User Manual

Technical Data Sheet
2 / 4
I/O Rack Tio1608-D
Specifications
General Specifications
Sampling
Frequency
External
44.1kHz
+4.1667%, +0.1%, – 0.1%, – 4.0%
±200ppm
48kHz
+4.1667%, +0.1%, – 0.1%, – 4.0%
±200ppm
Signal Delay
Less than 3ms
INPUT to OUTPUT, connect with TF5 and NY64-D using Dante, Dante Receive
Latency set to 0.25ms (one way), Fs=48kHz
Frequency
Response
+0.5, -1.5dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to
OUTPUT, Fs=44.1kHz or 48kHz
Total Harmonic
Distortion
*1
Less than 0.1% +4dBu@20Hz-20kHz into 600Ω, Gain=+66dB / Less than
0.05% +4dBU@20Hz-20kHz into 600Ω, Gain=-6dB, INPUT to OUTPUT,
Fs=44.1kHz, 48kHz *Measured with a -18dB/octave filter @80kHz
Hum&Noise
*2
–128dBu typ., Equivalent Input Noise, Input Gain= +66dB
–88dBu Residual output noise, ST master off.
Dynamic Range
112dB typ., DA Converter,
108dB typ., INPUT to OUTPUT, Input Gain= Min.
Crosstalk@1kHz
–100dB
*3
, adjacent INPUT/OUTPUT channels, Input Gain= -6dB
Dimensions
(WxHxD)
480mm x 88mm
*4
x 364mm (18.9" x 3.5" x 14.3")
Net Weight
5.7kg (12.6lbs)
Power
Requirements
(wattage)
50W
Power
Requirements
(voltage and
hertz)
100-240V, 50/60Hz
Temperature
Range
Operating temperature range: 0 - 40°C
Storage temperature range: –20 - 60°C
Included
Accessories
Owner’s Manual, Power Cord(2.5m), Rubber stoppers(4)
*1 Total Harmonic Distortion is measured with 18dB/octave filter @80kHz
*2 Hum & Noise are measured with A-Weight filter.
*3 Crosstalk is measured with a 30dB/octave filter @22kHz
*4 Including rubber feet.
Analog Input Characteristics
Input
Terminals
GAIN
Actual
Load
Impedance
For Use
With
Nominal
Input Level
Connector
Sensitivly
*1
Nominal
Max.
before
clip
INPUT
1-16
+66dB
7.5k Ω
50-600Ω
Mics &
600Ω
Lines
-82dBu
(61.6μV )
–62dBu
(0.616mV)
–42dBu
(6.16mV )
Combo Jack
(XLR-3-31 type
*2
or TRS phone
*3
)
(Balanced)
–6dB
-10dBu
(245mV )
+10 dBu
(2.45V)
+30dBu
(24.5V )
*1 Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output
level when the unit is set to maximum gain.
*2 1: GND, 2: HOT, 3: COLD
*3 Tip: HOT, Ring: COLD, Sleeve: GND
* In these specifications, 0dBu = 0.775 Vrms.
* All input AD converters are 24bit linear, 128times oversampling.
* +48V DC (phantom power) is supplied to INPUT XLR type connectors via each individual software
controlled switch.
Analog Output Characteristics
Output
Terminals
Actual Source
Impedance
For Use With
Nominal
Output Level
Connector
Nominal Max. before clip
OUTPUT 1-8 75Ω 600Ω Lines +4dBu (1.23 V) +24dBu (12.3V )
XLR-3-32 type
(Balanced)
*1
*1 XLR-3-32 type connectors are balanced. (1=GND, 2=HOT, 3=COLD)
* In these specifications, 0dBu = 0.775 Vrms.
Digital I/O Characteristics
Terminals Format Data length Level Audio Connector
Primary/Secondary Dante 24bit or 32bit 1000Base-T 16ch Input/8ch Output EtherCON Cat5e