UB HOME THEATER SOUND SYSTEM TSS-10 INPUT DIGITAL 1 DIGITAL 2 ANALOG MODE DTS DIGITAL PL MOVIE PL MUSIC VOLUME TRIM 7 +6 6 +4 5 +2 INPUT 4 0 3 –2 MODE 2 –4 1 –6 REAR S.WOOFER VOLUME MUTE TEST Active Servo Technology SILENT STANDBY/ON TSS-10 HOME THEATER SOUND SYSTEM OWNER’S MANUAL TSS-10(H1)(UB)a 1 02.7.
CAUTION: READ THIS BEFORE OPERATING YOUR SYSTEM. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this sound system in a well ventilated, cool, dry, clean place with at least 20 cm on the top, 10 cm on the left and right, and 10 cm at the back of the amplifier unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.
PREPARATION FEATURES ● Home Theater Sound ● Includes Dolby Digital, Dolby Pro Logic II and DTS Decoders This system can reproduce the sound field of the software with the , or logo mark, and also reproduce normal 2-channel stereo sources in surround sound. PREPARATION FEATURES .......................................................................... 1 CHECKING THE ACCESSORIES ................................... 2 INSTALLING BATTERIES IN THE REMOTE CONTROL ................................................
CHECKING THE ACCESSORIES Check your package to make sure it contains the following items. Remote control Power cable Batteries (AAA, R03, UM-4) Fastener (1 set) (for the center speaker) Non-skid pads (3 sets: 24 pieces) INPUT MODE REAR S.WOOFER VOLUME MUTE AC adaptor (LSE9802B1540) TEST 3.
CONTROLS AND FUNCTIONS Remote control Front panel INPUT DIGITAL 1 1 DIGITAL 2 ANALOG 2 MODE 7 DTS DIGITAL PL 2 MOVIE PL MUSIC 8 PREPARATION 1 5 INPUT MODE REAR S.WOOFER VOLUME TRIM VOLUME 7 3 +6 6 +4 5 +2 4 0 9 3 –2 2 MUTE TEST –4 0 1 –6 3 4 STANDBY/ON SILENT 6 5 1 INPUT and indicators 2 MODE (k/n) and indicators Press this button repeatedly to select an input source between DIGITAL 1, DIGITAL 2 and ANALOG.
CONTROLS AND FUNCTIONS 3 VOLUME (+/–) and indicators Used for adjusting the overall volume level of this system. The current level is shown by the lighting of the indicators on the front panel. VOLUME on the front panel: Turn this control clockwise to increase the level, and counterclockwise to decrease the level. VOLUME +/– on the remote control: Press + to increase the level, and – to decrease the level.
SETTING UP THE SYSTEM Recommended speaker placement This system includes an amplifier unit, five speakers and a subwoofer. Before making connections, place all speakers in their respective positions. The positioning of the speakers is important because it controls the overall sound quality of this system. Place the speakers depending on your listening position by following the instructions below. Amplifier unit x 1 Speaker x 5 Subwoofer x 1 * The front/center/rear speakers can be mounted on a wall.
SETTING UP THE SYSTEM 䡵 Adjusting the front angle of the front/ center/rear speakers 䡵 Placing a center speaker on top of the monitor The front angle of the speakers can be adjusted as shown below. Loosen the screw on the bottom of the speaker stand. When placing the center speaker on top of the monitor, remove the stand from the speaker, and attach the provided fastener at the bottom of the speaker and on top of the monitor to prevent the speaker from falling.
CONNECTIONS CAUTION Always be sure to turn off the amplifier unit and any component to be connected when making connections. PREPARATION To ensure proper connections • Connect the white plug of the connection cable to the left “L” (white) audio signal terminal and connect the red plug to the right “R” (red) terminal. • Insert the plug securely. If the plug is not inserted securely, noise may result or sound may not be output.
CONNECTIONS Connecting audio components • For connections, use the included or commercially available connection cables suitable for respective connections. Anti-dust cap Anti-dust cap Rear panel Remove the cap covering the DIGITAL INPUTS OPTICAL terminal when connecting an optical cable. Safely store the cap and always re-insert it in the terminal when the terminal is not in use. (This cap prevents the entrance of dust.