User Manual
Table Of Contents
- Table of contents
- Introduction
- Controls and functions
- Overview of screens
- HOME screen
- DAW REMOTE screen
- Channel-specific screens
- Other fixed display areas
- MAINTENANCE screen
- Operating Screens
- SCENE screen
- RECORDER screen
- MONITOR screen
- SETUP screen
- LOGIN screen
- HOME screen
- DAW REMOTE screen
- Channel-specific screens
- Adjusting EQ in manual mode
- Adjusting EQ in 1-knob mode
- Configuring the HPF
- Configuring GATE/DUCKING
- Adjusting the compressor in manual mode
- Adjusting the compressor in 1-knob mode
- Setting effects
- Adjusting the send to MIX/MATRIX BUS level
- Setting the send to FX BUS level
- Adjusting the send to FX/MIX/MATRIX BUS level with faders
- Using GEQ
- Using faders to adjust GEQ
- Configuring mute safe
- Setting the send levels from output channels (MIX, STEREO) to MATRIX
- Recall presets
- Editing presets
- MAINTENANCE screen
- DM3 Editor
- Using the Editor
- Appendix
General Specifications
Mixing Capacity
Input channels 16 Mono, 1 Stereo, 2 FX Return
Buses 1 Stereo, 6 Mix, 2 FX, 2 Matrix (Supports Input to Matrix)
Local Connectors
Analog IN 16 Mic/Line (12 XLR + 4 XLR/TRS Phones Combo)
Analog OUT 8 (XLR)
Dante I/O (DM3 only) 2 (etherCON : Primary/Secondary), 16 In/Out
Ethernet 1 (RJ-45)
USB to Host 1 (USB Type-B)
USB to Device 1 (USB Type-A)
Phones 1 (TRS Phones)
DC power IN 1 (XLR 4pin)
User Interface
9-inch multi-touch screen
9 x 100 mm motorized fader (Resolution=1024 steps) (8 channels + 1 main)
1 x Rotary Encoder (Touch and Turn)
Recording &
Playback
PC (via USB to Host)
(USB 2.0)
Recording 18 track
Playback 18 track
USB storage device
Recording 2 track (USB hard disk/SSD/flash memory)
Playback 2 track (USB hard disk/SSD/flash memory)
Sampling rate 96 kHz/48 kHz
Signal delay Less than 1.3 ms (CH INPUT to OMNI OUT @Fs=96 kHz)
Frequency Response
+0.5, –1.0 dB 20 Hz-20 kHz, reference to the nominal output level@1 kHz, INPUT
to OMNI OUT
THD *1
Less than 0.01% 20 Hz - 20 kHz@+4 dBu into 10 kΩ, INPUT to OMNI OUT, Input
Gain= Min
Hum & Noise *2
–126 dBu typ., Equivalent Input Noise, Input Gain= Max.
–84 dBu, Residual output noise, ST main off
Dynamic Range
110 dB typ., DA Converter,
106 dB typ., INPUT to OMNI OUT, Input Gain=Min.
Crosstalk @1 kHz *3 –100 dB, adjacent INPUT/OMNI OUT channels, Input Gain= Min.
Power Requirements DC24 V/2.5 A, PA-L500 (100 V-240 V, 50 Hz/60 Hz)
Power Consumption 43 W
Dimensions (W x H x D) 320 mm × 140 mm × 455 mm
Weight 6.5 kg
Temperature Range
Operating Temperature Range: 0 to 40°C
Storage Temperature Range: -20 to 60°C
Accessories
Owner’s Manual, Power Adapter (PA-L500, including power cord), DOWNLOAD
INFORMATION
Options Rack mount kit RK-DM3
*1 Total Harmonic Distortion is measured with a –18 dB/octave filter@80 kHz.
*2 Hum & Noise are measured with an A-Weight filter.
*3 Crosstalk is measured with a –30 dB/octave filter@22 kHz.
348
Appendix > Materials