User Manual

Scene memory
Reference Manual
90
On-screen buttons and corresponding parameters apply to the following channels:
0 SAFE PARAMETER SELECT field (DCA)
Enables you to select parameters for a DCA group that will be affected by Recall Safe operations.
If the ALL button is on, all DCA master parameters will be subject to Recall Safe. If LEVEL/ON
is on, the DCA master level and on/off status will be subject to Recall Safe.
3. To select the channel or DCA group that will be affected by Recall Safe operations,
press the corresponding [SEL] key.
The corresponding channel or DCA group will be enclosed by a white frame in the CH RECALL
SAFE field. (However, this white frame does not mean that the Recall Safe setting is now enabled.)
The selected channel or DCA groups 1–8 or 9–16 will be recalled to the SAFE PARAMETER
SELECT field.
NOTE
If the CH RECALL SAFE field’s SET BY SEL button is on, Recall Safe will be enabled when you
press the [SEL] key, and the corresponding channel or DCA group will be highlighted in the CH
RECALL SAFE field. You can select parameters as described in step 4 even after turning Recall
Safe on.
4. If you want to enable Recall Safe for specific parameters of the selected channel or
DCA group, make the following settings in the SAFE PARAMETER SELECT field.
NOTE
• Simply selecting a parameter in step 4 does not enable Recall Safe. To turn Recall Safe on or off,
you must also perform the operation described in step 5 (see page 91).
• While the APPLY TO ALL INPUT button (or the APPLY TO ALL OUTPUT button) is on, operations
in the SAFE PARAMETER SELECT field will apply to all input channels (or output channels).
• If an input channel is selected:
Use the buttons in the lower part of the SAFE PARAMETER SELECT field (except for the “ALL”
button) to select the parameters that will be subject to Recall Safe (multiple selections are
allowed). If you want all parameters to be subject to Recall Safe, turn on the ALL button (this is
the default setting).
• If a ST IN channel is selected:
Use the same steps as those for an input channel. (Different buttons will be displayed.)
• If a MIX channel is selected:
Use the buttons in the lower part of the SAFE PARAMETER SELECT field (except for the “ALL”
button) to select the parameters that will be subject to Recall Safe (multiple selections are allowed).
In addition, you can use the WITH MIX SEND button displayed in the lower left of the field to enable
Recall Safe for the on/off status and send level of signals sent from input channels to MIX buses.
If you want all parameters shown in the lower part of the field to be subject to Recall Safe, turn on
the ALL button (this is the default setting).
• If a MATRIX channel is selected:
Use the same steps as those for a MIX channel. (Different types of buttons will be displayed.)
• If a DCA group is selected:
If you press a [SEL] key for a DCA group, all parameters for the DCA groups (selected from DCA
groups 1–8 and DCA groups 9–16) will be displayed simultaneously. For the parameters that will
be subject to Recall Safe, you can select either “ALL” or “LEVEL/ON” (fader position and on/off
status of the [ON] key). Recall Safe will be enabled when you make this selection.
If you want all parameters of the DCA group to be subject to Recall Safe, turn on the ALL button.
Unlike when a channel is selected, Recall Safe will be enabled for that DCA group the moment
you turn on either the LEVEL/ON button or the ALL button.
Button name Corresponding parameter
Input
channel
MIX
channel
MATRIX
channel
STEREO/
MONO
channel
WITH MIX SEND Send level to the MIX bus O
WITH MATRIX SEND Send level to MATRIX bus O
ALL All parameters O O O O
HA HA-related settings O
HPF HPF settings O
EQ EQ settings O O O O
DYNA 1 Dynamics 1 settings O O O O
DYNA 2 Dynamics 2 settings O
MIX SEND Send level to MIX bus O
MATRIX SEND Send level to MATRIX bus O O O
FADER Fader settings O O O O
CH ON [ON] key settings O O O O
TO ST
On/off setting for STEREO bus
assignment, PAN, etc.
OO
MONO
On/off setting for MONO bus
assignment
OO
INPUT PATCH Input Patching O
DIGITAL GAIN Digital gain settings O
INSERT Insert on/off
O
*1
*1. ST IN channels do not feature these buttons.
OOO
INSERT PATCH Insert patch settings
O
*1
OOO
DIRECT OUT Direct Out settings
O
*1
MIX ON MIX Send On/Off O
MATRIX ON MATRIX Send On/Off O O O
DELAY Delay settings O
NAME Channel name O O O O
OUTPUT PATCH Output Patching O O O
BAL BLANCE parameter settings O
O
(stereo only)