User Manual

Setup
Reference Manual
220
RECORDER
TRANSPORT
PLAY/PAUSE, STOP,
FF/NEXT,
REW/PREVIOUS, REC
Recorder transport functions.
AUTO REC
Shortcut function for STOP  REC  PLAY.
Recording will be initiated in a single action. If
this is executed during recording, the file being
recorded will first be closed, and then recording
will continue with a new file.
REC & START
Start recording immediately without entering
record-ready mode.
DIRECT PLAY
NO ASSIGN The specified audio file will be played once from
the beginning.
Audio files to be played should be saved in the
SONGS folder inside the YPE folder. Please note
that a file cannot be specified if it is saved in the
root directory or in any other folder. When you
execute playback, the path in the TITLE LIST
screen will move to \YPE\SONGS\.
(TITLE 1)
:
SCENE
INC RECALL - Recall the scene of the next existing number.
DEC RECALL - Recall the scene of the previous existing number.
DIRECT RECALL SCENE #000-#300 Directly recall the scene of the specified number.
RECALL UNDO - Execute RECALL UNDO.
STORE UNDO - Execute STORE UNDO.
INC - Select the scene of the next existing number.
DEC -
Select the scene of the previous existing number.
RECALL - This function recalls the currently-selected scene.
STORE - Store the current settings.
SEND MODE
MIX1-16/MIX17-24,
MTRX
-
If INPUT or ST IN is selected, switch the function
of the Selected Channel section’s send encoders
from TO MIX1-16, TO MIX17-24, and MATRIX.
SENDS ON
FADER
MIX1-MIX24
NORMAL/WITH CUE
This function switches between the normal
function on/off (NORMAL), and the function
with cue on/off (WITH CUE). With the WITH
CUE option, cue will be enabled if SENDS ON
FADER mode is engaged or if you switch mode
during SENDS ON FADER mode. Also, with the
WITH CUE option, cue for all output channels
will be canceled if SENDS ON FADER mode is
disengaged.
MTRX 1-MTRX 8
MIX ON FADER
MATRIX ON FADER
SENDS ON FADER
SET BY SEL
+48V
-
Hold down this key and press SEL to switch it
on/off.
During this time, the [SEL] LED will be lit if on or
dark if off.
If [PRE SEND] is selected, “SEND ON FADER”
mode is engaged while you are holding down
the [SEL] key.
Press SEL to switch between auto/man if
[AUTOMIXER AUTO/MAN] is selected. It goes
OFF when the bank is switched.
Ø
INSERT ON
DIRECT OUT ON
PRE SEND
TO STEREO
TO MONO
TO LCR
GAIN COMPENSATION
AUTOMIXER AUTO/
MAN
FUNCTION PARAMETER 1 PARAMETER 2 Description
SET DEFAULT
VALUE
--
Press and hold this key, and then press any of
the following knobs on the panel to reset that
knob to its default value: a knob in the
SELECTED CHANNEL section, a knob in the
SELECTED CHANNEL VIEW screen, or a knob in
the Centralogic section.
It goes OFF when the bank is switched.
SET NOMI-
NAL VALUE
--
While holding down this key, press a [SEL] key
to set the fader of that channel to nominal level.
You can also push a knob in the SEND field of
the SELECTED CHANNEL VIEW screen to set the
send level to nominal level.
It goes OFF when the bank is switched.
SOLO SOLO ON - Switches solo mode on/off.
SURROUND
PAN
L ON
*5)
In Surround mode, this is used to switch the bus
assign on and off for the channel selected in list
5).
R ON
C ON
LFE ON
Ls ON
Rs ON
PANNING L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING R
PANNING Front Center
PANNING Ls
PANNING Rs
PANNING Back
PANNING Side L
*5)
In Surround mode, this is used to set hard
panning for the channel selected in list 5).
PANNING Side R
PANNING Center
PANNING TOGGLE *5)
In Surround mode, this is used to toggle the
settings for hard panning for the channel
selected in list 5).
With each press, the setting is toggled in the
following order: Center  L  Front Center  R
 Side R  Rs  Back, Ls  Side L  (Center).
TALKBACK
TALKBACK ON
LATCH Switch TALKBACK on/off.
UNLATCH
Turn TALKBACK on while pressed.
It goes OFF when the bank is switched.
SELECTED CH ASSIGN -
While holding down this key, press a SEL key of
an OUTPUT channel to switch the assignment
on/off. During this time, the [SEL] LED will be lit
if assign is ON, or dark if OFF.
The assignment setting made while holding
down this key will be stored. Pressing the key
again will recall the stored setting. Settings can
be stored in multiple keys to facilitate rapid
assignment switching.
It goes OFF when the bank is switched.
FUNCTION PARAMETER 1 PARAMETER 2 Description