User Manual
Table Of Contents
- Welcome
- Accessories
- About the accessory disk
- S90 XS/S70 XS Main Features
- About this Manual
- Contents
- Controls and Functions
- Setting Up
- Start Guide
- Modes
- Basic Instructions
- Playing the Keyboard in the Voice mode
- Creating a New Performance by Using Your Favorite Voice (Performance Creator)
- Playing the Keyboard in the Performance Mode
- Singing with a Connected Microphone
- Recording/Playing Back with a USB Storage Device (Audio Record/Play Mode)
- Using a Connected Computer
- Playing the Keyboard Along with Playback of the MIDI File
- Using as a Master Keyboard (Master Mode)
- Making Global System Settings (Utility Mode)
- Saving/Loading Data (File Mode)
- Appendix
- Display Messages
- Troubleshooting
- No Sound
- No sound from the MIC INPUT jack
- Split does not work via the external MIDI device
- Playback continues without stopping
- The sound is distorted
- Sound is cut off
- Only one note sounds at a time
- Wrong pitch or unexpected pitch
- No effect is applied
- Vocoder does not work when selecting a Vocoder Voice
- The Edit Indicator appears, even when parameters are not being edited
- Cannot start the Arpeggio
- Cannot stop the Arpeggio
- The Voice assigned to the Performance produces a different sound from the one in the Voice mode
- Data communication between the computer and the S90 XS/S70 XS does not work properly
- The S90 XS/S70 XS does not sound properly even when playing back the song data on the computer or the MIDI instrument connected to the S90 XS/S70 XS
- MIDI bulk data transmission/reception does not work properly
- Cannot save data to the external USB storage device
- Cannot play an audio file
- Cannot enter the Edit mode
- Specifications
- Index
S90 XS/S70 XS Owner’s Manual
51
Display Messages
Load All. Are you sure?
Confirms whether you want to load the “All” or not in the File mode.
Load Seq Chain file. Are you sure?
Confirms whether you want to load the “Seq Chain file” or not in the File mode.
MIDI buffer full.
Failed to process the MIDI data because too much data was received at one time.
MIDI checksum error.
An error occurred when receiving bulk data.
Mixing Voice full.
The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the
maximum capacity.
No read/write authority to the file.
No permission for reading/writing on the external storage device.
Now executing Factory set...
Please keep power on.
Indicates this synthesizer is restoring the factory-programmed settings.
Now loading...
Indicates that a file is being loaded.
Now receiving MIDI bulk data...
Indicates this synthesizer is receiving MIDI bulk data.
Now saving...
Indicates that a file is being saved.
Now scanning autoload file...
Scanning for the files specified for Auto Load.
Now transmitting MIDI bulk data...
Indicates this synthesizer is transmitting MIDI bulk data.
Overwrite. Are you sure?
A save operation will overwrite data on the external storage device as destination, and this message
confirms whether it is OK to continue or not. Press [ENTER] (Yes) or [EXIT] (No) as required.
Part x is used for Drum Assign.
This message appears when the Part switches of all Parts are set to on, and the Drum Assign function
used Part “x” for the Drum Part in Performance mode.
Part x is used for Layer.
This message appears when the Part switches of all Parts are set to on, and the Layer function used
Part “x” for the Layer Part in the Performance mode.
Part x is used for Split.
This message appears when the Part switches of all Parts are set to on, and the Split function used
Part “x” for the Split Part in the Performance mode.
Please stop Audio Play/Rec.
The operation you have attempted to execute cannot be done during Audio Rec/Play recording or
playback.
Please stop sequencer.
The operation you have attempted to execute cannot be done during SEQ PLAY playback.
Save Audio Rec file?
Confirming whether you want to save the recorded file or not in Audio Rec/Play mode.
Seq Chain stored.
This message appears when the Seq Chain settings has been stored.
Sequence memory full.
The internal memory for Sequence data is full, preventing any further operation (such as recording,
editing, Job execution, MIDI reception/transmission, or loading from the external storage device).
Try again after erasing unwanted Song, Pattern, or User Phrase data.
Set Part 1 Ins Sw to on to use Vocoder.
Set the Insertion Switch of Part 1 to on to use the Vocoder when setting the Output Select of the A/D
Input part to “Vocoder.”
MIDI data overload.
The amount of MIDI data is too large to play.
Store Voice?
Confirms you want to store the editing Voice when executing the Performance Creator (Layer/Split/
Drum Assign) feature to the editing Voice in the Voice mode.
The received MIDI bulk data’s type is not
compatible with the current mode/voice
type.
This message appears when MIDI bulk data is received in a different mode other than the currently
selected mode. The bulk data is received in the same mode as the transmitting mode. This message
also appears when the Voice type (Normal Voice/Drum Voice) of the destination Mixing Parts is
different from the bulk-dump-transferred Voice type. The destination Parts assigned to the same Voice
type as the bulk-dump-transferred Voice type are selected.
This Performance uses User Voices.
The loaded Performance uses User Voices. Confirm whether the same Voices as at the time of saving
are stored at the same User Bank/Number or not.
USB connection terminated.
Press any button.
A break in the connection with the USB storage device has occurred because of an abnormal electric
current. Disconnect the USB storage device from the USB TO DEVICE connector, then press any of
the panel buttons.
Utility stored.
The settings in the Utility mode have been stored.
LCD Indication Description