User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
MIDI
Reference Manual
157
Using Parameter Changes to control parameters
On the CL series console, you can use a type of system exclusive messages called “Parameter Changes”
to control specific events (fader/knob operations, [ON] key on/off operations, system and user settings,
etc.) as an alternative to using Control Changes or NRPN messages.
For details on the Parameter Changes that can be transmitted and received, refer to “MIDI data format”
in the Appendices.
1. Connect the CL series console to an external device.
2. In the Function Access Area, press the SETUP button to access the SETUP screen.
3. In the center of the screen, press the MIDI/GPI button to access the MIDI/GPI
popup window.
4. Press the MIDI SETUP tab to access the MIDI SETUP page, and select the port and
MIDI channel on which Parameter Changes will be transmitted and received, as
described in “Basic MIDI settings” on page 149.
NOTE
• Parameter changes include a “device number” that specifies the transmitting or receiving device.
The transmit (Tx) channel and receive (Rx) channel specified on the MIDI SETUP page are used
as the device number.
• Please be aware that if the device number included in the transmitted Parameter Change does
not match the device number of the receiving CL console, the message will be ignored.
• Do not turn Parameter Change and Control Change transmission/reception on at the same time.
Otherwise, a large amount of data will flood the MIDI port and may cause overflows or other
problems.
5. Use the Tx button and Rx button in the PARAMETER CHANGE field to turn on
Parameter Change transmission/reception.
In this state when you operate specific parameters on the CL console, the corresponding
Parameter Change messages will be transmitted. If valid Parameter Change messages are received
from an external device, the parameters assigned to those Parameter Changes will be controlled.