User Manual

Effects Parameters
17 RIVAGE PM series Data List
■ Equalizer601
This effect emulates the characteristics of 70’s analog equalizers. Re-creating the distortion of typical
analog circuits will add drive to the sound.
■ Dynamic EQ
This is a newly developed equalizer that dynamically changes the EQ gain in response to the input
signal, controlling the amount of EQ cut or boost in a way similar to a compressor or expander.
■ Dynamic EQ4
Dynamic EQ4 is a two-band dynamic equalizer that has been expanded to feature four bands.
Parameter Range Description
LO TYPE HPF-2/1, LSH-1/2 Type of EQ1
LO F 16.0 Hz to 20.0 kHz Cut-off frequency of EQ1
LO G –18.0 to +18.0 dB Gain of EQ1
MID1 Q 0.50–16.0 Q of EQ2
MID1 F 16.0 Hz to 20.0 kHz Center frequency of EQ2
MID1 G –18.0 to +18.0 dB Gain of EQ2
MID2 Q 0.50–16.0 Q of EQ3
MID2 F 16.0 Hz to 20.0 kHz Center frequency of EQ3
MID2 G –18.0 to +18.0 dB Gain of EQ3
INPUT –18.0 to +18.0 dB Input gain
OUTPUT –18.0 to +18.0 dB Output gain
MID3 Q 0.50–16.0 Q of EQ4
MID3 F 16.0 Hz to 20.0 kHz Center frequency of EQ4
MID3 G –18.0 to +18.0 dB Gain of EQ4
MID4 Q 0.50–16.0 Q of EQ5
MID4 F 16.0 Hz to 20.0 kHz Center frequency of EQ5
MID4 G –18.0 to +18.0 dB Gain of EQ5
HI TYPE LPF-2/1, HSH-1/2 Type of EQ6
HI F
16.0 Hz to 20.0 kHz
*1
*1. 16.0 Hz to 20.0 kHz (LPF-1, LPF-2), 1.0 kHz to 20.0 kHz (HSH-1, HSH-2)
Cut-off frequency of EQ6
HI G –18.0 to +18.0 dB Gain of EQ6
LO SW OFF, ON Switches EQ1 on/off
MID1 SW OFF, ON Switches EQ2 on/off
MID2 SW OFF, ON Switches EQ3 on/off
MID3 SW OFF, ON Switches EQ4 on/off
MID4 SW OFF, ON Switches EQ5 on/off
HI SW OFF, ON Switches EQ6 on/off
TYPE CLEAN, DRIVE
Selects the equalizer type. The CLEAN equalizer provides non-distorted,
clear, typical digital sound, emulating variations in frequency response in
the analog circuits. The DRIVE equalizer provides distorted, driven sound
that enhances analog flavor, emulating changes in frequency response in
the analog circuits.
Parameter Range Description
BAND ON/OFF OFF, ON Turns the corresponding band on/off.
SIDECHAIN CUE OFF, ON
If this is on, the sidechain signal that controls the dynamics
will be sent to the CUE bus for monitoring.
SIDECHAIN LISTEN OFF, ON
If this is on, the sidechain signal that is linked to the dynamics
will be output to the bus (such as the STEREO bus or a MIX/
MATRIX bus) to which the inserted channel is being sent.
FILTER TYPE Low Shelf, Bell, Hi Shelf Switches the type of equalizer and sidechain filter.
FREQUENCY
(FREQ 1, FREQ 2
*1
)
*1. Actual indication in the screen encoder access field
20.0 to 20.0k Hz Frequency controlled by the equalizer and sidechain filter
Q
(Q 1, Q 2
*1
)
15.0 to 0.50 Q of the equalizer and sidechain filter
THRESHOLD
(THRESH 1, THRESH 2
*1
)
–80.0 to 10.0 dB Threshold value at which processing begins to apply
RATIO
(RATIO 1, RATIO2
*1
)
∞ : 1 to 1 : 1.50 Sets the boost/cut ratio relative to the input signal.
MODE BELOW, ABOVE
Specifies whether the processor will operate when the
sidechain signal exceeds the threshold setting (ABOVE) or
when it falls below the threshold setting (BELOW).
ATTACK/RELEASE FAST, SLOW, AUTO
Attack time/release time for when compression or boost is
applied
Parameter Range Description
BAND ON/OFF OFF, ON Switches the corresponding band on or off.
KEY IN SOURCE INT, EXT
Select main (INT) or external (EXT) as the source for the KEY IN
signal used for the corresponding band.
KEY IN CUE OFF, ON
If this button is on, the sidechain signal is sent to the CUE bus
for monitoring.
SHELF ON/OFF OFF, ON Switch the type of the equalizer and sidechain filter.
FREQUENCY 20.0 to 20.0 kHz
Frequency that is controlled by the equalizer and the sidechain
filter
Q 15.0 to 0.50 Q of the equalizer and the sidechain filter
THRESHOLD –80.0 to 10.0 dB Threshold value at which the processing effect begins to apply
RATIO ∞ : 1 to 1 : 1.50 Ratio of boost/cut for the input signal.
MODE BELOW, ABOVE
Specifies whether processing operates when the sidechain
signal exceeds the threshold value (ABOVE) or when it falls
below the value (BELOW).
ATTACK/RELEASE FAST, SLOW, AUTO
Attack time and release time at which compression or boost is
applied