User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name/icon
- HA (head amp) settings
- Sending the signal from an input channel to the STEREO/MONO bus
- Added pan function (Monaural input channels only)
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Channel name display indication
- Correcting delay between channels (Input Delay)
- Surround output for input channels
- Channel library operations
- OUTPUT channels
- EQ and Dynamics
- Channel Job
- Scene memory
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, Parametric EQ, Effects, and PREMIUM RACK
- I/O devices and external head amps
- MIDI
- Recorder
- AFC IMAGE Control
- Setup
- About the SETUP screen
- User settings
- Preferences
- USER DEFINED keys
- Functions that can be assigned to USER DEFINED keys
- USER DEFINED knobs
- Functions that can be assigned to USER DEFINED knobs
- Assignable encoders
- Functions that can be assigned to the assignable encoders
- GAIN/PAN/ASSIGN knob (assignable encoder) functions
- Custom fader bank
- Main fader
- Custom fader bank functions
- Console Lock
- Saving and loading setup data to and from a USB flash drive
- Formatting a USB flash drive
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Dante audio network settings
- Dante Device Lock
- Support for Dante Domain Manager
- Using GPI (General Purpose Interface)
- Help function
- Other functions
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Initializing the console settings and Dante audio network settings
- Update procedure for NAME SUB CPU firmware
- Update function to Dante firmware
- Warning/Error Messages
- Index
- Data List
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Parameters That Can Be Assigned to Control Changes
- NRPN Parameter Assignments
- Mixing Parameter Operation Applicability
- MIDI Data Format
- Input/Output Characteristics
- Electrical Characteristics
- Mixer Basic Parameters
- Pin Assignment
- MIDI Implementation Chart
Monitor and Cue functions
V5.8 Reference Manual
126
H SOLO ON button
Turns Solo operation on or off. A popup window will ask you to confirm Solo operation.
To execute Solo operation, press the OK button. The button will light up and SOLO
mode will be enabled. To use the Solo function, make sure this button is on, and then
turn on the [CUE] key of the desired channel or DCA. Only the corresponding channel
or DCA will be output to the buses and output jacks;
the remaining channels and DCA groups will be muted. The same signal will also be
output from the CUE OUT jacks and the MONITOR OUT jacks.
When you press this button, the MONITOR button in the Function Access Area will flash
as shown.
NOTE
If you turn on the [CUE] key of an output channel, the signal will be sent only to the corresponding
bus.
To defeat Solo, press the currently-on SOLO ON button once again.
NOTE
If you press [LAST CUE] to switch the CUE MODE from LAST to MIX (or vice versa), all
previously-enabled Cue (Solo) signals will be defeated.
CUE B field
I
USE MATRIX 7/8 AS CUE B button
When this button is pressed, channels 7 and 8 on the MATRIX bus are combined and
used as a two-channel CUE.
CUE screen (When configuring CUE B)
When the USE MATRIX 7/8 AS CUE B button is pressed, a confirmation popup window
appears. If you press the OK button, the screen expands so you can configure the CUE A/B
settings.
1 USE MATRIX 7/8 AS CUE B button
When this button is pressed to turn it off, the CUE will be only a single channel.
CUE A field
Configures the settings for CUE A.
If the CH/REMOTE switch button (
2) is set to “CH”, switching of the CUE MODE button will
be linked with CUE A/B.
In Surround mode, a 5.1 SOLO button is added to the CUE MODE field.
2
1
3
CUE A field
CUE OPERATION
MODE field
CUE B field