MTX3, MTX5-D, XMV Series, EXi8, EXo8 Remote Control Protocol Specifications Version 1.0.1 Release October 03, 2013 This specification document applies to MTX3, MTX5-D, XMV, EXi8, and EXo8 V1.12 and later. MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.
0. Revision History Version V1.0.0 Date Sep. 1, 2013 V1.0.1 Oct. 3, 2013 Page # 37 44,45 37 Description Initial version Added note (*1) to XMV "InputSelect" Separated Meter List of EXi8 and EXo8 Added *2 to XMV "ATT" and "DigitalATT" MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.
1. Setup 1.1. Connection Procedure Connection when using the NETWORK connector to perform remote control using this protocol MTX3 Remote Controller Ethernet Network Ethernet Switch MTX5-D Remote Controller Ethernet Network Ethernet Switch * Also for XMV, EXi8, and EXo8.
2. Command List 1. Commands from a device sent to a remote controller Reply from device No. Notification details 1-1 Device status change notification Device run mode notification 1-2 Device error status notification NOTIFY devstatus error ... 1-3 Current Fs (sampling frequency) setting notification NOTIFY devstatus fs ... 1-4 Current word clock status notification NOTIFY devstatus lockstatus ...
3. Command Specifications 3.1. Basic Command Specifications Below is the syntax of commands exchanged between a device and remote controller.
3.2.2.
1-12) Play, stop, and other transport operation notification Command Option 1 Option 2 NOTIFY event Example: MTX:AudioPlayerTransport "operation=stop" Description Stop "operation=play" Play "operation=pause" Pause Notification: NOTIFY event MTX:AudioPlayerTransport "operation=stop" Meaning: Playback was paused.
2-4) Current word clock status query Command Option 1 devstatus lockstatus Description Queries the word clock lock status Response Response string Description OK devstatus lockstatus "unlock" Unlock OK devstatus lockstatus "lock" Lock Example: Command: devstatus lockstatus Response: OK devstatus lockstatus "lock" Meaning: Query the word clock lock status. Locked 3.3.
3.3.4. Parameter query 2-10) Raw value parameter query Command Details: Option 1 Option 2 MTX:mem_MemNo /UniqueId /ElmNo /Xpos /Ypos /PrmNo /IndexNo get MemNo = UniqueId = Xpos = Ypos = IndexNo = 0 Option 3 Description 0 Raw value parameter query request See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values.
2-14) Normalized value parameter setting Command Details: Option 1 Option 2 Option 3 MTX:mem_MemNo /UniqueId /ElmNo /Xpos /Ypos /PrmNo /IndexNo 0 setn MemNo = UniqueId = Xpos = Ypos = IndexNo = 0 Option 4 (value) Description Normalized value parameter setting See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values." See section 7, "Parameter Values." (value) = See section 3.
3.3.7. Snapshot (preset) processing 2-18) Snapshot (preset) current number query processing Command Description sscurrent Queries the current preset number (index) Response Response string Description OK sscurrent (index) unmodified Current preset number queried (There is no parameter change after recalling.) OK sscurrent (index) modified Current preset number queried (There is a parameter change after recalling.
3-5) Serial number query Command Option 1 devinfo serialno Description Queries the serial number Response Response string OK devinfo serialno "xxxx" Details: Example: Description Serial number xxxx = Serial number Command: devinfo serialno Notification: OK devinfo serialno "ZA37640CHNET101001" Meaning: Query the serial number.
3.4.3. Event processing request 3-10) Time synchronization Command Option 1 event Option 2 Description MTX:AbsoluteTime "yyyy/mm/dd hh:mm:ss" Details: Changes the time yyyy = Year (Gregorian) mm = Month (1 to 12) dd = Day (1 to 31) hh = Hour (0 to 23) mm = Minute (0 to 59) ss = Second (0 to 59) * DST (Daylight Saving Time) is not accounted for.
3-15) Folder name list query Command event Option 1 Option 2 MTX:AudioPlayerGetDirNameList Details: Description "dirindex=xxxx-xxxx" Folder name list: Multiple folder name query xxxx = Index number Response Response string Description OK event MTX:AudioPlayerGetDirNameList "dirindex=xxxx-xxxx|dirname0=xxxx| ... " OKm event MTX:AudioPlayerGetDirNameList "sdcard is not inserted" Folder name list There is no SD memory card inserted. * OKm is returned if there is no SD memory card inserted.
3-19) Song playback status query Command Option 1 event Option 2 MTX:AudioPlayerGetStatus Description "" Song playback status query Response Response string Description OK event MTX:AudioPlayerGetStatus "status=stop" Stop OK event MTX:AudioPlayerGetStatus "status=play" Play OK event MTX:AudioPlayerGetStatus "status=pause" OKm event OK event MTX:AudioPlayerGetStatus "sdcard is not inserted" Pause There is no SD memory card inserted. * OKm is returned if there is no SD memory card inserted.
3.5. Command Errors 3.5.1. Command Error Notifications Error notification that indicates errors in commands. If an error is found when the command is sent, this notification is returned instead of the normal successful notification. [Notification syntax] ERROR Command name Alphanumeric Name of the command that caused the error Error code Alphanumeric Error description * See the error codes below.
4. Command Sequence Below are examples of how to process remote control. When viewed from the controller, the following major phases exist in order to perform remote control. Start procedure Normal procedure details Communication start Detects the operation • Wait for the device to start (devstatus) of controls by the user. Send request commands depending on the • Operation of a parameter control • Operation of a snapshot (preset) control • set • setn • sett • setr operation. • ssrecall, etc.
Example when the controlled device starts earlier than the controller Connected physically Remote controller Controlled device Device starting Starting NOTIFY devstatus devmode "normal" Device normal running devstatus devmode Connection unknown OK devstatus devmode "normal" Connection detection * With the first devstatus devmode request, a result notification is returned.
Meter data request/query sequence The controller requests meter data by specifying the meter data address and the minimum transmission interval. The meter transmission stops after 10 seconds. To continue receiving data, make another request before the 10 seconds pass.
5. Meter Value 1.
3.GATE DECAY Value Displayed value Value Displayed value Value Displayed value Value Displayed value 1.23sec 129 189msec 3msec 7.68sec 0 43 86 7msec 196msec 1.28sec 130 8.11sec 1 44 87 203msec 1.34sec 131 10msec 8.54sec 2 45 88 13msec 209msec 1.39sec 132 8.97sec 3 46 89 17msec 219msec 1.44sec 133 9.39sec 4 47 90 22msec 229msec 1.50sec 134 9.82sec 5 48 91 25msec 243msec 1.55sec 135 10.2sec 6 49 92 28msec 256msec 1.60sec 136 10.7sec 7 50 93 32msec 269msec 1.66sec 137 11.1sec 8 51 94 35msec 283msec 1.
4.COMPRESSOR RATIO Value Displayed value Value Displayed value Value Displayed value Value Displayed value 5.8:1 106 10.6:1 154 15.4:1 1.0:1 10 58 5.9:1 107 10.7:1 155 1.1:1 15.5:1 11 59 6.0:1 108 10.8:1 156 15.6:1 1.2:1 12 60 15.7:1 10.9:1 157 6.1:1 109 1.3:1 13 61 1.4:1 15.8:1 11.0:1 158 6.2:1 110 14 62 1.5:1 11.1:1 159 15.9:1 6.3:1 111 15 63 11.2:1 160 1.6:1 16.0:1 6.4:1 112 16 64 1.7:1 16.1:1 11.3:1 161 6.5:1 113 17 65 1.8:1 16.2:1 11.4:1 162 6.6:1 114 18 66 1.9:1 16.3:1 11.5:1 163 6.7:1 115 19 67 2.
6.EFFECT TYPE Value Displayed value 0 Reverb Hall 1 Reverb Stage1 2 Karaoke Echo 3 Vocal Echo RevHallTime/RevStageTime Value Time(sec) 0.3 0 0.4 1 0.5 2 0.6 3 0.7 4 0.8 5 0.9 6 1.0 7 1.1 8 1.2 9 1.3 10 1.4 11 1.5 12 1.6 13 1.7 14 1.8 15 1.9 16 2.0 17 2.1 18 2.2 19 2.3 20 2.4 21 2.5 22 2.6 23 2.7 24 2.8 25 2.9 26 3.0 27 3.1 28 3.2 29 3.3 30 3.4 31 3.5 32 3.6 33 3.7 34 3.8 35 3.9 36 4.0 37 4.1 38 4.2 39 4.3 40 4.4 41 4.5 42 4.6 43 7.
8.
11.
7.
Model MTX3 MTX5-D o o o o o o o o o o o o o o o o o o o o o o o o o o MemNo (Memory Number) 0 40000 40002 40003 0 40000 40002 40003 0 40000 40002 40003 0 40000 40002 40003 0 40000 40002 40003 0 40000 40002 40003 1 40000 40002 40003 40005 - 0 o o o o o o o o o o o o 0 1 - * See "4.COMPRESSOR" in "7. Parameter Values" 2 0 Knee HARD 5 - * See "4.COMPRESSOR" in "7. Parameter Values" 0 3 0 Attack 0 120 ms 0 4 0 Release 3.2m 42.600 s * See "4.COMPRESSOR" in "7.
Model MTX3 MTX5-D MemNo (Memory Number) o ElmNo (Element Number) UniqueId 60001 0 Access ID Xpos (X Position) 0-7 (1-8ch) Ypos (Y Position) 0 PrmNo (Parameter Number) 0 IndexNo (Index Number) 0 Category Prarameter Name INPUT CHANNEL MUTE DCA Mute 8(16) Channel MIN MAX unit Remarks On On OFF ON - 0:OFF 1:ON DCAAssign AssignOn OFF ON - 0:OFF 1:ON GroupMaster MuteOn UNMUTED MUTED - 0:UNMUTED 1:MUTED ChName Name Charactor (UTF-8) 48byte 0-15 (1-16ch) o 1 o 0-7 (1-8ch)
Model MTX3 MTX5-D MemNo (Memory Number) o ElmNo (Element Number) UniqueId 60001 0 1 o o o o o o - 0:OFF 1:ON MUTED - 0:UNMUTED 1:MUTED Charactor (UTF-8) 48byte - 60000 0 14-21 (9-16Ch "DIRECT INPUT CH") 0 0 0 INPUT CHANNEL LEVEL DCA Fader 8 Channel Fader Level -∞ 10.00 dB dB x 100 ex.-73.60dB x 100 = -7360 0-7 (A-H) 0 0 DCAAssign AssignOn OFF ON - 0:OFF 1:ON 0 0 0 dB x 100 ex.-73.
Model MTX3 MTX5-D MemNo (Memory Number) ElmNo (Element Number) UniqueId 1 o Access ID Xpos (X Position) 0-25 ( 0- 7:CH1-8 8-13:STIN1L-3R 14-17:FxRt1L-2R 18-25:CH9-16 ) 0-15 (MATRIX1-16 SEND) 1 0 1 0-25 ( 0- 7:CH1-8 8-13:STIN1L-3R 14-17:FxRt1L-2R 18-25:CH9-16 ) 0-7 (MATRIX1-8 SEND) 2 0 1 0-33 ( 0-15:CH1-16 16-21:STIN1L-3R 22-25:CH17-24 26-33:FxRt1L-2R ) 0-15 (MATRIX1-16 SEND) 2 0 20010 0 0-21 ( 0- 7:CH1-8 8-13:STIN1L-3R 14-21:CH9-16 ) 0-3 ( 0:FX 1 SEND 1:FX 2 SEND 2:ANC 1 SEND 3:ANC 2
Model MTX3 MTX5-D o o o o o o o o o o o o o o o o o MemNo (Memory Number) ElmNo (Element Number) UniqueId 20014 20021 20014 20021 20014 20021 20014 20021 20014 20021 20014 20021 20014 20021 20014 20021 60002 0 Access ID Xpos (X Position) 0-7 (ZONE1-8) Ypos (Y Position) 0 1 PrmNo (Parameter Number) 0 IndexNo (Index Number) Category 0 Prarameter Name ANC Ambient Noise Compensator 8 Channel 0 MIN 2 0 Gap Threshold -∞ 0.00 dB Time 0.1 5.0 s 3 0 Program dB MaxGain 0.0 18.
Model MTX3 MTX5-D MemNo (Memory Number) o o o o o o o o o o o o o o o o o o o o ElmNo (Element Number) UniqueId 20019 1 20026 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 :
Model MTX3 MTX5-D o o o o o o o o o o o o o o o o o o o o o o o o MemNo (Memory Number) Access ID Xpos (X Position) ElmNo (Element Number) UniqueId 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT
Model MTX3 MTX5-D o o o o o o o o o o o o o o o o o o o o o o o MemNo (Memory Number) Access ID Xpos (X Position) ElmNo (Element Number) UniqueId 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40006:OUT1 40007:OUT2 : : 40013:OUT8 40008:OUT1 40009:OUT2 : : 40023:OUT16 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 4
Model MTX3 MTX5-D o o o o o o o o o o o o o o o o o o o o o o o o MemNo (Memory Number) ElmNo (Element Number) UniqueId 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : : 40017:OUT7 40024:OUT1 40025:OUT3 : : 40031:OUT15 40014:OUT1 40015:OUT3 : :
Model MTX3 MTX5-D o o o o o o o MemNo (Memory Number) o o o o PrmNo (Parameter Number) IndexNo (Index Number) Category Prarameter Name MIN MAX unit Remarks 0 1 0 Mute UNMUTED MUTED - 0:UNMUTED 1:MUTED 6 0 2 0 PEQOn OFF ON - 0:ON 1:OFF 0-7 (OUT1-8) 0 0 - * See "10.OUTPUT PATCH" in "7.
XMV Series Access ID Xpos (X Position) Model 4ch 8ch o 4ch D 8ch D o o o MemNo (Memory Number) 512 0 to 3 0 to 7 0 to 3 0 to 7 0 to 3 0 to 7 0 to 3 0 to 7 0 0 PrmNo (Parameter Number) 0 0 7 0 ElmNo (Element Number) UniqueId 1 4 o o o o o o o o o o o o o o o o o o o o o o o 6 2 o Ypos (Y Position) Prarameter Name IndexNo (Index Number) MIN SignalProcessing ATT *2 -99 MAX 0 unit dB Remarks Synchronized with DigitalATT 0 1 0 DigitalATT *2 -99 0 dB Synchronized with
EXi8 MemNo (Memory Number) 512 1 Access ID Xpos (X Position) ElmNo (Element Number) UniqueId 3 0 to 7 Ypos (Y Position) 0 PrmNo (Parameter Number) 0 0 1 IndexNo (Index Number) Prarameter Name MIN MAX unit SignalProcessing GAIN +V48 -6 OFF 66 ON dB - 2 Phase OFF ON - 3 On OFF ON - 4 HPFOn OFF ON - 5 HPFFrequency 20 20000 Hz MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.1 Remarks 0:OFF 1:ON 0:OFF 1:ON 0:OFF 1:ON 0:OFF 1:ON Hz x 1000 ex.
EXo8 MemNo (Memory Number) 512 1 Access ID Xpos (X Position) ElmNo (Element Number) UniqueId 3 0 to 7 Ypos (Y Position) 0 PrmNo (Parameter Number) 0 0 IndexNo (Index Number) Prarameter Name MIN SignalProcessing Polarity MAX unit Normal Inverse - 1 On OFF ON - 2 Gain -96 24 dB MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.1 Remarks 0:Normal 1:Inverse 0:OFF 1:ON dB x 10 ex. -14.
8.
Model MTX3 MTX5-D o o o o o o o o o o o o o o o Access ID MemNo UniqueId (Memory Number) 40009 o o o o o o o o o o o o o o o o o o o o o o Meter Name Type Speaker Processor 1 Way (OUTPUT CH2) gr 40010 Speaker Processor 1 Way (OUTPUT CH3) gr 40011 Speaker Processor 1 Way (OUTPUT CH4) gr 40012 Speaker Processor 1 Way (OUTPUT CH5) gr 40013 Speaker Processor 1 Way (OUTPUT CH6) gr 40014 Speaker Processor 1 Way (OUTPUT CH7) gr 40015 Speaker Processor 1 Way (OUTPUT CH8) gr 40016 Speaker
Model MTX3 MTX5-D o Access ID MemNo UniqueId (Memory Number) 40023 Category 20020 o o o o OUTPUT CHANNEL 20027 20025 o Meter Name OUTPUT PORT OUTPUT (ANALOG) 20031 20032 OUTPUT (SLOT) Type Speaker Processor 2 Way (OUTPUT CH15 (High)) gr Meter 8 Channel (OUTPUT CH1-8) level Meter 16 Channel (OUTPUT CH1-16) level Meter 8 Channel (OUTPUT CH1-8) level Meter 8 Channel (OUTPUT CH1-8) level Meter 16 Channel (SLOT IN 1-16) level MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Sp
XMV Series Model 4ch 8ch o 4ch D 8ch D Access ID MemNo UniqueId (Memory Number) 512 20000 Category - Meter Name INPUT o o o o 20001 o o o - OUTPUT Type Meter 4 Channel (ANALOG INPUT A-D, DIGITAL INPUT A-D) level Meter 8 Channel (ANALOG INPUT A-H, DIGITAL INPUT A-H) level Meter 4 Channel (OUTPUT A-D) Meter 8 Channel (OUTPUT A-H) level MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.1 Remarks See 6. Parameter Value Details.
EXi8 Access ID MemNo UniqueId (Memory Number) 512 20000 Category - Meter Name INPUT Meter 8 Channel (INPUT1-8) Type level MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.1 Remarks See Parameter Value Details.
EXo8 Access ID MemNo UniqueId (Memory Number) 512 20001 Category - Meter Name OUTPUT Meter 8 Channel (OUTPUT1-8) Type level MTX3/MTX5-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V1.0.1 Remarks See Parameter Value Details.