User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Recorder
V5.8 Reference Manual
210
Word clock settings
In a Dante network, the leader device supplies accurate word clock to other devices on the
network. If the leader device is removed from the network or breaks down, another device will
automatically take over as the clock leader.
To make this setting, in the Function Access Area, press the SETUP button, then the WORD
CLOCK/SLOT SETUP button to access the WORD CLOCK/SLOT SETUP window.
Setting up Dante Virtual Soundcard
Install Dante Virtual Soundcard (DVS) and
Dante Controller in the computer that you
want to use for audio recording.
Make the following settings before turning
DVS on.
• Connect the GbE-compatible network port
of the computer to a GbE-compatible
network switch.
• Configure the computer to obtain an IP
address automatically
(this is the default setting).
• Set the audio format.
(Example: 48kHz, 24 bit)
• Set the Dante latency. (Use a high setting to
ensure stability when using multiple
channels.)
• In the Advanced settings, select the number
of channels to be used for recording and
playback (the default is 8 x 8).
NOTE
Please refer to the Dante Virtual Soundcard User’s Guide for more information on ASIO settings
(Windows).
Dante Accelerator settings
After mounting a Dante Accelerator card on the computer, install the Dante Accelerator Driver
and make the following settings. For information about how to install the driver, refer to the
Installation Guide included with the driver.
• Use a network cable to connect the Dante jack on the Dante Accelerator card to the Dante
network, and then connect the computer’s network port to the same network.
• Configure the computer to obtain an IP address automatically (this is the default setting).
NOTE
For more information about selecting a computer for remote control from a CL series console,
refer to “Specifying DVS or Dante Accelerator” in “When setup method selection button =
SPECIFIED IP ADDRESS” (page 214).
V3.7 and earlier
V3.7