User Manual

Reference Manual
Reference
55
Voice
Performance
Multi
SEQ Play
Master
Remote
File
Audio Rec/Play
Utility
Voice
Play
Normal Voice Edit
Common Edit
Name
Play Mode
Arpeggio
Arp Edit
Arp 1-5 Type
Controller
LFO
Filter/EG
3 Band EQ
Effect
Element Edit
OSC
Tune
PEG
Filter Type
FEG
Filter Scale
AMP Level/Pan
AEG
AMP Scale
LFO
EQ
Drum Voice Edit
Common Edit
Name
Play Mode
Arpeggio
Controller
Filter/EG
3 Band EQ
Effect
Key Edit
OSC
Tune
Filter Type
AMP Level/Pan
AEG
EQ
Job
Recall
Bulk
Supplementary Info.
Basic Structure
Appendix
Segment (EG Time Velocity Sensitivity Segment)
Determines the part of the Amplitude EG affected by the Time Vel Sens parameter.
Settings: attack, atk+dcy, decay, atk+rls, all
Half Damper (Half Damper Switch)
When the Half Damper Switch is set to on, you can produce a “half-pedal” effect just as on a real acoustic piano by
using the external Controller assigned to control change number 64.
Settings: off, on
Half Damper Time
Determines how quickly the sound decays to silence after the key is released while holding down the Foot Controller
FC3 with the Half Damper parameter turned on. After releasing the key, you can control the decay time of the sound via
the Foot Controller position, with the Half Damper Time of the Amplitude EG being the maximum decay value and the
Release Time of the Amplitude EG being the minimum decay value. When you release the pedal, the decay time after
the key is released is equivalent to the AEG Release Time. You can create a piano-like effect by setting the Release
Time to a small value and setting the Half Damper Time to a large value.
The setting here is available only when the Half Damper parameter is set to on and you use the optional FC3 connected
to the rear panel.
Settings: 0 – 127
Time Key Follow Center Key
(EG Time Key Follow Sensitivity Center Key)
Determines the central note for the “Time Key Follow.” When the Center
Key note is played, the Amplitude EG behaves according to its actual
settings.
Settings: C -2 – G8
Time Key Follow (EG Time Key Follow Sensitivity)
Determines the degree to which the notes (specifically, their position or
octave range) affect the Amplitude EG times of the selected Element.
When this is set to a positive value, high notes result in a fast Amplitude
EG transition speed while low notes result in a slow speed. When this is
set to a negative value, high velocities result in a slow Amplitude EG
transition speed while low notes result in a fast speed. When this is set
to 0, the Amplitude EG transition speed does not change no matter
what the pressed note.
Settings: -64 – +0 – +63
Break Point 1 – 4
Determines the four Break Points by specifying the respective note numbers.
Settings: C -2 – G8
NOTE: Break Point 1 to Break Point 4 will be automatically arranged in ascending order across the keyboard.
Level Offset 1 – 4
Determines the offset value to the level at each Break Point. For details about Amplitude Scaling, refer to “Setting
example of Amplitude Scaling” (page 67) in the Supplementary information.
Settings: -128 – +0 – +127
attack Time Vel Sens affects the Attack Time.
atk+dcy (attack+decay) Time Vel Sens affects the Attack Time and Decay 1 Time.
decay Time Vel Sens affects the Decay 1/2 Time.
atk+rls (attack+release) Time Vel Sens affects the Attack Time and Release Time.
all Time Vel Sens affects all the Amplitude EG Time parameters.
AMP Scale (Amplitude Scale)
+63
+30
-40
Center key
Positive value
Negative value
Lower
range
Higher
range
Faster
speed
Slower speed