User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5 Reference Manual
234
Assignable encoders
You can assign the desired function to the GAIN/PAN/ASSIGN knob on the fader strip of each
channel, and control the function using the knob. For details on the assignable functions and
their parameters, refer to “Functions that can be assigned to the assignable encoders”
(page 235).
NOTE
• If you are logged-in as the Administrator, you can also turn on the FOR GUEST button to access
the USER DEFINED KNOBS and ASSIGNABLE ENCODER for Guest page and make
assignable knob settings for the Guest account.
• SELECTED SEND is the default setting. If SELECTED SEND is selected, you can use the
assignable encoders to adjust the send level to the MIX/MATRIX channel that is selected for
SENDS ON FADER in the Function Access Area.
• The CL3 and CL1 have only one [GAIN/PAN/ASSIGN] key, so the function
of all GAIN/PAN/ASSIGN knobs will change simultaneously. On the CL5,
you can switch the knob function in block A (left side) and block C/Master
fader section (right side) independently by using the corresponding [GAIN/
PAN/ASSIGN] keys.
• This assignment does not apply to the multifunction knobs in the
Centralogic section, since these knobs are used to control on-screen
parameters.
STEP
1. In the Function Access Area, press the SETUP button.
2. In the SETUP screen, press the USER SETUP button.
3. In the USER SETUP window, press the USER DEFINED KNOBS tab.
4. Press the button in the ASSIGNABLE ENCODER field on the USER DEFINED KNOB
page.
5. In the ASSIGNABLE ENCODER SETUP window, select the function you want to
assign.
6. Press the OK button to close the ASSIGNABLE ENCODER SETUP window.
7. Press the [GAIN/PAN/ASSIGN] key on the top panel repeatedly to select ASSIGN.
8. Operate the GAIN/PAN/ASSIGN knob on each channel strip.
USER SETUP screen
(USER DEFINED KNOBS and
ASSIGNABLE ENCODER page)
ASSIGNABLE ENCODER
SETUP window