User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Setup
V5.8 Reference Manual
266
3 REMOTE
Displays the access status of the Dante settings of the external Dante devices.
• Operator: Editing is available
• Guest: Reading is available, editing is disabled
• None: Reading and editing are disabled
The display changes depending on the REMOTE settings.
• I/O DEVICE screen
• DANTE PATCH screen, DANTE SETUP DEVICE MOUNT screen
Switching the CONSOLE ID and SECONDARY PORT
DANTE SETUP window (SETUP page)
The button you switched is shown in red.
When the Dante audio network settings have been applied, the button you selected will return
to its original appearance.
NOTE
• If you change the SECONDARY PORT, you must also change the method of connection between
the CL series console and the I/O devices. For example if the connections used for the
REDUNDANT setting are left as they are when you change the setting to DAISY CHAIN, it will
become impossible to send and receive audio. Be sure to disconnect the cables before you
change the setting.
• The CONSOLE ID and SECONDARY PORT settings will not be changed even if you initialize the
CL series console.
• When the CONSOLE ID is OFF or is set to 2, 3, or 4 for a CL series console, the console’s BIT/
LATENCY will not change even if the BIT/LATENCY is changed in the DANTE SETUP window
for the CL series console within a network for which the CONSOLE ID is set to 1.
STEP
1. In the DANTE SETUP window (SETUP page), select the CONSOLE ID and the
SECONDARY PORT.
2. Press the APPLY button.
3. In the window to confirm the change, press the OK button.