User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
Graphic EQ, effects, and Premium Rack
Reference Manual
136
2 SIDECHAIN CUE button
Press this button on to monitor the sidechain signal sent to the CUE bus. At this time, the graph
indicates the filter response for the sidechain.
3 SIDECHAIN LISTEN button
Turn this button on to output the sidechain signal (linked to the dynamics) to the bus (such as a
STEREO bus or MIX/MATRIX bus) to which the insert channel signal is sent. At this time, the
graph indicates the response of the sidechain filters.
4 FILTER TYPE buttons
Switch the type of the main bus equalizers and sidechain filters. Main bus EQ and sidechain filter
will link as follows:
5 FREQUENCY knob
Sets the frequency band that will be controlled by the equalizer and sidechain filter.
6 Q knob
Sets the Q value (steepness) of the equalizer and sidechain filter.
As you rotate this knob clockwise, the frequency range to which the equalizer or sidechain filter
is applied will become wider.
7 THRESHOLD knob
Specifies the threshold at which the processor will begin taking an effect.
8 RATIO knob
Sets the boost/cut ratio relative to the input signal.
Rotating the knob clockwise will set the ratio for boost, and counter-clockwise for cut. Fully
rotating the knob in either direction will create the maximum effect.
9 ATTACK/RELEASE buttons
Enable you to select one of the three settings as the attack/release time for compression or boost.
Select FAST for a faster attack and faster release. Select SLOW for a faster attack and slower
release. Select AUTO to automatically adjust the attack/release time depending on the frequency
ranges.
0 MODE buttons
Specify whether the processor is triggered when the sidechain signal level exceeds the threshold
value (ABOVE), or when the level does not reach the threshold value (BELOW).
A EQ GAIN meter
Indicates the dynamically-changing EQ gain.
B THRESHOLD meter
Indicates the sidechain signal level in relation to the threshold level.
C Graph area
Displays the equalizer response.
In most cases, this area displays the reference EQ graph that indicates the frequency and intensity,
and the dynamic EQ graph that indicates the dynamically-changing EQ responses.
If SIDECHAIN CUE or SIDECHAIN LISTEN is on, this area displays the sidechain filter
response.
FILTER TYPE
(Low Shelf)
(Bell)
(Hi Shelf)
Main EQ Low Shelf Bell Hi Shelf
Sidechain filter LPF BPF HPF
Dynamic EQ graph
Reference EQ graph
Sidechain filter graph