User Manual

Appendix
Amp Editor Owner’s Manual
210
—  —
Protection
activated[Ch*]
Protection[*] —
Protection has been
activated for channel *.
For details, refer to the amplifier’s
Owner’s Manual.
Warning Continual
 — 
Limited by
protection[Ch*]
Limt by Prot.[*] 102
Protection has been
activated, and the limiter
has operated for channel *.
Continuous high-power output
may have activated protection;
lower the output level. For details
on the reason that protection was
activated, refer to Owner’s
manual. For an explanation of
why protection was activated,
refer to the Owner’s Manual.
Information Continual
 — 
Muted by
protection[Ch*]
Mute by Prot.[*] 104
Protection has been
activated, and channel *
was muted.
Error Continual
 ——
Shutdown by
protection[Ch*]
Sdwn by Prot.[*] —
Protection has been
activated, and the power
supply of channel * was
shut down.
Error Continual
—— 
Shutdown by
protection
—103
Protection has been
activated, and the power
supply was shut down.
Error Continual
—
Heatsink temp
too high[Ch*]
Htsnk too hot[*] —
The amp (heat sink) of
channel * has exceeded
the rated temperature.
Continuous high-power output
will cause high temperatures, so
please lower the input level or
attenuator. If the temperature is
still high, check whether dirt or a
foreign object could have clogged
the cooling fan’s air intake, and
clean it if necessary.
Warning Continual
—
Analog in level
too high[Ch*]
AnlgInLvl H[*] —
The analog input level of
channel * exceeds the
rated value.
Lower the input level.
Information Single
 ——
Slot in level too
high[Ch**]
SlotInLvl H[**] —
The slot input level of
channel ** exceeds the
rated value.
Information Single
 ——
MtrxMixerIn level
too high[Ch**]
MtrxInLvl H[**] —
The input level to the 4 x 4
Matrix Mixer for channel **
exceeds the rated value.
Information Single
 ——
Slot out level too
high[Ch**]
SlotOutLvl H[**] —
The slot output level of
channel ** exceeds the
rated value.
Lower the output level.
Information Single
 ——
No Output Pilot
Tone HF[Ch*]
NoOutPltToneH
[*]
—
The Signal Chain Check
function does not detect
the pilot tone (High) from
the channel * speaker
output.
Either the speaker output
connector has been
disconnected from the speaker,
or the speaker may have
malfunctioned. Check the
speaker cable and speaker
condition.
Information Continual
 ——
No Output Pilot
Tone LF[Ch*]
NoOutPltToneL
[*]
—
The Signal Chain Check
function does not detect
the pilot tone (Low) from
the channel * speaker
output.
Information Continual
—
Speaker
impedance too
high[Ch*]
Sp imp hi[*] —
The channel * speaker
impedance is too high.
The speaker connected to the
speaker output connector may
have malfunctioned.
Information Continual
—
Speaker
impedance too
low[Ch*]
Sp imp low[*] —
The channel * speaker
impedance is too low.
Information Continual
—
Output level too
high[Ch*]
OutLevel hi[*] —
The channel * output
voltage is too high.
Lower the output level.
Information Single
—
Output power too
high[Ch*]
OutPower hi[*] —
The channel * output
power is too high.
Information Single
 ——
Analog in pilot
tone lost[Ch*]
AnlgIn no PT[*] —
The pilot tone signal
included in the channel *
analog input has been lost.
The connection between the
external device and the digital
input connector may have been
broken.
Information Continual
 ——
Slot in pilot tone
lost[Ch**]
SlotIn no PT[**] —
The pilot tone signal
included in the channel **
slot input has been lost.
The connection between the
external device and the slot input
connector may have been
broken.
Information Continual
TXn ACD1 XMV
Message
(shown in
Amp Editor)
Message
(shown on
TXn/ACD1)
Alert number
(shown on
XMV)
Content Response Initial type
Single/
Continual