User Manual

Toolbar
Reference Manual
TF series
- 36 -
4 with OUTPUT checkbox
Determines whether the device OUTPUT ports are connected to the console when the
console is turned on and Quick Config is enabled.
When the checkbox is turned on and if Quick Config is enabled, the device and the
console are patched automatically.
This checkbox can be turned on and off when the Quick Config button is turned off.
5 HA Control button
Determines whether the head amp of the Tio1608-D, R series and so on is controlled by
the TF series.
Turning this button ON and OFF has no effect on the DZR-D series and the DXS-XLF-D
series.
Displayed in gray when turned off, and white when turned on.
When turned off, analog gain and +48V phantom power is disabled for input channels
set to SLOT, and the current setting is displayed.
Information about the Tio1608-D
6 SYSTEM and SYNC indicators
Display the same information as the [SYSTEM] and [SYNC] indicators on the Tio1608-D.
7 Quick Config status indicator
Indicates the status of the Tio1608-D's [QUICK CONFIG] switch.
Displayed in gray when turned off, and white when turned on.
Displayed in orange if the Dante settings set by Dante Controller differ from the Quick
Config settings.
8 +48V Master status indicator
Indicates the status of the Tio1608-D's +48V Master switch.
Displayed in gray when turned off, and red when turned on.
9 Version information
Displays the version of the Tio1608-D firmware, as well as the Dante firmware contained
in the Tio1608-D.
0 Identify button
Helps you identify the connected Tio1608-D. While this button is being touched, the
LED on the corresponding Tio1608-D flashes.
NOTE
• You can use Dante Controller to change Dante patches even when the Quick Config feature is
enabled. However, Quick Config patching will be applied when you restart the console.
If you want to use Dante Controller to change these settings, disable the Quick Config feature.
• If devices that are configured by Quick Config are also locked by Dante Device Lock, a message is
displayed and the Quick Config may not be implemented. (V3.1 and later)
• Up to 24 I/O racks (such as the Tio1608-D and R series), powered speaker systems (DZR-D series),
and powered subwoofer systems (DXS-XLF-D series) can be connected within the same Dante
network. If more racks are connected, a message is displayed and the HA control may not operate
properly.
NOTE
• When Quick Config is enabled, only one TF series console that can use the OUTPUT ports of the
devices to connect can be on the same network. For DZR-D series and DXS-XLF-D series, it will
switch to the patch with the TF series that is last connected, so use the one TF series that turn on the
with OUTPUT checkbox in the network. Also, if one or more other Tio1608-D on the network have
OUTPUT ports used by another TF series console, the "with OUTPUT" check box turns off
automatically and a pop-up screen is displayed.
• When the with OUTPUT checkbox is turned off and you are using Dante Controller for patching, refer
to "Quick Config Input and input channel relationships" (page 106) for information about output port
assignments for channels.
NOTE
• When there are multiple host devices on the same network that can control the head amp, repeated
operations could result, therefore we recommend having only one host device control the head amp.
• Even when Quick Config is turned off, you can use Dante Controller to patch into the corresponding
SLOT input channel (refer to "Quick Config Input and input channel relationships" (page 106)) and
control the head amp for up to 8 I/O racks.
NOTE
If the audio signals of the Tio1608-D that corresponds to the UNIT ID button are patched, the Identify
button and various information about the Tio1608-D (error details, status, and version) are displayed,
regardless of the Quick Config button status.
շ
պ
ն
ո
չ
ջ