User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Master fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/output characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Meters
Reference Manual
134
METER screen (when using 2-channel CUE)
1 CUE
Meters for CUE A and CUE B.
Function Access Area screen
If you set a bus to Surround mode in BUS SETUP, the METER screen in the Function Access
Area appears as shown below.
The display specifications are as follows.
• The meter for the SURROUND signal is shown on the left side, and the meter for the
STEREO signal is shown on the right side. The layout for L R C LFE Ls and Rs is the
same as the layout set in the SURROUND SETUP screen.
When cue is operating
• EFFECT CUE is shown on the right side, as usual.
• The 5.1 SOLO CUE display is updated on the left side. However, if CUE MODE is set to
5.1 SOLO, no cue other than 5.1 SOLO CUE is possible.
• Touch the CUE (or 5.1 SOLO) display area to clear the cue, as usual.
Using an MBCL meter bridge (optional) on the CL3
or CL1 console
If an optional meter bridge (MBCL) is installed on the CL3 or CL1 console, you will always be
able to view the output levels of MIX, MATRIX, STEREO, MONO, and CUE channels, in the
same way as in the meter section of CL5.
The MBCL meters indicate the MIX channel and MATRIX channel output levels in 12-segment
steps (OVER, -3dB, -6dB, -9dB, -12dB, -15dB, -18dB, -24dB, -30dB, -40dB, -50dB, -60dB).
You can select the metering point (the point at which the level is detected) from the following
choices. For information on how to change the metering point, refer to “Operations in the
METER screen” (page 130).
• PRE EQ .................Immediately before the EQ
• PRE FADER...........Immediately before the fader
• POST ON...............immediately after the [ON] key
1