User Manual
Table Of Contents
- Notice regarding data copyright
- Notice regarding the content of this user guide
- Contents
- Chapter 1. An overview of MTX-MRX Editor
- An audio system control network
- Terms used in this user guide
- Data handled by MTX-MRX Editor
- Connection requirements for an MTX/MRX system
- MTX/MRX system configuration examples
- What are YDIF connections? (Cascade mode and Distribution mode)
- What are Dante connections? (Daisy-chain connection and Star connection)
- Patching
- Workflow
- About the screens
- Moving between screens
- Chapter 2. Menu bar and tool buttons
- Chapter 3. Project screen
- Chapter 4. System screen
- Chapter 5. Online and Synchronization
- Chapter 6. Presets
- Chapter 7. Dialog boxes/Software applications
- “Startup” dialog box
- “Network Setup” dialog box
- “Device Information” dialog box
- “Match Device by IP Address” dialog box
- “MTX Configuration” dialog box
- “Dante Information” dialog box
- “Word Clock” dialog box
- “Clock” dialog box
- “Daylight Saving Time” dialog box
- “Scheduler” dialog box
- “Remote Control” dialog box
- “External Events” dialog box
- “Digital Control Panel” dialog box
- “Wireless DCP” dialog box
- “MCP1” dialog box
- “PIN Setup” dialog box
- “Label” dialog box
- “Re-size Image” dialog box
- “PGM1/PGX1” dialog box
- “PGM1 Label Creator” application
- “GPI” dialog box
- “GPI Calibration” dialog box
- “Security Settings” dialog box
- “Project Information” dialog box
- “Configuration Diagram” dialog box
- “Get Log” dialog box
- “Sampling Rate Converter” dialog box
- “Input Source/Redundant” dialog box
- Appendix
“IP Address” dialog box Chapter 7. Dialog boxes/Software applications
MTX-MRX Editor User Guide
172
The following subnet masks can be selected.
❍ Default Gateway (other than MTX/MRX system devices)
Specifies the IP address of the default gateway.
● Default Gateway / DNS Server (MTX/MRX system devices only)
❍ Default Gateway
Specifies the IP address of the default gateway.
❍ DNS Server
Specifies the IP address of the DNS server.
❍ [Obtain Default Gateway and DNS Server address automatically] check box
If this is checked, the IP addresses of the default gateway and DNS server are
obtained automatically. The above IP address settings for the default gateway and
DNS server are ignored.
❍ [Apply to all devices] button
Specifies the same default gateway and DNS server settings for all devices shown in
the device list.
● [Auto-Assign IP Addresses] button
Click this to open the “Auto-Assign IP Address” dialog box.
● [OK] button
Transmits the settings to the device, and closes the dialog box.
If the device’s IP Setting is [PC] and you’ve changed the IP address, communication will
be temporarily interrupted.
● [Cancel] button
Discards the settings and closes the dialog box.
If the device’s “IP SETTINGS” is set to “UNIT ID” or “STATIC IP (Auto),” communication will not
be not possible if the network address settings differ between the computer and the unit.
Be sure to set the computer’s network address to match the network address of the unit.
If you don’t know the network address of the unit, we recommend that you use the unit’s rear
panel DIP switch to set IP Setting to [UNIT ID].
128.0.0.0 255.255.128.0
192.0.0.0 255.255.192.0
224.0.0.0 255.255.224.0
240.0.0.0 255.255.240.0
248.0.0.0 255.255.248.0
252.0.0.0 255.255.252.0
254.0.0.0 255.255.254.0
255.0.0.0 255.255.255.0 (default value)
255.128.0.0 255.255.255.128
255.192.0.0 255.255.255.192
255.224.0.0 255.255.255.224
255.240.0.0 255.255.255.240
255.248.0.0 255.255.255.248
255.252.0.0 255.255.255.252
255.254.0.0
255.255.0.0
NOTE