User Manual

25
*Notes
1) The LS9 internal HA setting is converted to the HA setting of the Rio3224-D/Rio1608-D that is
controlled by the CL/QL.
2) The CL/QL has a Digital Gain setting in addition to the Attenuator setting. If the LS9 Attenuator is
set to 0 dB or higher, it is converted to a Digital Gain on the CL/QL. Furthermore, in the case of
conversion from CL/QL to LS9, the sum of the CL/QL Attenuator and Digital Gain settings are
converted to the LS9 attenuator setting. When option 4 is ticked, the LS9 Attenuator settings are
converted to CL/QL Digital Gain settings in place of CL/QL Attenuator settings, even when the
LS9 Attenuator is less than 0 dB.
3) Key in source is reproduced according to the rules in the following table.
Dynamics Keyin Source –Input Channel
LS9
Self Pre EQ
Self Post EQ
Mix 13-16
Self Post EQ
Nearby Ch
CL/QL
Self Pre EQ
Self Post EQ
Self Post EQ
Mix 21-24
Nearby Ch
Dynamics Keyin Source -Mix Channel
LS9
Self Pre EQ
Self Post EQ
Mix 13-16
Self Pre EQ
Nearby Ch
CL/QL
Self Pre EQ
Self Post EQ
Self Pre EQ
Mix 21-24
Nearby Ch
Dynamics Keyin Source -Matrix Channel
LS9
Self Pre EQ
Self Post EQ
Mix 13-16
Self Pre EQ
Matrix 1-8
CL/QL
Self Pre EQ
Self Post EQ
Self Pre EQ
Mix 21-24
Matrix 1-8
Dynamics Keyin Source -Stereo Channel
LS9
Self Pre EQ
Self Post EQ
Mix 13-16
Self Pre EQ
Stereo L/R
Mono
CL/QL
Self Pre EQ
Self Post EQ
Self Pre EQ
Mix 21-24
Stereo L/R
Mono
<Key to table> Blue field and arrow means compatible setting
Orange field and arrow means setting replaced by substitute setting
4) For the Direct Out points, if the same points cannot be selected on the conversion destination
model, the settings are adjusted appropriately and converted.
Direct Out Point -Input Channel
LS9
Pre HPF
Pre EQ
Pre Fader
CL/QL
Pre HPF
Pre EQ
Pre Fader
Post On
5) Because the LS9 Attenuator range is from -96.0 dB to +24.0 dB and the CL/QL range is from -96.0
dB to 0.0 dB, in the case of conversion from LS9 to CL/QL, limits may be placed on the settings.
6) In the case of conversion from CL/QL to LS9, the Effect units that are mounted to CL/QL Effect
Rack 1-4 are converted to blank states in LS9 GEQ/Effect Rack 1-4.
7) The M.Band Dyna. and M.Band Comp parameters between LS9 and CL/QL are different in their
types and ranges, so the settings are adjusted appropriately and converted.
M.Band Dyna. / M.Band Comp
LOW/MID/Hi. GAIN
TOTAL
EXP.RAT
MAKE UP
LS9
-96.0dB - +12.0dB
n/a
1:1 - ∞:1
n/a
CL/QL
-12.0dB - +12.0dB
0dB
1:1 - 5:1
ON
The RATIO, ATTACK, RELEASE, KNEE, and BYPASS parameters of M.Band Comp were shared
among all bands on LS9, but the parameters can be set separately for each band on CL/QL. Due to
this difference, these parameters are converted as indicated in the following figure.
- Conversion from LS9 to CL/QL:
The shared parameter settings on LS9 are
copied to the parameter settings of each
band on CL/QL.
LOW
RATIO
MID
RATIO
HI.
RATIO
ATTACK
RELEASE
KNEE
BYPASS
RATIO
ATTACK
RELEASE
KNEE
BYPASS
Copy
Copy
Copy
LS9
CL/QL