User Manual
Table Of Contents
- How to Use This Reference Manual
- Table of contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Monitor and Cue functions
Reference Manual
102
Monitor and Cue functions
The Monitor function lets you monitor various outputs through your nearfield monitors or
headphones. Below the front pad of the CL series console is a PHONES out jack which
always outputs the monitor source signal that you've selected for monitoring. By assigning the
MONITOR OUT L/R/C channels to the desired output jacks, you can also monitor the same
signal through external speakers.
You can select the following signals as the monitor source.
• STEREO channel output signal
• MONO channel output signal
• STEREO + MONO channel output signal
• OMNI IN 1-2, 3-4, 5-6, 7-8 channel input signal (for monitoring each two channel pair)
• RECORDER PLAYBACK output signal
• A combination of up to eight MIX, MATRIX, STEREO, or MONO channel output
signals, RECORDER PLAYBACK output signals, and OMNI IN 1-2, 3-4, 5-6, 7-8 input
signals
The Cue function lets you check an individual selected channel/DCA group by temporarily
monitoring it via MONITOR OUT or PHONES. When you press the [CUE] key on the top
panel, the cue signal of the corresponding channel or DCA group is sent as the monitor output
from the selected output port.
NOTE
The cue signal is sent to the same output destination as the monitor signal. Be aware that for this
reason, the cue signal will no longer be sent to the connected monitor speakers if you turn off the
Monitor function. However, the cue signal will always be sent to the PHONES output jack.
The following diagram shows the cue/monitor signal flow.
• MONITOR SELECT
Selects the monitor source.
• METER
Detects and indicates the level of the monitor signal or cue signal.
• DIMMER
Attenuates the monitor/cue signal by a fixed amount.