User Manual

ManualsBrandsYamaha ManualsActive AmplifiersActive amplifiers

Table Of Contents

MTX3, MTX5-D, MRX7-D,

XMV Series, EXi8, EXo8

Remote Control Protocol Specications

Version 3.3.1 rev13

This specication document applies to MTX3, MTX5-D, MRX7-D, XMV, EXi8, and EXo8 V3.31 and later.

Summary of content (125 pages)

PAGE 1
MTX3, MTX5-D, MRX7-D, XMV Series, EXi8, EXo8 Remote Control Protocol Specifications Version 3.3.1 rev13 This specification document applies to MTX3, MTX5-D, MRX7-D, XMV, EXi8, and EXo8 V3.31 and later.
PAGE 2
Table of contents 0. Revision History............................................................................................................................... 4 1. Setup................................................................................................................................................. 9 1.1. Connection Procedure.................................................................................................................................................... 9 1.2.
PAGE 3
Table of contents 6.2.3. 6.2.4. 6.2.5. 6.2.6. 6.2.7. 6.2.8. 6.3. EFFECT........................................................................................................................................................... 71 ZONE............................................................................................................................................................... 72 6.2.4.1. PAGING (MTX5-D only)................................................................................
PAGE 4
0. Revision History Version V1.0.0 V1.0.1 Date Sep. 1, 2013 Sep. 25, 2013 V1.0.2 Jan.14, 2014 V1.0.3 May 23, 2014 V1.3.0 Nov. 1, 2014 V2.0.3 Aug. 25, 2015 V2.1.0 Dec. 22, 2015 Section 7 7 8 3.1 3.1 3.2.4 3.2.4, 3.4.3 3.2.4, 3.4.3 3.3.1 3.3.3 3.4.3 4 4 6 7 7 7 8 3.3.
PAGE 5
0. Revision History Version V2.2.0 Date Jun.
PAGE 6
0. Revision History Version V3.0.0 Date Feb. 24, 2017 Section 2 3.3.5 3.4.2 3.4.3 3-27) 3.4.3 3-28) 4 4 5 6 6 7 7 7 7 7 7 7 7 7 7 8 8 8 8 8 8 8 Description Changed command category name "Preset recall processing" to "Preset processing request" in 2. Command List Added Notes in "Parameter setting" for "2-14) Normalized value parameter setting". Unified term "Snapshot (preset) list" to "Preset list". Simplified command names deleting "(for list)".
PAGE 7
0. Revision History Version V3.1.0 V3.2.0 Date Jun.19, 2017 Dec. 27, 2017 Section 2,3,4,6,7,8 2.1. 1-7) 1-8) 1-10) 2.2. 2-5) 2-19) 2.3. 3-10) 3-11) 3-27) 3-28) 3-31) 2.3. 3-31) 3-32) 3.2.3 3.2.4 3.2.5 3.2.5 1-10) 3.2.6 3.3.2 3.3.2 2-5) 3.3.5 2-16) 3.3.7 3.3.8 2-21) 3.4.3 3-10) 3-11) 3.3.6 2-17) 2-18) 3.4.3 3-16) 3-18) 3-20) 3-22) 3-24) 3.4.3 3-28) : 3-32) 3-38) 3-41) 3-42) 3.4.3 3-16) 3-31) 3-32) 3.4.3 3-28) 3.4.
PAGE 8
0. Revision History Version V3.3.0 V3.3.1 Date Sep. 2018 Feb. 2019 Section 4.2 7.1 8.1 8.2 8.2 8.3 8.3 8.1 8.3 Description Corrected the sample command line in sequence diagram for "Parameter sync sequence". Renamed Parameter Name "Dugan Auto Mixer" to "A.Mixer(Dugan Automixer)" in MTX3/MTX5-D part. Renamed Meter Name "Dugan AUTO MIXER" to "Dugan AUTOMIXER" in MTX3/MTX5-D part. Added "Acoustic Echo Canceller" in MRX7-D part.
PAGE 9
1. Setup 1.1. Connection Procedure Connection when using the NETWORK connector to perform remote control using this protocol MTX3 Remote Controller Ethernet Network Switch Ethernet Ethernet Network Switch Ethernet Ethernet Network Switch Ethernet MTX5-D Remote Controller MRX7-D Remote Controller * Also for XMV, EXi8 and EXo8. XMV can be controlled with the protocol in this document without MTX3, MTX5-D or MRX7-D.
PAGE 10
1. Setup 1.2. Configuring the Remote Controller MTX3, MTX5-D and MRX7-D can be controlled from an external controller through the Ethernet (NETWORK) connector and RS-232C (REMOTE) connector. XMV, EXi8 and EXo8 can be controlled from an external controller through the Ethernet (NETWORK) connector. The configuration on the remote controller side for each type of connection is shown below. Ethernet (NETWORK connector) control IP Address: Specify the IP address of the device you want to control. IP Port No.
PAGE 11
1. Setup 1.3. Device Configuration 1.3.1. MTX3, MTX5-D and MRX7-D MTX3, MTX5-D and MRX7-D can be controlled from an external controller through a NETWORK and RS-232C connector. Up to nine remote controller devices can connect simultaneously to one MTX or MRX device, eight via the NETWORK connector and one via the RS232 connector. The procedure to configure the second control port of MTX3, MTX5-D and MRX7-D is shown below, this is found in MTX-MRX Editor - System Menu- > Remote control.
PAGE 12
2. Command List 2.1. Commands from a device sent to a remote controller No. 1-1 Device status change notification 1-2 1-3 1-4 1-5 Parameter change notification 1-6 1-7 Meter information notification 1-8 Preset change notification 1-9 1-10 Snapshot change 1-11 notification 1-12 Event processing change notification 1-13 Notification details Device run mode notification Reply from device NOTIFY devstatus runmode ...
PAGE 13
2. Command List 2.3. Extended commands No.
PAGE 14
3. Command Specifications 3.1. Basic Command Specifications Below is the syntax of commands exchanged between a device and remote controller.
PAGE 15
3. Command Specifications 3.2. Commands a Device Sends to a Remote Controller 3.2.1. Device status change notification 1-1) Device run mode notification Command NOTIFY devstatus Example: Option 1 runmode Option 2 "emergency" "update" "normal" Description Emergency run mode Update mode Normal run mode Notification: NOTIFY devstatus runmode "normal" Meaning: The run mode was changed to normal mode.
PAGE 16
3. Command Specifications 3.2.2.
PAGE 17
3. Command Specifications 3.2.3. Meter information notification 1-7) Meter information notification MTX3,MTX5-D,XMV,EXi8,EXo8 Command NOTIFY mtr Details: Option 1 MTX:mtr_MemNo/UniqueId/meter Option 2 level gr Option 3 (meter) Description Level meter value gr meter value MemNo = See section 8, "Meters." UniqueId = See section 8, "Meters." (meter) = See section 5, "Meter Values.
PAGE 18
3. Command Specifications 3.2.5.
PAGE 19
3.
PAGE 20
3.
PAGE 21
3. Command Specifications 3.3. Commands for controlling a device 3.3.1. Device status query 2-1) Device run mode query Command Option 1 devstatus runmode Description Queries the run mode Response Response string OK devstatus runmode "emergency" OK devstatus runmode "update" OK devstatus runmode "normal" Example: Command: Response: Meaning: Note: Description Emergency run mode Update mode Normal run mode devstatus runmode OK devstatus runmode "normal" Query the run mode.
PAGE 22
3. Command Specifications 2-3) Current Fs (sampling frequency) status query Command Option 1 devstatus fs Description Queries Fs Response Response string OK devstatus fs "unknown" OK devstatus fs "44.1kHz" OK devstatus fs "48kHz" Example: Command: Response: Meaning: Description Fs undefined 44.1kHz 48kHz devstatus fs OK devstatus fs "44.1kHz" Query Fs. The current Fs is 44.1 kHz.
PAGE 23
3. Command Specifications 3.3.3.
PAGE 24
3. Command Specifications 2-9) Keepalive activation setting Command scpmode Option 1 keepalive Option 2 (interval) Details: (interval) = Timeout value (msec) Description Maximum interval for a client to send some kind of message, including heart beats (default setting = disabled) * Timeout value should be more than 1000. * The actual timeout value will be increased by 1 second.
PAGE 25
3. Command Specifications 3.3.4. Parameter query 2-10) Raw value parameter query MTX3,MTX5-D,XMV,EXi8,EXo8 Command get Details: Option 1 MTX:mem_MemNo/UniqueId/ElmNo/Xpos/ Ypos/PrmNo/IndexNo MemNo = UniqueId = ElmNo = Xpos = Ypos = PrmNo = IndexNo = Option 2 0 Option 3 0 Description Raw value parameter query request See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List.
PAGE 26
3. Command Specifications 2-11) Normalized value parameter query MTX3,MTX5-D,XMV,EXi8,EXo8 Command getn Details: Option 1 MTX:mem_MemNo/UniqueId/ElmNo/Xpos/ Ypos/PrmNo/IndexNo MemNo = UniqueId = ElmNo = Xpos = Ypos = PrmNo = IndexNo = Option 2 0 Option 3 0 Description Normalized value parameter query request See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List.
PAGE 27
3. Command Specifications 3.3.5. Parameter setting 2-13) Raw value parameter setting MTX3,MTX5-D,XMV,EXi8,EXo8 Command set Details: Option 1 MTX:mem_MemNo/UniqueId/ElmNo/ Xpos/Ypos/PrmNo/IndexNo MemNo = UniqueId = ElmNo = Xpos = Ypos = PrmNo = IndexNo = (value) = Option 2 0 Option 3 0 Option 4 (value) Description Raw value parameter setting See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List.
PAGE 28
3. Command Specifications 2-14) Normalized value parameter setting MTX3,MTX5-D,XMV,EXi8,EXo8 Command setn Option 1 MTX:mem_MemNo/UniqueId/ElmNo/ Xpos/Ypos/PrmNo/IndexNo Details: MemNo = UniqueId = ElmNo = Xpos = Ypos = PrmNo = IndexNo = (value) = Option 2 0 Option 3 0 Option 4 (value) Description Normalized value parameter setting See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List.
PAGE 29
3. Command Specifications 2-15) Relative value parameter setting MTX3,MTX5-D,XMV,EXi8,EXo8 Command setr Option 1 MTX:mem_MemNo/UniqueId/ElmNo/ Xpos/Ypos/PrmNo/IndexNo Details: MemNo = UniqueId = ElmNo = Xpos = Ypos = PrmNo = IndexNo = "(value)" = Note: Option 2 0 Option 3 0 Option 4 "(value)" Description Relative value set command. See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List." See section 7, "Parameter List.
PAGE 30
3. Command Specifications MRX7-D Command setr Option 1 MTX:Index_IndexNo Option 2 0 Option 3 Option 4 "(value)" 0 Description Relative value set command. Details: IndexNo = Index number assigned in Remote Control Setup List (value) = relative value to increase or decrease. (See "Fader Parameter" table in section 6 Parameter Value Details ) Note: This command is available only for fader type parameters.
PAGE 31
3. Command Specifications 3.3.6. Meter control 2-17) Transmission request MTX3,MTX5-D,XMV,EXi8,EXo8 Command mtrstart Details: Option 1 Option 3 MTX:mtr_MemNo/UniqueId/meter (interval) Description Requests that the specified meter data be transmitted. MemNo = See section 8, "Meter List." UniqueId = See section 8, "Meter List.
PAGE 32
3. Command Specifications 2-18) Stop request MTX3,MTX5-D,XMV,EXi8,EXo8 Command mtrstop Details: Option 1 MTX:mtr_MemNo/UniqueId/meter Description Requests that the specified meter data be stopped. MemNo = See section 8, "Meter List." UniqueId = See section 8, "Meter List." Response Response string OK mtrstop MTX:mtr_MemNo/UniqueId/meter Details: Description Meter data stop setting complete MemNo = See section 8, "Meter List." UniqueId = See section 8, "Meter List.
PAGE 33
3. Command Specifications 3.3.7. Preset processing 2-19) Preset current number query processing Command Description Queries the current preset number (index) sscurrent Response Response string OK sscurrent (index) unmodified Description Current preset number queried (There is no parameter change after recalling.) Current preset number queried (There is a parameter change after recalling.
PAGE 34
3. Command Specifications 3.4. Extended commands 3.4.1. Product information query request 3-1) MTX external control protocol version query Command Option 1 devinfo protocolver Description Queries the MTX external control protocol version Response Response string OK devinfo protocolver "xxxx" Details: Description MTX external control protocol version xxxx = Version Example: Command: Notification: Meaning: devinfo protocolver OK devinfo protocolver "1.0.0" Query the protocol version.
PAGE 35
3. Command Specifications 3-5) Serial number query Command devinfo Option 1 serialno Description Queries the serial number Response Response string OK devinfo serialno "xxxx" Details: Description Serial number xxxx = Serial number Example: Command: Notification: Meaning: devinfo serialno OK devinfo serialno "ZA37640CHNET101001" Query the serial number.
PAGE 36
3. Command Specifications 3.4.2. Preset processing request 3-8) Number of Preset lists Command Description Queries the number of preset lists Response string Description The number of preset lists ssnum Response OK ssnum (num) Details: (num) = Quantity Example: Command: Notification: Meaning: ssnum OK ssnum 51 Query the number of presets. The number of presets is 51.
PAGE 37
3. Command Specifications 3.4.3. Event processing request 3-10) Time synchronization Command event Details: yyyy = mm = dd = hh = mm = ss = Option 1 MTX:AbsoluteTime Option 2 "yyyy/mm/dd hh:mm:ss" Description Changes the time Year (Gregorian) Month (1 to 12) Day (1 to 31) Hour (0 to 23) Minute (0 to 59) Second (0 to 59) * DST (Daylight Saving Time) is not accounted for.
PAGE 38
3.
PAGE 39
3.
PAGE 40
3.
PAGE 41
3.
PAGE 42
3.
PAGE 43
3. Command Specifications 3-28) Current folder move query Command event Option 1 MTX:AudioPlayerSetCurrentDir Option 2 "dirpath=0" "dirpath=0/nnnn" Description Moves the current folder(To root folder) Moves the current folder(To sub folder) Details: Directory path (index expression) 0 : Root Folder Number(the root folder number is always fixed at 0) 0/nnnn : Root Folder Number/Sub Folder Number Note: The range of sub folder is "0" to "total number of sub folders -1".
PAGE 44
3. Command Specifications 3-30) File name query Command event Details: Note: Option 1 MTX:AudioPlayerGetFileName Option 2 "fileindex=xxxx" Description File name query xxxx = File index number The range of index numbers is "0" to "total number of files - 1". Use "3-27) Current folder information query" or "3-28) Current folder move query" to get total number of files.
PAGE 45
3. Command Specifications 3-32) File name list query Command event Details: Note: Option 1 MTX:AudioPlayerGetFileNameList Option 2 Description "fileindex=XXXX-xxxx" Folder name list: Multiple file name query XXXX = the first index number of desired range for list (index expression) xxxx = the last index number of desired range for list (index expression) → Cannot be set to a value greater than the number of files. → The first number cannot be greater than the last number.
PAGE 46
3.
PAGE 47
3.
PAGE 48
3. Command Specifications 3-38) Playback song designation Command event Option 1 Option 2 MTX:AudioPlayerSetCurrentSong "dirpath=xxxx|fileindex=yyyy" Description Playback song designation Details: xxxx= Directory path (index expression) 0 : Root Folder Number(the root folder number is always fixed at 0) 0/nnnn : Root Folder Number/Sub Folder Number yyyy= File index number Note: The range of sub folder numbers is "0" to "total number of sub folders - 1".
PAGE 49
3.
PAGE 50
3. Command Specifications 3-42) Query for alert event log as list Command event Details: Note: Option 1 MTX:EventLogGetLogList Option 2 "logindex=xxxx-xxxx" Description Query for event log list xxxx-xxxx= First index number - Last index number The range of index numbers is "0" to "total number of event logs - 1". Use "3-40) Number of alert event log query" to get total number of event logs. Remark: Do not allow exceed number of event log. First index number should be less than Last index number.
PAGE 51
3. Command Specifications 3.5. Command Errors 3.5.1. Command Error Notifications Error notification that indicates errors in commands. If an error is found when the command is sent, this notification is returned instead of the normal successful notification. [Notification syntax] Command name Error code ERROR Alphanumeric Alphanumeric Name of the command that caused the error Error description * See the error codes below.
PAGE 52
4. Command Sequence Below are examples of how to process remote control. When viewed from the controller, the following major phases exist in order to perform remote control. Start procedure Communication start • Wait for the device to start (devstatus) Initial setting • MTX external control protocol setting (scpmode) • Parameter syncing (get, set, etc.) Normal procedure • Detect operation of controls. • Receive communication from the device.
PAGE 53
4. Command Sequence 4.1. Communication start sequence The amount of time for the controller and the controlled device to start is different. Remote control is an act of controlling the controlled device from the controller, so the controller must wait for the controlled device to become ready. The controller needs to wait using the sequence below. 1.
PAGE 54
4. Command Sequence Example when the controlled device starts earlier than the controller Remote controller Connected physically Starting Controlled device Device starting Device normal running Connection unknown devstatus runmode OK devstatus runmode "normal" Connection detection * With the first devstatus runmode request, a result notification is returned. Controller can recognize that Controlled device is ready to receive commands when there is response for "devstatus runmode" command.
PAGE 55
4. Command Sequence 4.2. Parameter sync sequence Immediately after communication starts, the controller does not know anything about the most recent status of the controlled device. Therefore, the controller must query all parameters that it plans to handle. This also applies for when preset recall is executed, because the controller does not know how the device has changed.
PAGE 56
4. Command Sequence Applying the most recent status of the controller to the device Remote controller Controlled device Normally running Connection detection Apply set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 Normally running Communication possible OK set MTX:mem_512/60000/0/0/0/0/0 0 0 -7760 "-77.60" set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX Apply OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX "XXXX" set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX Apply OK set MTX:mem_XXX/XXXXX/X/X/X/X/X X X XXXX "XXXX" .....
PAGE 57
4. Command Sequence 4.4. Meter data request/query sequence The controller requests meter data by specifying the meter data address and the minimum transmission interval. The meter transmission stops after 10 seconds. To continue receiving data, make another request before the 10 seconds pass. Remote controller Controlled device mtrstart MTX:mtr_512/20020/level 1000 OutputLevelMeter request Start measuring 10 seconds OK mtrstart MTX:mtr_512/20020/level NOTIFY mtr MTX:mtr_512/20020/level level 71 71 ..
PAGE 58
4. Command Sequence 4.6. Sequence when parameters are changed by another controller If the controller sends a parameter set request, a change notification is returned immediately. However, if parameters change internally in the controlled device (this includes changes in parameters that occur as a result of a controller operation on another parameter) or due to a request from another controller, a parameter change notification is received, as shown below.
PAGE 59
5.
PAGE 60
6. Parameter Value Details 6.1. Fader parameter 6.1.1. Fader with "-Infinity to 0dB" range Value 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Data -InfdB -138.00dB -136.00dB -134.00dB -133.00dB -132.00dB -131.00dB -130.00dB -129.00dB -128.00dB -127.00dB -126.00dB -125.00dB -124.00dB -123.00dB -122.00dB -121.00dB -120.00dB -119.00dB -118.00dB -117.00dB -116.00dB -115.
PAGE 61
6. Parameter Value Details Value 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 Data -25.55dB -25.50dB -25.45dB -25.40dB -25.35dB -25.30dB -25.25dB -25.20dB -25.15dB -25.10dB -25.05dB -25.00dB -24.95dB -24.90dB -24.85dB -24.80dB -24.75dB -24.70dB -24.65dB -24.60dB -24.55dB -24.50dB -24.45dB -24.
PAGE 62
6. Parameter Value Details 6.1.2. Fader with "-Infinity to 10dB" range Value 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Data -InfdB -138.00dB -135.00dB -132.00dB -129.00dB -126.00dB -123.00dB -120.00dB -117.00dB -114.00dB -111.00dB -108.00dB -105.00dB -102.00dB -99.00dB -96.00dB -95.00dB -94.00dB -93.00dB -92.00dB -91.00dB -90.00dB -89.00dB -88.00dB -87.00dB -86.
PAGE 63
6. Parameter Value Details Value 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 Data -15.55dB -15.50dB -15.45dB -15.40dB -15.35dB -15.30dB -15.25dB -15.20dB -15.15dB -15.10dB -15.05dB -15.00dB -14.95dB -14.90dB -14.85dB -14.80dB -14.75dB -14.70dB -14.65dB -14.60dB -14.55dB -14.50dB -14.45dB -14.
PAGE 64
6. Parameter Value Details 6.2. Other parameters (MTX3, MTX5-D) 6.2.1.
PAGE 65
6. Parameter Value Details 6.2.2. INPUT CHANNEL 6.2.2.1. 3BAND EQ Q Type Value Displayed value Value Displayed value Value Displayed value Value Displayed value 0 0.1 29 0.53 58 2.8 87 15.0 1 0.105 30 0.56 59 3.0 88 16.0 2 0.11 31 0.6 60 3.2 89 17.0 3 0.12 32 0.63 61 3.3 90 18.0 4 0.125 33 0.67 62 3.5 91 19.0 5 0.13 34 0.7 63 3.8 92 20.0 6 0.14 35 0.75 64 4.0 93 21.0 7 0.15 36 0.8 65 4.2 94 22.0 8 0.16 37 0.85 66 4.5 95 24.0 9 0.17 38 0.9 67 4.7 96 25.0 10 0.18 39 0.95 68 5.0 97 27.0 11 0.19 40 1.0 69 5.
PAGE 66
6. Parameter Value Details 6.2.2.2. GATE Decay Value Displayed value Value Displayed value Value Displayed value Value Displayed value 0 3msec 43 189msec 86 1.23sec 129 7.68sec 1 7msec 44 196msec 87 1.28sec 130 8.11sec 2 10msec 45 203msec 88 1.34sec 131 8.54sec 3 13msec 46 209msec 89 1.39sec 132 8.97sec 4 17msec 47 219msec 90 1.44sec 133 9.39sec 5 22msec 48 229msec 91 1.50sec 134 9.82sec 6 25msec 49 243msec 92 1.55sec 135 10.2sec 7 28msec 50 256msec 93 1.60sec 136 10.7sec 8 32msec 51 269msec 94 1.
PAGE 67
6. Parameter Value Details Hold Value Displayed value Value Displayed value Value Displayed value Value Displayed value 0 0.02msec 54 2.01msec 108 20.2msec 162 211msec 1 0.04msec 55 2.10msec 109 20.9msec 163 222msec 2 0.07msec 56 2.19msec 110 21.6msec 164 233msec 3 0.09msec 57 2.28msec 111 22.6msec 165 245msec 4 0.11msec 58 2.36msec 112 23.6msec 166 256msec 5 0.14msec 59 2.45msec 113 25.0msec 167 267msec 6 0.16msec 60 2.54msec 114 26.4msec 168 278msec 7 0.18msec 61 2.62msec 115 27.8msec 169 289msec 8 0.
PAGE 68
6. Parameter Value Details 6.2.2.3. COMPRESSOR Ratio Value Displayed value Value Displayed value Value Displayed value Value Displayed value 10 1.0:1 58 5.8:1 106 10.6:1 154 15.4:1 11 1.1:1 59 5.9:1 107 10.7:1 155 15.5:1 12 1.2:1 60 6.0:1 108 10.8:1 156 15.6:1 13 1.3:1 61 6.1:1 109 10.9:1 157 15.7:1 14 1.4:1 62 6.2:1 110 11.0:1 158 15.8:1 15 1.5:1 63 6.3:1 111 11.1:1 159 15.9:1 16 1.6:1 64 6.4:1 112 11.2:1 160 16.0:1 17 1.7:1 65 6.5:1 113 11.3:1 161 16.1:1 18 1.8:1 66 6.6:1 114 11.4:1 162 16.2:1 19 1.
PAGE 69
6. Parameter Value Details 6.2.2.4. AGC Response Time Value Displayed value Value Displayed value 0 100msec 30 2.20sec 1 150msec 31 2.30sec 2 200msec 32 2.40sec 3 250msec 33 2.50sec 4 300msec 34 2.60sec 5 350msec 35 2.70sec 6 400msec 36 2.80sec 7 450msec 37 2.90sec 8 500msec 38 3.00sec 9 550msec 39 3.10sec 10 600msec 40 3.20sec 12 700msec 42 3.40sec 13 750msec 43 3.50sec 14 800msec 44 3.60sec 15 850msec 45 3.70sec 16 900msec 46 3.80sec 17 950msec 47 3.90sec 18 1.00sec 48 4.00sec 19 1.10sec 49 4.10sec 20 1.
PAGE 70
6. Parameter Value Details 6.2.2.5. DUGAN AUTOMIXER Mode Value Displayed value 0 Mute 1 Man 2 Auto Weight Value Displayed value -3000 -100.0 -2950 -29.5 -2900 -29.0 -2850 -28.5 : : : : -100 -1.0 -50 -0.5 0 0.0 50 0.5 100 1.0 : : : : 1350 13.5 1400 14.0 1450 14.5 1500 15.0 Group MTX3 MTX5-D Value Displayed value 0 a 1 b Value Displayed value 0 a 1 b 2 c 3 d MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.3.
PAGE 71
6. Parameter Value Details 6.2.3. EFFECT Type Value 0 1 2 3 Displayed value Reverb Hall Reverb Stage1 Karaoke Echo Vocal Echo RevHallTime/RevStageTime Value 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Time(sec) Time (msec) Value 135.5 86 138.6 87 141.8 88 144.9 89 148.1 90 151.2 91 154.4 92 157.5 93 160.7 94 163.8 95 167.0 96 170.1 97 173.3 98 176.4 99 179.6 100 182.7 101 185.9 102 189.0 103 192.2 104 195.3 105 198.5 106 201.6 107 204.8 108 207.9 109 211.1 110 214.
PAGE 72
6. Parameter Value Details 6.2.4. ZONE 6.2.4.1.
PAGE 73
6. Parameter Value Details 6.2.4.2.
PAGE 74
6. Parameter Value Details 6.2.4.3. ANC ANC Source Same as 6.2.4.2. 1st/2nd PRIORITY / 1st/2nd Priority Ducker Priority Source ANC Ratio Value Displayed value 5 0.5:1 6 0.6:1 7 0.7:1 8 0.8:1 9 0.9:1 10 1.0:1 11 1.1:1 12 1.2:1 13 1.3:1 14 1.4:1 15 1.5:1 16 1.6:1 17 1.7:1 18 1.8:1 19 1.9:1 20 2.0:1 6.2.5. ROUTER 6.2.5.1.
PAGE 75
6. Parameter Value Details 6.2.5.2. OSCILLATOR Waveform Value Displayed value 0 SINE 100Hz 1 SINE 1kHz 2 SINE 10kHz 3 Pink 4 Burst 5 VARI 6.2.6. OUTPUT CHANNEL 6.2.6.1. 4BAND EQ Q Same as 6.2.2.1. 3BAND EQ / Q Type Same as 6.2.2.1. 3BAND EQ / Type B/W(Q) Value 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Oct. 6.672 6.534 6.403 6.158 6.044 5.934 5.728 5.537 5.359 5.193 5.037 4.891 4.753 4.623 4.499 4.271 4.165 3.968 3.876 3.704 3.546 3.472 3.331 3.139 3.023 2.914 2.764 2.
PAGE 76
6. Parameter Value Details 6.2.6.2.
PAGE 77
6. Parameter Value Details 6.2.7.2.
PAGE 78
6. Parameter Value Details 6.2.8. MY4-AEC 6.2.8.1.
PAGE 79
6. Parameter Value Details 6.3. Other parameters (MRX7-D) 6.3.1. Ambient Noise Compensator Ratio Same as 6.2.4.3. ANC ANC Ratio in "Other Parameters (MTX3,MTX5-D)" 6.3.2. Auto Gain Control Response Type Same as 6.2.2.4. AGC Response Time in "Other Parameters (MTX3,MTX5-D)" 6.3.3. Combiner 6.3.3.1. Room Combiner Source Value Displayed value 0 BGM1 1 BGM2 2 BGM3 3 BGM4 6.3.3.2. Room Combiner plus Automixer Source Same as 6.3.3.1. Room Combiner Source in "Other Parameters (MTX3,MTX5-D)" Mode Same as 6.2.2.
PAGE 80
6. Parameter Value Details 6.3.4.2. Gate/Ducking Release Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)" Decay Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)" Hold Same as 6.2.2.3. GATE Hold in "Other Parameters (MTX3,MTX5-D)" Keyin(Mono) Same as 6.3.4.1. Compressor Keyin(Mono) Keyin(Stereo) Same as 6.3.4.1. Compressor Keyin(Stereo) 6.3.4.3. Limiter Release Same as 6.2.2.3. GATE Decay in "Other Parameters (MTX3,MTX5-D)" Keyin(Mono) Same as 6.3.4.1.
PAGE 81
6. Parameter Value Details 6.3.5. Effect Type Same as 6.2.3. EFFECT Type in "Other Parameters (MTX3,MTX5-D)" RevHallTime/RevStageTime Same as 6.2.3. EFFECT RevHallTime/RevStageTime in "Other Parameters (MTX3,MTX5-D)" KaraokeTime/VocalTime Value 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 Time(msec) Value 0.4 52 3.2 53 6.4 54 9.5 55 12.7 56 15.8 57 19.0 58 22.1 59 25.3 60 28.4 61 31.6 62 34.7 63 37.9 64 41.
PAGE 82
6. Parameter Value Details 6.3.6. EQ 6.3.6.1. GEQ Q Same as 6.2.2.1. 3BAND EQ Q in "Other Parameters (MTX3,MTX5-D)" 6.3.6.2. PEQ Q Same as 6.2.2.1. 3BAND EQ Q in "Other Parameters (MTX3,MTX5-D)" B/W(Q) Same as 6.2.6.1. 4BAND EQ B/W(Q) in "Other Parameters (MTX3,MTX5-D)" Type Same as 6.2.2.1. 3BAND EQ Type in "Other Parameters (MTX3,MTX5-D)" 6.3.7. Filter 6.3.7.1. HPF/LPF/BPF Filter Type Same as 6.2.6.2. SPEAKER PROCESSOR HPF/LPF Type in "Other Parameters (MTX3,MTX5-D)" 6.3.8. Mixer 6.3.8.1.
PAGE 83
6. Parameter Value Details 6.3.9. Oscillator Waveform Same as 6.2.5.2. OSCILLATOR Waveform in "Other Parameters (MTX3,MTX5-D)" 6.3.10. Paging Range Same as 6.2.4.1. PAGING Range in "Other Parameters (MTX3,MTX5-D)" 6.3.11. Speech Privacy Select Type Value Displayed value 0 Forest 1 Seashore 2 Street 3 Building 6.3.12. Speaker Processor HPF/LPF Type Same as 6.2.6.2. SPEAKER PROCESSOR HPF/LPF Type in "Other Parameters (MTX3,MTX5-D)" PEQ Q Same as 6.2.2.1.
PAGE 84
7. Parameter List 7.1.
PAGE 85
7.
PAGE 86
7.
PAGE 87
7. Parameter List Model Access ID MemNo ElmNo Xpos Ypos MTX3 MTX5-D (Memory UniqueId (Element (X Position) (Y Position) Number) Number) 512 30000 0 0-5 0 o o (STIN1L3R) 0-2 30001 0 0-5 (STIN1L- (0:Band A o o 3R) 1:Band B 2:Band C) 0 o 0 IndexNo Category (Index Number) 0 INPUT STEREO CHANNEL INPUT CHANNEL STIN 0 1L-3R GAIN/ HPF 3BAND EQ Parameter Name MIN Digital Ch Gain 6 Channel PEQ 6 PEQ Channel 3 Band D.Gain -96.0 24.0 dB Q(*) 0.1 - 63.
PAGE 88
7. Parameter List Model Access ID MemNo ElmNo Xpos Ypos MTX3 MTX5-D (Memory UniqueId (Element (X Position) (Y Position) Number) Number) 512 60000 0 14-21 0 (9-16Ch o "DIRECT INPUT CH") 22-29 (17-24Ch "DIRECT o INPUT CH") 60001 0 14-21 0 (9-16Ch o "DIRECT INPUT CH") 22-29 (17-24Ch o "DIRECT INPUT CH") 70000 0 8-15 0 o (9-16ch) 70003 0-7 0 o (17-24ch) 20008 0 0-3 0 o (Fx.
PAGE 89
7. Parameter List Model Access ID MemNo ElmNo PrmNo IndexNo Category Xpos Ypos MTX3 MTX5-D (Memory UniqueId (Element (Parameter (Index (X Position) (Y Position) Number) Number) Number) Number) 512 20006 0 0-1 0 1 0 EFFECT o (Effect1-2) 20013 o 20006 1 o o 20013 o 20013 20006 o 20006 o o o Reverb Vocal Hall Echo Remarks * See "6.2.3. EFFECT" in "6. Parameter Values" 10.0 s * See "6.2.3. EFFECT" in "6. Parameter Values" 1 RevStage 0.3 Time 10.0 s * See "6.2.3. EFFECT" in "6.
PAGE 90
7.
PAGE 91
7.
PAGE 92
7. Parameter List Model Access ID MemNo ElmNo Xpos Ypos MTX3 MTX5-D (Memory UniqueId (Element (X Position) (Y Position) Number) Number) o 512 20013 0 0-7 0 (ZONE1-8) o 20020 o 20013 o 20020 o 20013 o 20020 20013 o o o o o o 20013 20020 20011 0 20014 0 0 o 20021 20014 o o o o o o 20014 20021 20014 3 20021 60002 0 o o 240 ms 3 Release 3.2m 42.600 s 4 Hold Source Level On s -∞ 0.00 dB dB x 100 ex.-73.
PAGE 93
7. Parameter List Model Access ID MemNo ElmNo Xpos Ypos MTX3 MTX5-D (Memory UniqueId (Element (X Position) (Y Position) Number) Number) 512 60002 1 0-7 0-7 o (ZONE1-8) (A-H) 0-15 o (ZONE1-16) 2 0 0-7 (A-H) o IndexNo Category (Index Number) 0 ZONE ZONE DCA/ MUTE 1-8(16) Parameter Name ZONE OUT DCA DCA Fader 8(16) Channel 0 MIN MAX unit DCA Assign OFF Assign On ON Group Level Master 10.
PAGE 94
7.
PAGE 95
7.
PAGE 96
7.
PAGE 97
7.
PAGE 98
7.
PAGE 99
7.
PAGE 100
7.
PAGE 101
7.
PAGE 102
7. Parameter List 7.2. MRX7-D Parameter Name Ch ANALOG IN ANALOG OUT Gain +48V -6 OFF 66 ON unit dB - Polarity NORMAL INVERTED - Gain -96.0 24.0 dB Polarity NORMAL INVERTED - Gain -96.0 24.0 dB Polarity NORMAL INVERTED - Gain -96.0 24.0 dB AEC ON OFF ON - NR ON OFF ON - Ambient Threshold Threshold -72 -∞ -25 0.00 dB dB Gap Threshold -∞ 0.00 dB Time 0.1 5.0 s MaxGain 0.0 18.0 dB MinGain -18.0 0.0 dB Ratio* 0.5:1 ResponseTime 1 ON OFF 2.
PAGE 103
7. Parameter List Combiner Parameter Name Room Combiner plus Master Automixer MAX unit OFF ON - Mute OFF ON - ON OFF ON - Level -∞ 10.00 dB Source* BGM1 BGM4 - ON OFF ON - Level -∞ 10.00 dB ON OFF ON - Level -∞ 10.00 dB ON OFF ON - Level -∞ 10.00 dB ON OFF ON - Level -∞ 10.00 dB Combine ON OFF ON - MicCh Mode* Mute Auto - Weight -100.0 15.0 - Override OFF ON - Override OFF ON - Mute OFF ON - OFF ON - DelayTime 0.00 50.
PAGE 104
7. Parameter List Dynamics Parameter Name Compressor Dyn Ducking Gate Limiter Paging Ducker Effect Threshold Ratio* -54 1.0:1 0 ∞:1 unit dB - Knee* HARD 5 - Attack Release* 0 3m 120 42.7 ms s Gain 0.0 18.0 dB KeyIn KeyIn* SELF KEYIN - On ON OFF ON - Dyn Threshold Range Attack Release* -54 -70 0 3m 0 0 240 42.7 dB s Hold* 0.02m 1.96 s KeyIn KeyIn* SELF KEYIN - On ON OFF ON - Dyn Threshold Range Attack Decay* -72 -70 0 3m 0 0 120 42.7 dB s Hold* 0.
PAGE 105
7. Parameter List EQ GEQ Parameter Name Property Limit ±15 -24 unit dB GEQOn OFF ON - Frequency 20.0 20.0k Hz Bypass OFF ON - Frequency 20.0 20.0k Hz Bypass OFF ON - Frequency 20.0 20.0k Hz Bypass OFF ON - GEQ Q* Gain Bypass 63.0 -24.0 OFF 0.1 15.0 ON dB - PEQ Q* 63.0 0.1 - Frequency 20.0* 20.0k Hz Gain* Bypass -18.0 OFF 18.0 ON dB - Type PEQ LPF - Property PEQOn OFF ON - Fader Level -∞ 10.
PAGE 106
7. Parameter List Mixer Parameter Name Dugan Automixer Master Ch Delay Matrix Ch MIN MAX unit Override OFF ON - Mute OFF ON - Mode* Mute Auto - Weight* -100.0 15.0 dB Group* a Override OFF b (2 - 4 Channel) d (5 - 8 Channel) h (9 - 16 Channel) ON - Level -∞ 0.00 dB On OFF ON - DelayTime 0.00 250.00 ms 500.00 Matrix Mixer Oscillator Mono Paging Ch Oscillator On Gain ZoneGroup Polarity Level -∞ 0.00 dB ON OFF ON - Level -∞ 0.
PAGE 107
7. Parameter List Speaker Processor Parameter Name In Level -∞ MAX 10.00 unit dB ON OFF ON - Delay 0.00 500.00 ms LPFFrequency 20.0 20.0k Hz HPFFrequency 20.0 20.0k Hz LPFType Thru - HPFType Thru LPFGc* HPFGc* Polarity -6 -6 NORMAL 48dB/Oct Linkwitz 48dB/Oct Linkwitz 6 6 INVERTED Center Frequency 20.0 20.0k Hz PEQ Q* 63.0 0.1 - Frequency 20.0* 20.0k Hz Gain* -18.0 18.0 dB Bypass OFF ON - Type PEQ Horn EQ - Threshold Attack -54 0.0 0 120.
PAGE 108
7. Parameter List 7.3.
PAGE 109
7. Parameter List 7.4. EXi8 Access ID ElmNo MemNo PrmNo IndexNo Xpos Ypos (Memory UniqueId (Element (Parameter (Index (X Position) (Y Position) Number) Number) Number) Number) 512 1 3 0 to 7 0 0 0 1 Parameter Name MIN Signal GAIN Processing +48V MAX unit -6 OFF 66 ON dB - 2 Phase OFF ON - 3 On OFF ON - 4 HPFOn OFF ON - 5 HPFFrequency 20 20000 Hz MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.3.
PAGE 110
7. Parameter List 7.5. EXo8 Access ID MemNo ElmNo PrmNo IndexNo Xpos Ypos (Memory UniqueId (Element (Parameter (Index (X Position) (Y Position) Number) Number) Number) Number) 512 1 3 0 to 7 0 0 0 1 2 Parameter Name Signal Polarity Processing On Gain MIN MAX unit Normal Inverse - OFF ON - -96 24 dB MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.3.1 rev13 Remarks 0:Normal 1:Inverse 0:OFF 1:ON dB x 10 ex. -14.
PAGE 111
7. Parameter List 7.6. MY4-AEC 7.6.1.
PAGE 112
8. Meter List 8.1.
PAGE 113
8.
PAGE 114
8.
PAGE 115
8. Meter List 8.2. MRX7-D Category - - - - - - - - - Meter Name 8 Channel (INPUT1-8) ANALOG OUT 8 Channel (OUTPUT1-8) YDIF IN 16 Channel (YDIF IN 1-16) SLOT IN 16 Channel (SLOT IN 1-16) SLOT OUT 16 Channel (SLOT OUT 1-16) STEREO IN 4 Channel (INPUT 1L-INPUT 2R) MY4-AEC 16 Channel (MicIn.1-4 RefIn.1-4 EchoAttn.1-4 ERL.
PAGE 116
8.
PAGE 117
8. Meter List *1 Room Combiner plus Automixer No.
PAGE 118
8. Meter List *2 Room Combiner plus Automixer No.
PAGE 119
8. Meter List *3 Dugan Automixer 2 - 4 Channel No.
PAGE 120
8. Meter List *4 Dugan Automixer 5 - 8 Channel No.
PAGE 121
8.
PAGE 122
8.
PAGE 123
8. Meter List 8.3.
PAGE 124
8. Meter List 8.4. EXi8 Access ID MemNo UniqueId (Memory Number) 512 20000 Category - Meter Name INPUT Meter 8 Channel (INPUT1-8) Type level Remarks See Parameter Value Details. MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.3.
PAGE 125
8. Meter List 8.5. EXo8 Access ID MemNo UniqueId (Memory Number) 512 20001 Category - Meter Name OUTPUT Meter 8 Channel (OUTPUT1-8) Type level Remarks See Parameter Value Details. Published Feb. 2019 MTX3/MTX5-D/MRX7-D/XMV Series/EXi8/EXo8 Remote Control Protocol Specifications V3.3.