Info Sheet

22
Specifications
Dimensions
510 mm (20.1in)
599 mm (23.6in)
225 mm (8.9in)
716 mm (28.2in)
599 mm (23.6in)
225 mm (8.9in)
866 mm (34.1in)
599 mm (23.6in)
225 mm (8.9in)
TF5 TF3 TF1
General Specifications Input / Output Specifications
*1 Crosstalk is measured with a –30 dB/octave filter@22 kHz. *2 Total Harmonic Distortion is measured with a –18 dB/octave filter@80 kHz.
*3 Hum & Noise are measured with an A-Weight filter.
Fader Configuration
Mixing Capacity
I/O Connectors
Signal Processors
Recording
Sampling Frequency
Signal Delays
Fader
Frequency Response
Total Harmonic Distortion*
2
Hum & Noise*
3
Dynamic Range
Crosstalk@1 kHz
Dimensions (W x H x D)
Net Weight
Power Requirements (wattage)
Power Requirements (voltage and hertz)
Temperature Range
Included Accessories
Options
TF5
32 + 1 (Master)
32 mic/line (XLR/TRS combo)
+ 2 stereo line (RCA pin)
866 mm × 225 mm × 599 mm
(34.1in x 8.9in x 23.6in)
20.0 kg (44.1lb)
120 W
48 (40 mono + 2 stereo + 2 return)
TF3
24 + 1 (Master)
Stereo + Sub
20 (8 mono + 6 stereo)
8 DCA Groups
24 mic/line (XLR/TRS combo)
+ 2 stereo line (RCA pin)
16 (XLR)
1
8 Effects + 10 GEQ
34x34 USB Audio Interface
2-track
48 kHz
Less than 2.6 ms, INPUT to OMNI OUT, Fs=48 kHz
100 mm motorized, Resolution = 10-bit, +10 dB to –138 dB, –∞ dB all faders
+0.5, –1.5 dB 20 Hz–20 kHz, refer to +4 dBu output @1kHz, INPUT to OMNI OUT
Less than 0.05% 20 Hz–20 kHz @+4 dBu into 600 Ω, INPUT to OMNI OUT, Input Gain=Min.
–128 dBu typ., Equivalent Input Noise, Input Gain=Max.,
–85 dBu, Residual output noise, ST master off
110 dB typ., DA Converter, 107 dB typ., INPUT to OMNI OUT, Input Gain=Min.
–100 dB*
1
, adjacent INPUT/OMNI OUT channels, Input Gain=Min.
716 mm × 225 mm × 599 mm
(28.2in x 8.9in x 23.6in)
17.0 kg (37.5lb)
110 W
100–240 V 50/60 Hz
Operating temperature range: 0–40 °C
Storage temperature range: -20–60 °C
Quick Guide, Power Cord, CUBASE AI download information
Rack-mount Kit RK5014 (for TF1), Expansion Card, Foot Switch (FC5)
TF1
16 + 1 (Master)
40 (32 mono + 2 stereo + 2 return)
16 mic/line (XLR/TRS combo)
+ 2 stereo line (RCA pin)
510 mm × 225 mm × 599 mm
(20.1in x 8.9in x 23.6in)
13.5 kg (29.8lb)
100 W
Input Channels
Main Buses
Aux Buses
Groups
Inputs
Outputs
Expansion Slot
via Windows/Mac
via USB Storage Device
Internal Clock
*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain. (All faders and level controls are at maximum position.)
*2 1: GND, 2: HOT, 3: COLD *3. Tip: HOT, Ring: COLD, Sleeve: GND *4 In these specifications, 0dBu = 0.775Vrms.
*5 +48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
Analog input characteristics
balanced /
Unbalanced
Input Terminals
INPUT1-32 (TF5)
INPUT1-24 (TF3)
INPUT1-16 (TF1)
ST IN 1,2
GAIN
+66dB
-6dB
—
Load
Impedance
7.5kΩ
10kΩ
Balanced
Unbalanced
For Use With
Nominal
50-600Ω Mics
or 600Ω Lines
600Ω Lines
Sensitivity*
1
-82dBu (61.6μV)
-10dBu (245mV)
-30dBV (31.6μV)
Input Level
Nominal
-62dBu (0.616mV)
+10dBu (2.45V)
-10dBV (316mV)
Max. before clip
-42dBu (6.16mV)
+30dBu (24.5V)
+10dBV (3.16V)
Connector
Combo Jack (XLR-3-31 type *
2
or TRS phone *
3
)
RCA Pin Jack
*1 1: GND, 2: HOT, 3: COLD *2 Tip: LEFT, Ring: RIGHT, Sleeve: GND *3 In these specifications, 0dBu = 0.775Vrms. *4 All output DA converters are 24bit, 128times oversampling.
*5 The position of the level control is lowered by 16dB from the maximum.
Analog output characteristics
Output Level
Output Terminals
OMNI OUT 1-16
PHONES *
5
GAIN SW
“+24dBu” position (default)
—
Source
Impedance
75Ω
100Ω
balanced /
Unbalanced
Balanced
Unbalanced
Nominal
+4dBu (1.23 V)
3mW
Max. before clip
+24dBu (12.3 V)
75mW
Connector
XLR-3-32 type *
1
Stereo Phone Jack (TRS) *
2
For Use With
Nominal
600Ω Lines
40Ω Phones
Digital input / output specifications
Terminals
USB (TO HOST)
iPad
Format
USB
USB
Data length
24bit
—
Audio
34ch input / 34ch output, PCM
Playback: MP3 or WAV file data / Record: WAV file data
Connector
USB (B type)
USB (A type)
Control I/O specifications
Terminals
NETWORK
FOOT SW
Format
IEEE802.3
—
Level
10BASE-T/100Base-TX
—
Connector
RJ-45
TS Phone