 一种均等调节的常规调音方 法,将音高上提音程的百分之 五十。 24音键一个8度音程,相邻两 个音键之间的音程为1/4音。 48音键一个8度程,相邻两个 音键之间的音程为1/8音。 通常在印第安音乐中较常见 (仅用[C-B]白色音键)。 A~G# 小调 Werckmeister Kirnberger Vallotti & Young 1/4 上移 1/4 音高 1/4 音高 印第安 13~24 25 26 27 28 29 30 31 C~B 该调节适用于大调式的音程 (特别是大三度和大五度)。 这就意味其它音程将会超出范 围。阁下需要指定C到B键。 C~B 大调 01~12 Johann Philipp Kirnberger 同样为 可以用任意键演奏考虑。 Andreas Werckmeiser, 当代的 BACH,设计这种方式可以演 奏的键盘每一音键,每一个键 代表一个特定的音符。 大调式相似
127 Received Velocity (Actual KeyOn speed) 64 Depth=0 Depth=32 (half) Depends on 64 offset Depends on offset Offset=0 (-127) Received Velocity (Actual KeyOn speed) 127 Offset=32 (-64) Offset=64 (normal) *21 这个参数对于扩展卡声部无效。 (混响效果器和合唱效果器)的发送级并不能 对每个鼔组键单独设置,设置值被设固定在 127 (最大值)。 *20 0 64 127 Actual Velocity for tone generator Offset=96 (+64) Offset=127 (+127) 力度偏移 依据力度偏移改变力度曲线 (将深度设置为 64) 0 64 Actual Velocity for tone generator Depth=127 (twice) Depth=64 127 (normal) 力度深度 依据力度深度改变力度曲
-40 +30 Basic pitch (center Key) Slower speed +63 Faster speed Higher range 阁下还可以通过面板上的 [ARPEGGIO ON/ OFF (琶音开 / 关) ] 按钮来控制琶音的开 / 关(在音色编辑中)。琶音开关在多扩展卡声 部 17 - 32 部分失效。 *30 当用户琶音被选择后,阁下可以通过 [SF5] 按 钮清除选中的琶音数据。 *29 Lower range Negative value Positive value 和方式和直通设置一样,指导中的音符也依 据琵音音序数据进行回放。 *33 指导 严格按照阁下演奏的指导来回放。如果改变 了音色参数 (例如音相或截止频点)包括在 琶音音序数据中,它们将实时进行变化。 直通 依照所按的音键回放音符。 方式 按照音键从最低往最高的顺序回放音符。 *32 非同步 当阁下第一次按一个键,最先的琶音模型音 符显示出来。从第二次和后来的按键,琶音音 符显示取决于琶音速率和琶音模型的安排时 间。例如,在 1 -阶琶音部分,如果第二次按 键三次敲击该键,
D#2 Break Point 2 C#1 Break Point 1 60 74 -4 偏置 Cutoff Frequency C#1 分界点 Break Point 3 C3 81 +10 D#2 2 Break Point 4 A4 68 +17 C3 3 Note +4 A4 4 90 -4 C1 84 +17 C3 3 Note +4 C4 4 任何低于分界点1的音符演奏时效果都为分界 点 1 的设置。同样的,任何高于分界点 4 的音 符都是分界点 4 的效果。 Appendix Reference 如需有关参数和控制的完整列表,可查阅数 据表分册。 *50 每一个可分配的推子 A 和 B 都可以被指定于 整个音色模式的一个相同功能,而不是某一 个独特音色的不同功能,同样可以参看设置 模式 ([F4]→ [SF2])。 *49 可分配的推子 1/2 不管这些偏移量设置为多少,截止 / 音量限制 的最大和最小值(分别为 0 到 127)不能被超 过。 呼吸控制器 AS1/2 Quick Guid
Time Time 实际音符长度取决于内部或外部 MIDI 速度 设置 (功能 [F5]→ [SF3]) 。 低频振荡器速度设置 16 分、8/3(8 分音符三连音 ) 、16 分音符 ( 带 附点 16 分音符 )、8 分音符三连音、8 分音符、 4 分音符、 2 分音符三连音、带附点的 4 分音 符。二分音符、全音符三连音、带附点的二分 音符、 4 分音符四连音、 4 分音符 5 连音、 4 分音符 6 连音、 4 分音符 7 连音、 4 分音符 8 连音。 *57 Speed = slow Speed = fast Key on (second note) Key on (first note) Key on (second note) Time 第一个开 (公共编辑) LFO 在弹奏每个音符时重置 LFO,以相位参 数 ( 下面 ) 指定的相位启动波形。然而,如果 您弹奏第二个音符,而第一个音符被按住, LFO 会根据由第一个音符击发的相同相位继 续循环。换句话说, LFO 只会在第一个音符 释放后,第二个音符弹奏时重新设置。 Key on (first note) Time
Local Off Keyboard MIDI IN MIDI OUT 音序器控制 关…不传送 / 不识别 输入…识别但不传送 输出…传送但不识别 输入 / 输出…传送 / 识别 *66 *65 在主控模式中,阁下可以选择是否对每一个 音区的 MIDI 进行传送信息。 Tone Generator MIDI OUT MIDI IN External MIDI Device 即使当本地控制设置为“OFF(关)”时,数 据仍然可以通过 MIDI 输出端后发送。同样, 音频发生器部分将通过 MIDI 输入端口接收的 信号作出响应。 *64 TG Local Sw KBD *68 TG Local Sw KBD Thru Port MIDI In MIDI Out From USB To USB MIDI In MIDI Out Low Gain - 0 + Gain Low Freq High Freq High Gain Frequency 均衡器 均衡器 L/H (高 / 低),扩展音色因子均衡 这是一个混合分离的高频和低频部分的抑制
Basics Section 附录 显示屏信息 Quick Guide 本信息显示屏让阁下一目了然的看到每个模式下相关 参数的重要设置信息。选择期望的模式 , 然后点按 [INFORMATION] 按键来调用此模式的显示屏信息。想 要退出显示屏信息 , 请再次点按 [INFORMATION] 按键 ( 或者其它的面板按键 )。 演奏音色 音色模式 Bank (音库) Reference 显示当前已选择演奏音色的音库 (MSB/LSB)。 Bank (音库) 显示当前已选择音色的音库 (MSB/LSB)。 Appendix EL (音色因子) 1234 显示当前已选择音色的的四个音色因子和单音 / 复音状 态为开启 / 关闭。 (Porta)滑音 显示当前已选择音色的的滑音为开启 / 关闭状态。 1 (扩展卡 1) ,2 (扩展卡 2) ,3 (扩展卡 3) 显示已安装扩展卡各自的状态。扩展卡名显示在相应 插槽号的右侧。当在设置模式设置复音扩展 ( 参考号 206) 为开启时 ,"P" 显示在插槽号的左侧。 InsPart (嵌入式声部), PLG (Plug-in 扩展卡嵌入式声 部)
InsPart (嵌入式声部), PLG(Plug-in 扩展卡嵌入式声 部) 显示嵌入式效果器应用的声部号和扩展卡嵌入式效果 器应用的声部号。 ( 当 PLG100-VH 安装时 )。 Rev (混响) , Cho (合唱) ,Var (变种) 显示每个效果器当前所选的效果类型 ( 见第 67 页 )。 Volume Label (卷标) 显示存储卡的卷标。 Current Dir (当前目录) 显示当前已选的目录 ( 见第 83 页 )。 主控模式 Appendix 设置模式 Card Free (存储卡空余空间) 显示存储卡当前可使用的内存空间 ( 空余的内存空间 )。 Reference PlugInfo/Port (扩展卡安装状态) 在槽位号的右侧显示扩展卡的名字和它的 MIDI 端口号 ( 参考号 207, 见第 77 页 )。当在设置模式设置复音扩展 ( 参考号 206) 为开启时 , “P”显示在插槽号的左侧。 Quick Guide Basics Section 插卡模式 PlugInfo/Port (扩展卡安装状态) 在槽位号的右侧显示扩展卡的名字和它的 MIDI 端
Basics Section 屏幕显示的信息 屏幕显示的信息 屏幕显示的信息解释 Quick Guide Reference Appendix Are you sure? [YES]/[NO] 需要阁下点按 [INC/YES] 或者 [DEC/NO] 按键来确认是否执行或不执行指定的的操作。 Bad Card. 卡不可用 , 请先格式化卡再重试。 Bulk protected. 当 RcvBulk( 批量接收 ) 被设置为“Protect”( 保护 ) 时能接收到批量数据 ( 设置 [F5] → [SF2] 参考号 184)。 Can’t make folder. 当前等级下 , 无法建立目录。 Card full. 卡已经存满数据。请使用一张新卡或者从卡上删掉一些没用的数据腾出空间。 Card not ready. 卡没有插好或者和 S90 没有连接好。 Card read/write error. 读 / 写存储卡时出错。 Card unformatted. 卡没有被格式化 , 或者不符合 S90 格式。请检查卡的内容。 Card write protected.
Basics Section 屏幕显示的信息解释 安装在插槽 3 上的扩展卡不能工作。 Plug-in 1 type mismatch. 插槽 1 上安装的扩展卡不匹配 , 不能产生用户音色。 Plug-in 2 type mismatch. 插槽 2 上安装的扩展卡不匹配 , 不能产生用户音色。 Plug-in 3 type mismatch. 插槽 3 上安装的扩展卡不匹配 , 不能产生用户音色。 Read only file. 只读文件 , 不能做以下操作 : 删除,重命名或者覆盖。 Receiving MIDI bulk. S90 接收到 MIDI 批处理文件。 System memory crashed. 因为设备执行操作的过程当中 , 进行了关电操作 ( 这时用户数据已经完成了自动初始化 )。这样给闪存写 数据时提示出错信息。关掉电源重新加电尝试。 This Performance uses User Voices. 阁下执行的上载操作包含用户音色数据的提示。请检查阁下是否将音色保存在正确的用户音色库里。 Too many favorites.
Basics Section 关于 MIDI MIDI 是 Musical Instrument Digital Interface 的缩写,即 “数字音乐设备接口”。它通过发送或接受音符、控制变 量、程序变量以及不同类型的 MIDI 数据和信息,实现不同的音乐设备相互沟通和联系。 S90 通过传送音符的相关数据和不同类型的控制数据来控制 MIDI 设备,同时接收的 MIDI 信息对 S90 也进行相应 的控制,它自动决定音频发生器的模式,选择 MIDI 信道、音色、效果,改变参数量,当然还可以播放不同部分的 音乐。 Quick Guide 许多 MIDI 信息由十六进制或二进制数码表示,十六 进制数码用字母 H 做后缀,字母 n 表示某一个整数。 Reference Appendix Decimal Hexadecimal 0 00 1 01 2 02 3 03 4 04 5 05 6 06 7 07 8 08 9 09 10 0A 11 0B 12 0C 13 0D 14 0E 15 0F 16 10 17 11 18 12 19 13 20 14 21 15 22 16 23 17 24 18
S90 是一部完全的复音音频发生器,它能够根据 S90 分 配不同的 MIDI 信道给不同的声部同时发出不同乐器部 分的声音。 S90MIDI 信息的发射与接收 MIDI 信息可以分为两个部分,即信道信息和系统信 息。以下介绍的使 S90 能够接受和发送的不同类型的 MIDI 信息。 注:音序器只传送已经记录歌曲的全部控制变量信息。 信道信息 信道信息是用于在与键盘上演奏有关的数据。 ■ 触发与关闭 弹奏键盘是产生的信号。 接受音符的范围= C-2(0)-G8(127),C3=60 力度范围= 1 - 127 (仅在接受到触发力度时) 触发:按键在被按下时产生 释放:按键在被释放时产生 每种信息包括在按下按键时与之相应的特殊音符, 加上基于敲击按键力量大小产生的力度值。 ■ 控制变化 控制变化信息让阁下选择一个音色库、控制音量、 声像、颤音、滑音时间、明亮度以及其他的控制参 数。 音库选择 MSB (控制号 000) 音库选择 LSB (控制号 032) 从一个外接设备中,通过组合和发送 MSB 和 LSB 信号,从而选择变化音色库的信息。根据不同的音 源模式, MSB 和 LSB 的功能会不一样。 MS
持续 (Control 号 066: 控制号 066) Basics Section 控制持续的开启 / 关闭状态信息。 当阁下演奏持续音符时 , 按住指定的音键然后点按和按住 持续踏板可持续音符 , 直到持续踏板被释放。 数值设置为 64 ― 127 持续为开启状态 , 数值设置为 0-63 持续为关闭状态。 和声丰满度 (Control 号 071: 控制号 071) Quick Guide 为每个声部调节滤器波谐振的信息。 在这里此值为一个偏移量 , 用来给音色数据补偿或者减除 一个值。 值很高的话有一个特性 : 谐振声音 根据音色特点 , 有效的音域范围可能比调整的音域范围 窄。 释放时间 (Control 号 072: 控制号 072) Reference 为每个声部调节均衡释放时间的信息。 在这里此值为一个偏移量 , 用来给音色数据补偿或者减除 一个值。 触发时间 (Control 号 073: 控制号 073) 为每个声部调节均衡触发时间的信息。在这里此值为一 个偏移量 , 用来给音色数据补偿或者减除一个值。 明亮度 (Control 号 074: 控制号 074) Appendi
参数 RPN MSB RPN LSB 00 00 弯音灵敏度 00 01 细调 00 02 粗调 7F 7F 零 0 所有声音关掉 121 0 重设所用控制 123 0 所有音键关掉 126 0 ~ 16 单通道模式 127 0 多通道模式 Basics Section 第三字节 120 信息 所有声音关掉 (Control 号 120: 控制号 120) 关掉当前选中的发声通道的所有声音。然而 , 通道的音 键按启和保持按启状态还能保持。 Quick Guide 第二字节 重设所有控制 (Control 号 121: 控制号 121) 下面控制器的值将会重设为默认值 控制器 弯音轮变量 数值 0( 中心值 ) 触后(键) 0 (关闭) 多通道触后(键) 0 (关闭) 调制 0 (关闭) 表达 127 (最大值) 保持1 0 (关闭) 滑音 0 (关闭) 持续 0 (关闭) 软持续音 0 (关闭) 滑音控制 取消滑音来源音键的值 RPN(注册参数码) 数值没有选中,内部数据不变 NRPN(非注册
Basics Section ■ 程式变化 哪个音色挑选给每个声部的决定信息。在组合选择 音库里 , 阁下不仅可选择基本音色号码 , 而且可选 择变种音色号码。 ■ 弯音轮 当控制信息允许选中的音符音高在指定时期按照特 定数量上移或者下移 , 弯音轮信息将持续控制。 Quick Guide ■ 触后通道 在整个通道上 , 当初次按键后可根据阁下在按键上 按压的力度来控制声音的信息。 ■ 多通道模式的触后 在每个按键上 , 当初次按键后可根据阁下在按键上 按压的力度来控制声音的信息。 S90 不能从键盘上发送此数据 , 然而 , 该数据可从 S90 的内置音序器发送。 系统信息 系统信息是和设备整个系统都相关的数据。 ■ 系统独有信息 系统独有信息控制 S90 不同的功能 , 包括主控音 量,主控调谐,音频发生器模式,效果器等其他参 数。 通用 MIDI 系统开启 ( 仅限音序演奏模式 ) 当收到 “General MIDI system on”信息时 ,S90 将从 MIDI 收到和 GM 系统第一层相兼容的信息 , 但不能接收 到 NRPN( 非注册参数码 ) 和库选择信息。 F0 7E 7F 0
mLAN8E 安装位置 mLAN8E 盖板 扩展卡盖板 最多有三块扩展卡可以被安装在背板中。 • 开始安装前 , 先关掉 S90 的电源和外置设备连接 , 拔掉它 们的电源插头。然后移开 S90 和其他设备的连线 ( 如 果不移开电源线缆可能导致工作时遭到电击。其他连 线不移开可能会产生干扰 )。 • 安装时小心不要使螺丝掉到设备里面 ( 通过把可选配扩 展卡和盖板从移开设备可减少事故的发生 )。但是如果 发生了螺丝掉进设备里 , 在加电之前一定要掏出螺丝。 掉在设备里的螺丝会导致设备不能正常工作或者设备 毁坏。如果阁下不能找回掉进设备的螺丝 , 可请求 Yamaha 专业人员帮助。 • 安装可选配扩展卡应该遵从说明书的步骤。不当的安 装可能引起短路烧毁设备或者引起火灾。 • 请勿拆卸,改动或者强力挤压设备面板或者可选配扩 展卡的连接头。弯曲,挤压设备面板或者连接头会导 致漏电,失火或者设备毁坏。 • 在安装可选配扩展卡前 , 阁下应该将手和插可选配扩展 卡的设备外壳接触 ( 或者和其他金属部件接触 - 小心划 伤 ), 这样可以去掉身体所带的静电。注意甚至少量的 静电也会引起设备组件的毁坏。 •
Basics Section 可选配扩展卡的安装 A各种可选配扩展卡(见第21页)的销售可使阁下扩展自 己的乐器音色。 下列是可用于阁下设备的扩展卡类型 : Quick Guide • PLG150-AN • PLG150-PF • PLG150-VL • PLG150-DX • PLG150-DR • PLG150-PC • PLG100-XG • PLG100-VH 3 断开 S90 内部用来固定扩展卡的缎带橡胶线 , 插槽用 三种不同色线进行了区别 : 插槽 1 — 橙色 插槽 2 — 黄色 插槽 3 — 绿色 Plug-in SLOT 3 2 1 插槽 3 的 连线 ( 绿 色) GREEN YELLOW ORANGE 插槽 3 插槽 2 插槽 1 插槽 2 的连 线 ( 黄色 ) 绿色 黄色 橙色 扩展卡的安装 Reference S90的后面板有三个插槽,允许安装三个不同的扩展卡。 1 关掉S90的电源,拨下交流电线。并且断开S90和其他 外置设备的连线。 4 接头面对阁下 , 按着指标插入扩展卡。 和声声部扩展卡 (PLG100-VH) 插在插槽 1 内。 多声
6 将第二步拆下的螺丝和盖板装回去 , 确保盖板螺丝孔 对准。 6 检查扩展卡 , 确保插好后可加电。 • 一条扩展卡安装检测的信息将会显示 , 主屏幕将会 Plug-in SLOT 3 2 1 GREEN YELLOW ORANGE 出现 , 面板右上边有指示灯提示扩展卡已被成功安 装。 Basics Section 5 将扩展卡插入槽内 , 慢慢往里推直到和接口吻合。 装成功。出现这种情况 , 请关掉电源重新按安装指 导手册安装。 指示灯 PROGRAM 6 将信号线接到扩展卡上 , 确保色线和插槽的对应关 系。连接扩展卡时请勿太用力 , 以免线缆损伤。 SLOT 1 SLOT 2 SLOT 3 PRE 3 GM USER PLG 1 PLG 2 PLG 3 ORGAN GUITAR/ PLUCKED BASS STRINGS BRASS REED/PIPE Quick Guide • 如果出现出错信息 ,S90 会死机 , 表明扩展卡没有安 CATEGORY SEARCH 样例中一个扩展卡安装在了槽位 1。 Reference 按压两个接口使槽
Basics Section 可选配 mLAN8E 卡的安装 通过 mLAN8E 接口卡可以方便的把其他和 mLAN 兼 容的部件或设备和 S90 相连。 4 阁下用左手从里面托住 S90, 拆下后面板的三个螺 丝。 mLAN8E 的安装 1 关掉S90的电源,拔掉交流线。并且断开S90和其他外 Quick Guide 置设备的连线。 2 把 S90 翻转过来 , 阁下能看到设备背面。为了保护旋 钮。弯音轮在四个脚上应该放置胶皮,软垫之类的 东西来支垫。 放好拆下的螺丝 , 以便将来拆下 mLAN8E 时再 装好 S90 的盖板会用到这些螺丝钉。 Reference 5 从包装盒内拿出 mLAN8E, 连接好内部的扁平缎带数 据线。安全牢固的将扁平缎带数据线连在 mLAN8E 后面板。确保缎带线在上部 , 如图所示 : 背面视图 mLAN8E 上部 MUSIC SYNTHESIZER Modular Synthesis Plug-in System Appendix 请在四个脚上垫上东西防止弯音轮的挤 压。 请保证设备稳固平衡 , 以免设备摔落或碰 撞。 确保缎带线在接头上部。
拆下的螺丝上紧部件。如果从中间螺孔开始上螺丝 钉能容易上好螺丝钉。 8 将mLAN8E颠倒,将扁平缎带数据线的另外一端接口 插进 S90 的电路插槽。 Basics Section 6 将 mLAN8E 固定在第 3 步拆下的内罩里。用第 4 步 针式接口如图所示。 1 2 Quick Guide 3 S90 侧面 7 用 mLAN8E 自带的扎带固定好 mLAN8E 顶部出来的 S90 后面板 mLAN8E 侧面 Reference 缎带数据线。 6 重新装好 S90 的盖板 ( 安装了 mLAN8E 后的 )。 将此插进 S90 内部。 可选配硬件的安装 127 Appendix mLAN8E 正面
Basics Section 故障解决 没有声音 ? 声音不正常 ? 当这些问题产生时 , 排除产品不完善问题 , 先参见下面的可能出现问题点。通 常情况 , 阁下可在这里找到问题解决方法。如果问题依然存在 , 请联系阁下的雅马哈经销商或服务中 心 (见第 138 页)。 Quick Guide 没有声音 .
Basics Section 声音电平太低 ● 是否将 MIDI 音量或 MIDI 表达设置太低 ( 用控制踏板设置 )?( 见第 18 页 ) ● 是否将滤波截止频率设置太高 / 太低? ( 参考号 92,96) 声音截止 音高或者间隔出错 ● ● ● ● ● ● 是否将设置模式的主控调音参数设置为 “0”以外的值 ?( 参考号 216) 是否将设置模式的的音符转换参数设置为 “0”以外的值 ?( 参考号 41) 当音色产生一个错误的音高 , 是否将在音色编辑模式下的微调节系统参数正确设置 ? ( 参考号 5) 当音色产生一个错误的音高 , 是否将在音色编辑模式下低频振荡器音高调制深度设置太高 ? ( 参考号 172) 当演奏音色产生一个错误的音高 , 是否将每个声部的音符转换参数设置为 “0”以外的值 ? ( 参考号 41) 当演奏音色产生一个错误的音高 , 是否将每个声部的的误调参数设置为 “0”以外的值 ? ( 参考号 153) Reference Quick Guide ● 是否超过了 S90 的最大复音 ( 见第 22 页 ) 每次只有一个音符发声 Appendix ● 是否将音
不能将数据保存到存储卡里 Basics Section ● 存储卡是否有写入保护 ( 保存数据时应该打开写保护 )?( 见第 82 页 ) ● 用到的存储卡是否正确格式化过 ? ( 见第 82 页 ) MIDI 批量数据发送 / 接收不正常 ● 是否将设置模式下的接收批处理参数设置为 “protect( 保护 )” ?( 参考号 184) Quick Guide 扩展卡不工作 ● 对应的插槽指示灯是否亮 ?( 见第 73 页和 125 页 ) ● 和声声部是否插在了 2,3 槽位 ?( 和声声部部扩展卡应该安装在槽位 1 里 )( 见第 124 页 ) ● 多声部扩展卡安装在了 1,2 槽位 ?( 多声部扩展卡应该安装在 3 槽位 ) ( 见第 124 页 ) Reference 开机时 S90 因为故障或不正确操作引起挂起或者死机 ● 正在给闪存写数据时 , 当有 (“Executing…”( 正在处理中 ) 或“Please keep power on”( 请保持开机状态 )) 的信息显示 , 请 勿试图关机。如果在此状态进行了关机操作 , 将引起用户数据的丢失 , 还可能引起死机。如果发生了此
键盘 音序器 其他 88 键,平衡击弦效果 ( 初始力度和触后感应 ) AWM2 声音引擎 ( 与模块化合成扩展系统结合 ) 复音 64 复音,可以通过模块化合成扩展系统扩展卡扩展 ( 如果安装 ) 配置 16 声部 (内置)+ 3 或更多插卡声部 (1 为单插卡声部 ,16 为多插卡声部 ), A/D 输入 声波 110MB 波形存储 (16-bit 线性格式), 1347 波形 音色 预置音色 :384 常规音色+ 48 套鼓组 GM : 128 常规音色 + 1 套鼓组 User( 用户 ): 128 常规音色 + 16 套鼓组 扩展音色 预置 PLG150-AN/PF/DX/DR/PC:64 预置 PLG-150VL: 192 用户 : 每个扩展卡 64 演奏音色 用户 :128( 等于 4 个声部 ) 琶音器 预置 1 x 128 类 预置 2 x 128 类 用户 128 类 ( 只读 ) * MIDI 同步, MIDI 发送 / 接收通道,力度限制和音色限制可设置 滤波器 21 类 效果器 12 类混响, 25 类合唱 , 25 类嵌入式 1, 104
Basics Section 索引 A Quick Guide Reference Appendix A/D (Performance Play) 数 / 模 (演奏音色弹奏模式)............. 44 A/D input (Connections) 数 / 模输入 (连接)............................ 15 A/D INPUT jack 数 / 模输入插孔................................................. 13 A/D Source 数 / 模输入 (音源)............................................... 100 Absolute 绝对的.............................................................................
G GAIN 增益 ............................................................................. 15, 100 Gain 增益 ..................................................................... 100, 102, 107 [GAIN] knob 增益旋钮 ................................................................. 13 GateTimeRate (琵音)门限时间比率...................................... 101 GENERAL (Voice Common) 通用 (音色公共设置)............... 62 General MIDI (GM) System On 通用 MIDI (全球标准)系统 122 GM System 全球标准系统......................................................
Basics Section Quick Guide 13 mLAN Settings mLAN8E 设置 ................................................ 100 mLAN8E (Install) mLAN8E 安装 . .......................................... 126 mLAN-compatible audio equipment 兼容 mLAN8E 的音频设备 ........................................................................................................ 15 Mode 模式...................................................................................... 98 MODE buttons 模式按键..........................................................
TEMPLATE (Mixing) 模式 (混合)........................................... 79 Tempo 速度,拍子...................................................................... 101 Tempo (Arpeggio) 速度 (琵音)................................................. 46 TempoSpeed 拍子速度 ................................................................ 105 TempoSync 速度 (拍子)同步................................................. 105 TGSwitch 音频发生器开关........................................................... 99 Thru Port 直通端口..........................
备忘录 136
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen Bestimmungsländern erhältlich. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante.