User Manual

Reference Manual
Reference
51
Voice
Performance
Multi
SEQ Play
Master
Remote
File
Audio Rec/Play
Utility
Voice
Play
Normal Voice Edit
Common Edit
Name
Play Mode
Arpeggio
Arp Edit
Arp 1-5 Type
Controller
LFO
Filter/EG
3 Band EQ
Effect
Element Edit
OSC
Tune
PEG
Filter Type
FEG
Filter Scale
AMP Level/Pan
AEG
AMP Scale
LFO
EQ
Drum Voice Edit
Common Edit
Name
Play Mode
Arpeggio
Controller
Filter/EG
3 Band EQ
Effect
Key Edit
OSC
Tune
Filter Type
AMP Level/Pan
AEG
EQ
Job
Recall
Bulk
Supplementary Info.
Basic Structure
Appendix
Cutoff Key Follow (Cutoff Key Follow Sensitivity)
Determines the degree to which the notes (specifically, their
position or octave range) affect the “Cutoff” (set above) of the
selected Element, assuming C3 as the basic pitch. A positive
setting will lower the Cutoff frequency for lower notes and
raise it for higher notes. A negative setting will have the
opposite effect.
Settings: -200% – +0% – +200%
HPF Cutoff (High Pass Filter Cutoff Frequency)
Determines the central frequency for the Key Follow
parameter (below) of the HPF. This parameter is available
only when filter types LPF12 or LPF6 are selected.
Settings: 0 – 255
HPF Key Follow (High Pass Filter Cutoff Key Follow Sensitivity)
Determines the degree to which the notes (specifically, their position or octave range) affect the “Cutoff” (set above) of
the HPF. A positive setting will lower the Cutoff frequency for lower notes and raise it for higher notes. A negative setting
will have the opposite effect. A setting of 0 will result in no change in the note. This parameter is available only when
filter types LPF12 or LPF6 are selected.
Settings: -200% – +0% – +200%
Time
Determines the Filter EG transition time. The Time parameters let you set the time between the adjoining points of the
level parameters below. When the current Level setting is the same as the next, the corresponding Time indicates the
length of time for which the Level is held at the current setting. A higher value results in a longer time until reaching the
next level.
Settings: 0 – 127
Level
Determines the Filter EG transition time. The Level parameters let you set the amount of the filter change at each point
based on the cutoff frequency specified in the Filter Type display (page 50).
Settings: -128 – +0 – +127
FEG (Filter EG)
Hold Time Determines the time between the moment you press a note on the
keyboard and the moment the envelope starts to rise.
Attack Time Determines the speed of attack from the initial cutoff frequency (Hold
Level) to the maximum level (Attack Level) of the Voice after the hold
time has elapsed.
Decay 1 Time Determines how fast the envelope falls from the maximum cutoff
frequency (Attack Level) to the cutoff frequency specified as the
Decay 1 Level.
Decay 2 Time Determines how fast the envelope falls from the cutoff frequency
specified as the Decay 1 Level to the cutoff frequency specified as
the Decay 2 Level.
Release Time Determines how fast the envelope falls to the cutoff frequency
specified as the Release Level when the note is released.
Hold Level Determines the initial cutoff frequency at the moment the note is pressed.
Attack Level Determines the maximum cutoff frequency which the envelope reaches after a note is pressed.
Decay 1 Level Determines the cutoff frequency to which the sound changes from the Attack Level after the Decay 1 Time elapses.
Decay 2 Level Determines the cutoff frequency which will be maintained while a note is held.
Release Level Determines the final pitch reached after the note is released.
+
–
Cutoff Key Follow and Center Key
When Cutoff Key Follow is set to 100%
Large
Small
Lower range Center Key = C3 Higher range
Amount of cutoff
frequency change
0
Cutoff
Frequency
Hold
Level
Attack
Level
Decay 1
Level
Decay 2
Level
Release
Level
Release
Time
Decay2
Time
Hold
Time
Attack
Time
Decay1
Time
Pressing a key (Note On) Releasing a key (Note Off)
Time