User Manual

ManualsBrandsYamaha ManualsMixersDigital Mixing Console

Table Of Contents

!!!"#$%$&$'()$*+,)"-)%.

!"#$%"&!$'()*+*+,(-.%/0(1/$2.(

3.45"6.7(

(

/&$012#)*.3)(.+)!04)$+,05.6$%$&$78.9)0,:)(9,;.$''"..<:.,8.-)%'$:,=4>.!,:&.

6$%$&$./?@.AB.C.DB.8>(,>8.%,;,05.-)08)4>8"..E'.:).FG.,H)+.:)*-&@.,H&)0>.

$0+.,H$+.+>I,->8.-$0.=>.*8>+.!,:&.>$-&.%,;>(@.:).!,(>4>884#.-)0:()4.,0+,I,+*$4.

9,;.)(.J*;.8>0+@.'$0.$0+.)*:'*:.4>I>48"../&>#.>I>0.$44)!.3)(.'>(8)0$4.5()*'8.

:).=>.-(>$:>+@.$44)!,05.%*4:,'4>.-&$00>48.:).=>.$+K*8:>+.8,%*4:$0>)*84#.=#.

K*8:.)0>.5>8:*(>".

/&>.%*8,-,$08.5>:.%)(>.-)0:()4@.!&,4>.:&>.8)*0+.>05,0>>(8.5>:.%)(>.:,%>.:).

3)-*8.)0.):&>(.$8'>-:8.)3.:&>.8)*0+.8#8:>%".

(

89:;<:;-( ( ( ( ( ( ( ( =>?.(

*+,( -@A%.6(B.C/$&.6.#%A( ( ( ( ( D(

D+,( 3$EF$(-.%/0( ( ( ( ( ( ( D(

D+*( 8"#G$?/&.(G&"6(H.G>/4%(-.%%$#?A( ( ( (D(

D+D( !"2$G@(<'$A%$#?(-.%%$#?A(( ( ( ( (I(

I+,( 8"#A"4.(-.%/0( ( ( ( ( ( J(

K+,( 90.#$#?(!"#$%"&!$'( ( ( ( ( L(

J+,( ;&"/M4.AN""%$#?( ( ( ( ( ( O(

(

( (

Summary of content (8 pages)

PAGE 1
MonitorMix v1.1.0 Setup Guide Welcome: Thank-you for downloading Yamaha’s MonitorMix app. It is compatible with Yamaha TF, CL & QL series mixing consoles. Up to 10 iPod touch, iPhone and iPad devices can be used with each mixer, to wirelessly control individual Mix or Aux send, pan and output levels.
PAGE 2
MonitorMix Setup Guide 1.0 System Requirements • Apple iPhone 4 or later / iPad 2 or later / iPod touch (5th generation or later) • iOS 7 or later • Yamaha CL or QL series console version 4.0 or later / TF series console version 1.12 or later. • Wi-Fi access point or router, with CAT5 cable connection to console 2.
PAGE 3
MonitorMix Setup Guide 4. Back in the Wi-Fi settings of the iOS device, the new Wi-Fi network should be selected. Press the “I” in the blue circle to access information about the network. It should show an IP Address of something like 10.0.1.3, a Subnet Mask of 255.255.255.0, a Router setting of 10.0.1.1 and a DNS setting of 10.0.1.1. 5.
PAGE 4
MonitorMix Setup Guide 5. A range of 10.0 is the default, though the other ranges are also useable. Check that there are at least 15 numbers between the Beginning and Ending of the range, because each device that connects to the network will need to be given a unique number within this range. The default range is from 2 to 200, allowing for 199 devices.
PAGE 5
MonitorMix Setup Guide 3.0 Console Setup Before connecting the Wi-Fi router to the console, check the NETWORK settings. This is found in the SETUP menu of CL & QL consoles, or in the SYSTEM SETUP of TF consoles. TF consoles support “DHCP” mode, which is ideal. However, CL & QL consoles must be given an IP address manually. I. II. III. IV.
PAGE 6
MonitorMix Setup Guide 4.0 Opening MonitorMix After launching the MonitorMix app, any CL, QL or TF mixer in the same network will be discovered and listed. 1. Select the required mixer, and touch “Connect”. 2. Enter the PIN code as set in the console’s NETWORK menu. Keep this as a secret to stop the performers changing to a different Mix. 3.
PAGE 7
MonitorMix Setup Guide 5.0 Troubleshooting The most common problems with using MonitorMix are related to Wi-Fi signal and setup. If your iOS device is connected to Wi-Fi but cannot sync with the console, check the following: • Is the console firmware and app version compatible? Check here: http://www.yamahaproaudio.com/global/en/products/peripherals/applic ations/monitormix/index.
PAGE 8
MonitorMix Setup Guide If your iOS device frequently loses connection with the console and tries to re- sync, check the following: • Are other Wi-Fi routers used in the same location, set to the same Wi- Fi channel, or an adjacent channel? (Use a Wi-Fi scanning tool to check). This would cause interference, so choose a different channel.