User Manual

DSP-R10 Owner’s Manual
11
9 TC IN connector
This balanced XLR-3-31-type female connector
accepts time code signals from the connected
external device.
) NETWORK connector
This RJ-45 connector enables you to connect an
external device via an Ethernet cable (CAT5 or
higher). (This feature will be supported by a future
update.)
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard
RJ45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
! LINK/ACT indicator
This indicator lights up or flashes green, depending
on the connection status.
When the indicator lights up, the link has been
established. When the indicator flashes, data is being
transmitted.
@ TO CONSOLE OUT/IN connectors
These RJ-45 connectors allow this unit to be
connected to a control surface (CS-R10) via Ethernet
cables (CAT5e or higher recommended).
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard
RJ45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
# ERR indicator
This indicator flashes or lights up red if an error
occurs.
If the indicator does not turn off, please contact your
Yam a ha de a le r.
$ LINK indicator
This indicator flashes or lights up green, depending
on the network status.
% TX/RX indicators
The appropriate indicator flashes green when data is
transmitted from (TX) or received at (RX) the TO
CONSOLE [IN]/[OUT] connectors.
^ NETWORK connector
This RJ-45 connector allows the unit to be connected
to a computer via an Ethernet cable (CAT5e or higher
recommended).
This is used mainly for controlling mix parameters or
editing scene memory and libraries from the
dedicated “RIVAGE PM10 Editor” application
program.
NOTE
• Use an STP (Shielded Twisted Pair) cable to prevent
electromagnetic interference. Make sure that the metal
parts of the plugs are electrically connected to the STP
cable’s shield by conductive tape or comparable means.
• The use of Ethernet cables with Neutrik etherCON CAT5
compatible RJ-45 plugs is recommended. Standard
RJ45 plugs can also be used.
• Cable length can span up to 100 meters between
devices. Maximum practical distance may vary
depending on the cable used.
& LINK/ACT indicator
This indicator lights up or flashes green, depending
on the connection status.
When the indicator lights up, the link has been
established. When the indicator flushes, data is being
transmitted.
* HY card slots
Enable you to install optional HY cards and connect
to an I/O rack, such as RPio622, to expand I/O ports.
HY card slot 1 is used for a TWINLANe network
card exclusively. (HY card slot 2 will be supported by
a future update.) HY card slot 3 is used for a general-
purpose I/O card. HY card slot 4 is used for mult-
track recording exclusively.
This unit supports the following HY cards.
• HY256-TL
• HY144-D
For the latest information, refer to the Yamaha Pro
Audio website.
Male XLR plug
1 (ground)
3 (Cold)
2 (Hot)
Green
(flashing)
The unit is preparing to connect to the console
network. If it continues flashing for a long
time, the system is not functioning properly.
If the problem persists after taking any of the
following actions, please contact your
Yamaha dealer.
• Turn the power to the RIVAGE PM10
system off and then on.
• Make sure that the cables are connected
properly.
• Make sure that the cables are securely
inserted (locked in).
• Change to a different cable.
Green (lit
steadily)
The unit is connected to the console
network properly.