User Manual
Table Of Contents
- How to Use This Reference Manual
- Contents
- Function Tree
- SELECTED CHANNEL section
- Centralogic section
- Input and output patching
- Input channels
- Signal flow for input channels
- Specifying the channel name, icon and channel color
- Making HA (Head Amp) settings
- Sending a signal from an input channel to the STEREO/MONO buses
- Sending a signal from an input channel to a MIX/ MATRIX bus
- Correcting delay between channels (Input Delay)
- Channel library operations
- Output channels
- EQ and Dynamics
- Grouping and linking
- Scene memory
- About scene memories
- Using scene memories
- Editing scene memories
- Using the Global Paste function
- Using the Focus function
- Using the Recall Safe function
- Using the Fade function
- Outputting a control signal to an external device in tandem with scene recall (GPI OUT)
- Playing back an audio file that links to a scene recall
- Using Preview mode
- Monitor and Cue functions
- Talkback and Oscillator
- Meters
- Graphic EQ, effects, and Premium Rack
- I/O device and external head amp
- MIDI
- User settings (Security)
- Recorder
- Help function
- Other functions
- About the SETUP screen
- Word clock and slot settings
- Using cascade connections
- Basic settings for MIX buses and MATRIX buses
- Switching the entire phantom power supply on/ off
- Specifying the brightness of the touch screen, LEDs, channel name displays, and lamps
- Setting the date and time of the internal clock
- Setting the network address
- Initializing the unit to factory default settings
- Adjusting the detection point of the touch screen (Calibration function)
- Adjusting the faders (Calibration function)
- Fine-tuning the input and output gain (Calibration function)
- Adjusting the channel color (Calibration function)
- Adjusting the brightness of the channel name display
- Adjusting the contrast of the channel name display
- Dante audio network settings
- Using GPI (General Purpose Interface)
- Appendices
- EQ Library List
- DYNAMICS Library List
- Dynamics Parameters
- Effect Type List
- Effects Parameters
- Premium Rack Processor Parameters
- Effects and tempo synchronization
- Parameters that can be assigned to control changes
- NRPN parameter assignments
- Mixing parameter operation applicability
- Functions that can be assigned to USER DEFINED keys
- Functions that can be assigned to USER DEFINED knobs
- Functions that can be assigned to the assignable encoders
- MIDI Data Format
- Warning/Error Messages
- Electrical characteristics
- Mixer Basic Parameters
- M IDI Implementation Chart
- Index
User settings (Security)
Reference Manual
170
4. Press the button corresponding to the USER DEFINED key to which you want to
assign a function.
The USER DEFINED KEY SETUP window will appear. In this window, you can select a function
to assign to the USER DEFINED key, and select the parameters.
NOTE
The list shown is the same for all models of the CL series.
For the CL3/CL1, the display will indicate “Cannot Assign!” if you specify a parameter that does
not exist on that model.
5. Make sure that the FUNCTION field is enclosed by a frame, then use the /
buttons in the lower part of the field or the multifunction knobs on the top panel
to select the function you want to assign.
For details on the assignable functions and their parameters, refer to “Functions that can be
assigned to USER DEFINED keys” on page 259.
6. If the selected function has parameters, press the PARAMETER 1 or 2 field to move
the frame, and select parameters 1 and 2 in the same way.
7. Press the OK button to close the USER DEFINED KEY SETUP window.
8. Assign the desired functions to other USER DEFINED keys in the same way.
9. To execute an assigned function, press the corresponding USER DEFINED [1]–[16]
key on the panel.
Using the Alternate function
If you assign the Alternate function (ALTERNATE FUNCTION) to a USER DEFINED key, you will be
able to switch parameters on or off by operating the knobs in the SELECTED CHANNEL section while
pressing and holding down the USER DEFINED key.
The console enters Alternate mode when you press and hold down the USER DEFINED key to which
the Alternate function has been assigned (the key will light).
The Alternate function features two options: LATCH and UNLATCH.
If you select UNLATCH, Alternate mode is turned on only while you are pressing and holding down
the USER DEFINED key. If you select LATCH, you will be able to turn Alternate mode on or off by the
key presses. You do not need to hold down the key.
NOTE
• The console exits Alternate mode when you switch the display between the OVERVIEW screen
and the SELECTED CHANNEL VIEW screen, or when you open a popup window.
• In Alternate mode, “ALT” will be displayed in the user name field of the Function Access Area.
In Alternate mode, the following knobs change their behavior.
• [GAIN] knob
Rotate the knob to adjust the digital gain value. If DIGITAL GAIN has been selected for HA
KNOB FUNCTION on the PREFERENCE page in the USER SETUP popup window, rotate this
knob to adjust the analog gain value of the head amp.
• [MIX/MATRIX] knob
Rotate this knob to switch between PRE and POST for the corresponding send signal.
Press this knob to switch the corresponding send signal on or off.
•[HPF] knob
Press this knob to switch the high pass filter on or off.
•[DYNAMICS 1] knob
Press this knob to switch DYNAMICS 1 on or off.
•[DYNAMICS 2] knob
Press this knob to switch DYNAMICS 2 on or off.
NOTE
In Alternate mode, all knobs in the SELECTED CHANNEL section other than those knobs
mentioned above will be disabled.