Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manuale di istruzioni Руководство пользователя EN DE FR ES IT RU
Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. C A U TI ON RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
FCC INFORMATION (U.S.A.) 1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product. 2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions.
PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING * Please keep this manual in a safe place for future reference. WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following: Power supply/Power cord Water warning • Only use the voltage specified as correct for the device.
Handling caution Backup battery • Condensation can occur in the device due to rapid, drastic changes in ambient temperature—when the device is moved from one location to another, or air conditioning is turned on or off, for example. Using the device while condensation is present can cause damage. If there is reason to believe that condensation might have occurred, leave the device for several hours without turning on the power until the condensation has completely dried out.
Contents Introduction ........................................................................................................7 Related manuals and software ................................................................................................ 7 Features of the ACD1 .............................................................................................................. 7 Terms.....................................................................................................................
Introduction Thank you for purchasing the Yamaha ACD1 Amplifier Control Device. In order to take full advantage of the ACD1’s functionality and to ensure trouble-free operation, please read this owner’s manual carefully before use. After you have read the manual, keep it in a safe place for reference when needed. Related manuals and software This document explains mainly the initial connection.
Terms This section explains terminology specific to the ACD1. ■ Scene Settings such as power-on/standby or mute for each amplifier are called a “scene.” By recalling a scene, the saved settings can be immediately applied to the amplifiers. ■ Scene link Settings for simultaneously recalling scenes for multiple amplifiers within an area are called a “scene link.” By recalling a scene link, scenes can be simultaneously recalled for multiple amplifiers.
Precautions when rack-mounting the unit This unit will operate stably in an environmental temperature of 0–40°C. If you install this device together with multiple units of the same device or other devices in a EIA standard rack, the heat produced by the various devices may raise the ambient temperature inside the rack, resulting in inefficient performance. To ensure that the heat produced by this device can be dissipated appropriately, please ensure the following conditions when rackmounting it.
Preparation Connecting the AC power cable • Be sure to turn all devices OFF before connecting AC mains power. CAUTION First plug the female-connector end of the included AC cable into the [AC IN] socket on the rear panel of the ACD1, then plug the male plug into an appropriate AC outlet. Be sure to use an AC outlet of the voltage specified for the device.
Connection Examples To construct an amplifier control system, connect the ACD1 to your amplifiers and computer as follows. Amp Editor Ethernet cable Ethernet cable Network switch D-Sub cable Ethernet cable ACD1 Tn series XP series Tn series XM series PC-N series XH series Maximum of 8 amps Maximum of 32 amps Ethernet straight cable TXn series NOTE Connections between the ACD1 and computer • Use a network switch that is compatible with 100Base-TX/10Base-T.
Connection Examples Connections with the PC-N or Tn series The ACD1 allows daisy-chain connection of up to 32 PC-N or Tn series units using Ethernet cable via the [DATA PORT] connector. Connection procedure 1. Make the appropriate AMP ID and terminator settings using the [AMP ID] switches located on the rear panel of the connected amplifiers. Specify a different AMP ID for each amplifier that is connected to the same ACD1. The AMP ID will be the total of the values of the switches that are set to ON.
Connection Examples Connections with the XP, XM, or XH series Up to eight XP, XM, or XH series units can be connected to the ACD1 via the [MONITOR/REMOTE] connectors. Connection procedure 1. Connect the ACD1’s [MONITOR/REMOTE] connector to the [MONITOR/REMOTE] connector of the XP, XM, or XH series unit using a D-Sub 15-pin cable (such as a commercially-available VGA cable for a computer monitor) as shown below.
Operations that can be performed from the panel The following operations can be performed from the ACD1’s front panel. NOTE • For details, refer to the ACD1 Reference Manual. • Before use, remove the transparent protective film that was applied to the LCD prior to shipment from the factory. Category 1. Scene 2. Amp Control Sub category Recall Recalls a scene on the specified amplifier. Store Saves a scene for the specified amplifier.
Troubleshooting Symptom All scene data saved in the ACD1 has disappeared. Possible causes Response The power was turned off while the ACD1’s data was being saved. Synchronize with Amp Editor once again to transmit the settings from Amp Editor. The backup battery has run down. Check [5.Utility] → [Battery] for the state of the backup battery. If the state shows any message other than “OK,” ask qualified Yamaha service personnel to replace the backup battery. An alert message is displayed.
Information for Users on Collection and Disposal of Old Equipment EN This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
ES Información para Usuarios sobre Recolección y Disposición de Equipamiento Viejo Este símbolo en los productos, embalaje, y/o documentación que se acompañe significa que los productos electrónicos y eléctricos usados no deben ser mezclados con desechos hogareños corrientes. Para el tratamiento, recuperación y reciclado apropiado de los productos viejos, por favor llévelos a puntos de recolección aplicables, de acuerdo a su legislación nacional y las directivas 2002/96/EC.
MEMO ACD1 Owner’s Manual
For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante. NORTH AMERICA CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Scarborough, Ontario, M1S 3R1, Canada Tel: 416-298-1311 U.S.A. Yamaha Corporation of America 6600 Orangethorpe Ave., Buena Park, Calif. 90620, U.S.A.
Yamaha Pro Audio global web site: http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation © 2009 Yamaha Corporation WM15360 909POCP?.
