User Manual
Table Of Contents
- How to Use This Reference Manual
- Table of contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Warning/Error Messages
- Index
- Data List
- Table of Contents
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Channel Job
Reference Manual
76
9 Safe parameter select button (DCA)
For each DCA group, selects the parameters for which Recall Safe is enabled. If the ALL
button is on, all DCA master parameters will be subject to Recall Safe. If LEVEL/ON is on,
Recall Safe will apply to the DCA master level and on/off status. If NAME is on, Recall
Safe will apply to the DCA group name. Although you can turn on both the LEVEL/ON
button and the NAME button, they will then both be switched off if you turn on the ALL
button.
0 SAFE button (excluding DCA groups)
When this button is turned on, Recall Safe will be enabled for the selected channel.
NOTE
Even if a parameter is selected with the Safe Parameter Select button, Recall Safe will not be
enabled if this button is off.
A CLOSE button
Closes the window.
Channel Link function
Channel Link is a function that links the operation of parameters such as fader and EQ
between input and output channels. Two or more channels that are linked are called a “link
group”. There is no limit on the number of link groups you can create, or on the number and
combinations of channels that can be included in these link groups. You can select the types
of parameters to be linked for each link group. However, input channels and output channels
cannot coexist on the same link group.
The parameters to be linked can be selected from the following choices.
For an input channel:
• Head amp settings
• Digital gain settings
•HPF settings
•EQ settings
• Dynamics 1 settings
• Dynamics 2 settings
• Insert on and insert point settings
• Direct Out on, Direct Out level, and Direct Out point settings
• Send levels and PRE/POST settings of signals sent to MIX buses
• On/off status of signals sent to MIX buses
• Send levels and PRE/POST settings of signals sent to MATRIX buses
• On/off status of signals sent to MATRIX buses
• Fader operations
• [ON] key operations
• TO STEREO/MONO setting
•DELAY setting
• DCA GROUP ASSIGN setting
• MUTE GROUP ASSIGN settings
For an output channel:
• EQ settings
• Dynamics settings
• Insert on and insert point settings
• Send levels and PRE/POST settings of signals sent to MATRIX buses
*1
• On/off status of signals sent to MATRIX buses
*1
• Fader operations
• [ON] key operations
• TO STEREO/MONO setting
*1
• DCA GROUP ASSIGN setting
• MUTE GROUP ASSIGN settings
*1 MATRIX channel not applicable
Linking the desired input channels
This section explains how to link specific parameters of input channels.
NOTE
Channel link settings are saved as part of the scene.
STEP
1. In the Function Access Area, press the CH JOB button.
2. Press the CH LINK button in the CH JOB menu.
3. To link channels, hold down the [SEL] key for the link-source input channel and press
the [SEL] key for the link-destination channel.
4. Use the buttons of the LINK PARAMETER field in the CH LINK MODE window to
select the parameter(s) that will be linked (multiple selections are allowed).
5. If you turned on the MIX ON, MIX SEND, MATRIX ON, or MATRIX SEND buttons in
step 4, use the buttons of the SEND PARAMETER field to specify the bus(es) for
which you want operations to be linked (multiple selections are allowed).