User Manual
Table Of Contents
- Contents
- An overview of MRX Designer
- Screen structure
- Basic use of MRX Designer
- Menu bar
- Tool buttons
- Shortcut keys
- Design sheet
- “Parameter Sets” area
- “Parameter Link Group” area
- “Gang Edit Group” area
- “Properties” area
- Components and the component editor
- Editing the parameters
- Acoustic Echo Canceller (AEC)
- Ambient Noise Compensator (ANC)
- Audio Detector
- Auto Gain Controller (AGC)
- Combiner
- Delay
- Dynamics
- Effect
- EQ
- Fader
- Feedback Suppressor
- Filter
- Inputs/Outputs
- Meter
- Mixer
- Oscillator
- Paging
- Polarity
- Revolabs Control
- Router
- Source Selector
- Speaker Processor
- Speech Privacy
- Text
- Transmitter/Receiver
- User Defined Block
- Dialog boxes and applications
- “Print” dialog box
- “Install Speech Privacy File” dialog box
- “File Transfer” application
- “PGM1 Label Creator” application
- “Compile” dialog box
- “Snapshot Group” dialog box
- “Remote Control Setup List” dialog box
- “External Events” dialog box
- “GPI” dialog box
- “Digital Control Panel” dialog box / “Wireless DCP” dialog box / “MCP1” dialog box
- “PGM1/PGX1” dialog box
- “Port Name” dialog box
- List of settings in “Settings” dialog boxes
- Context menus
- Troubleshooting
Tool buttons
MRX Designer User Guide
17
Tool buttons
Commands frequently used in MRX Designer, such as “Compile” and “Align Left Side,” are provided as buttons.
Button Command Summary
[Show MTX-MRX
Editor]
Shows “MTX-MRX Editor” in the foreground.
[Print] Prints the design sheet.
[Undo] Cancels the preceding operation.
*1
*1. In the [Properties] area, you can specify the operation that the [Undo]/[Redo] command will affect: either placing/
moving/deleting a component, or creating/deleting a wire between components.
[Redo] Re-executes the operation that was canceled by [Undo].
*1
[Cut] Moves the selected item to the copy buffer.
[Copy] Copies the selected item to the copy buffer.
[Paste] Pastes the item from the copy buffer to the selected location.
[Zoom In] Magnifies the display within the design sheet.
[Zoom Out] Shrinks the display within the design sheet.
--
Indicates the current magnification within the design sheet. Click to change the magnification.
You can click the numeric display area and enter a number directly.
[Zoom to 100%] Sets the display magnification in the design sheet to 100%
[Zoom to Fit] Adjusts the magnification so that all placed components can be seen in the design sheet.
[Align Left Sides] Aligns the left side to the left-most component of the selected multiple components.
[Align Horizontal
Centers]
Aligns the center of the component to the horizontal center of the selected multiple components.
[Align Right Sides] Aligns the right side to the right-most component of the selected multiple components.
[Align Tops] Aligns the top side to the highest of the selected multiple components.
[Align Vertical
Centers]
Aligns the center of the component to the vertical center of the selected multiple components.
[Align Bottoms] Aligns the bottom side to the lowest of the selected multiple components.
[Distribute
Horizontally]
Spaces the selected components evenly in the horizontal direction.
[Distribute
Vertically]
Spaces the selected components evenly in the vertical direction.
[Same Heights]
Aligns the height of the selected components. Depending on the number of ports, the height
might not align.
[Same Widths]
Aligns the width of the selected components. Depending on the port name, the width might not
align.
[Trace Signal Path]
Traces the signal path toward the output and toward the input, starting from the selected port or
wire.
[Compile]
Analyzes the placement and wiring of the MRX components included in the selected MTX/MRX
system to determine whether there are any problems.
[Preset]
Displays the “Preset” dialog box. This dialog box is the same as the “Preset” dialog box of
MTX-MRX Editor.
[Gang Edit]
Switches the gang edit group’s [Active] button on/off. If this turns on, the name of the currently
selected gang edit group is shown at the right of the button.