User Manual
Appendix
Amp Editor Owner’s Manual
211
——
HF SP
impedance too
low[Ch*]
HF imp low[*] —
The channel * speaker
impedance is too low.
Either the speaker output
connector has been
disconnected from the speaker,
or the speaker may have
malfunctioned.
Information
Continual
——
HF SP
impedance too
high[Ch*]
HF imp high[*] —
The channel * speaker
impedance is too high.
Information
Continual
——
LF SP
impedance too
low[Ch*]
LF imp low[*] —
The channel * speaker
impedance is too low.
Information
Continual
——
LF SP
impedance too
high[Ch*]
LF imp high[*] —
The channel * speaker
impedance is too low.
Information
Continual
——
Input changed
over[Ch*]
In changeover
[*]
—
The Redundant Backup
function has been
activated, and the input
signal has been switched.
There is a problem in the digital
signal being input to the slot.
Warning Continual
——
Input changed
over[Ch*]
In changeover
[*]
110
The Redundant Backup
function has been
activated, and the input
signal has been switched.
There is a problem in the digital
signal. Check the digital line
connection and confirm that the
pilot tone is input.
Warning Continual
— —
Amp f/ware
version
incompatible
Amp f/ware old —
The firmware version of
the amplifier is old, which
prevents normal
monitoring.
The amplifier must be repaired
and the firmware version must be
updated.
Contact your Yamaha dealer.
Error Single
——
PSU shutdown
[*]
PSU shutdown
[*]
—
The power supply for
channel * was shut down
because its temperature
exceeded the allowed
value.
Turn the power off, let the power
supply cool down, then turn the
power on again.
Continuous high-power output
will cause high temperatures, so
please lower the output level. If
the temperature is still high,
check whether dirt or a foreign
object could have clogged the
cooling fan, and clean the fan if
necessary.
Fault Continual
—— PSU shutdown — 101
The power supply was
shut down because its
temperature exceeded the
allowed limit.
Fault Continual
—
Synchronization
is incomplete
Sync
incomplete
—
Synchronization with Amp
Editor has not been
completed. The
synchronization operation
may have been
interrupted.
Perform the synchronization
operation once again from Amp
Editor. If this does not solve the
problem, please initialize the
memory. Should this also fails,
contact your Yamaha dealer.
Error Continual
Device information
Power turned on
Power turned
on
— The power has turned on. —
Information
Single
Power turned off Power turned off — The power has turned off. —
Information
Single
Firmware
updated
Firmware
updated
—
The firmware update has
been completed.
—
Information
Single
Device initialized Dev initialized —
Initialization has been
executed.
—
Information
Single
Panel unlocked Panel unlocked —
Panel operation lock has
been disabled.
—
Information
Single
IP address fixed IP address fixed —
The IP address has been
established.
—
Information
Single
IP address set
by DHCP
IP set by DHCP —
The network IP address
has been allocated while
operating with the DHCP
server.
—
Information
Single
IP address
released from
DHCP
IP rlsed by
DHCP
—
The network IP address
has been released while
operating with the DHCP
server.
—
Information
Single
Emergency
mode triggered
EMG triggered —
An EMG (Emergency)
signal was received, and
the device switched to
EMG mode.
Lower the input level.
Information
Single
TXn
ACD1
XMV
Message
(shown in
Amp Editor)
Message
(shown on
TXn/ACD1)
Alert number
(shown on
XMV)
Content Response Initial type
Single/
Continual