En Es OWNER'S MANUAL MANUAL DE INSTRUCCIONES LV
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference. Install this unit in a well ventilated, cool, dry, clean place - away from direct sunlight, heat sources, vibration, dust, moisture and cold. For proper ventilation, allow the following minimum clearances.
PREPARATION En CONTENTS NAMES OF PARTS AND THEIR FUNCTIONS .................................................................................... 2 BASIC FUNCTIONS................................................................................................................................... 4 LISTENING TO FM STATIONS .............................................................................................................. 6 LISTENING TO iPod............................................................
NAMES OF PARTS AND THEIR FUNCTIONS ■ Top panel E iPod dock Set your iPod on the Lightning connector of the iPod dock. y An iPod is charged when set in the iPod dock. Note • The iPod may not be set in the iPod dock securely if it is in its protective case. • This unit stops supplying power when it is in Eco Standby mode. A Grille (☞ page 3) F VOLUME Controls volume. When you control the volume, the volume level will be displayed on the display for a while. G CLOCK Sets the clock (☞ page 4).
NAMES OF PARTS AND THEIR FUNCTIONS En Caution A grille is attached to this product to protect the speakers. • Since the grille cloth is made of soft material, it can be easily damaged, so do not scratch it with a sharp object. • Do not overstress the grille cloth. If it is overstressed, it will become contorted and damaged. This may cause damage to the speakers. Be careful when handling the grille cloth. ■ Rear panel To AC wall outlet L 12 V Connect the supplied AC adaptor.
OPERATION BASIC FUNCTIONS Adjusting the clock A Press and hold CLOCK for more than 2 seconds. The display flashes. A, C B B Adjust the time with TUNING. y If you press and hold TUNING, the numbers advance quickly. C Press CLOCK. If you want to cancel clock setting mode, press . y If you press PRESET in step B, you can select the time display method (12 hours/24 hours). Note The time settings are lost approximately one week after unplugging the unit.
BASIC FUNCTIONS En ■ Switching the alarm on/off Press ALARM. When the alarm is on, the alarm indicator ( ) and the RADIO indicator (or the iPod indicator) light and the alarm time is displayed for a while. Alarm indicator ( ) RADIO indicator iPod indicator Operations during playing back alarm sound At the set time, alarm sound plays back. During playback, operations below are available. ■ Stopping the alarm Press ALARM or .
LISTENING TO FM STATIONS Tuning radio stations A Press SOURCE to select RADIO. The RADIO indicator lights. B B For automatic tuning, press and hold TUNING. For manual tuning, press TUNING repeatedly. Note A If you tune into a station manually, the sound is monaural. RADIO indicator Presetting radio stations You can store up to five favorite FM radio stations with the preset function. A Press TUNING to select a favorite radio station. The radio frequency is displayed temporally.
En LISTENING TO iPod ■ Connecting an iPod to the iPod dock y • An iPod will be recharged while it is connected to the dock. The iPod will not be recharged when the unit is in Eco Standby mode. • If an iPod in protective case is connected by force, the connector may be damaged. Remove the protective case before connection. Note • Slowly connect or remove the iPod. • Insert the iPod straight in the right angle without adding pressure to it.
LISTENING TO EXTERNAL SOURCES A Connect your portable audio device to AUX using a commercially available 3.5 mm (1/8 in) mini plug cable. Rear panel A B C Note Turn down the volume of this unit and your portable audio device before connection. B Turn on the system. C Press SOURCE to set the playback source to AUX. The AUX indicator lights. AUX indicator 8 En D Start playback on the connected portable audio device.
En TROUBLESHOOTING Refer to the table below if the unit does not operate properly. If the problem you are experiencing is not listed below, or if the instruction below does not help, press to enter standby mode, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center. General Problem The speakers make no sound. Cause The volume may be set to the minimum level. Solution Adjust the volume level. The source may be incorrect. Select the correct source.
TROUBLESHOOTING iPod Problem No sound. The iPod does not charge up. Cause Set the iPod firmly. Earphones are connected. Remove the earphones. The proper data is not in the iPod. Check if the proper playable data is in the iPod. For the proper data format or how to put the data into the iPod, refer to the owner’s manual supplied with each product. The iPod software version has not been updated. Download the latest iTunes software to update the iPod software version to the latest.
■ PLAYER SECTION ■ GENERAL iPod/iPhone • • • • • Made for. iPhone 5/iPhone 5c/iPhone 5s iPod touch (5th generation) iPod nano (7th generation) (as of August 2014) • An iPod may not be detected by the unit or some features may not be compatible, depending on the model or software version of the iPod. En SPECIFICATIONS Power Supply........................... AC 100 to 240 V, 50/60 Hz Power consumption .....................................................11 W Standby consumption (Clock displayed) .......
PRECAUCIÓN: LEA LAS INDICACIONES SIGUIENTES ANTES DE UTILIZAR ESTE APARATO 1 2 3 4 5 6 7 8 9 10 11 12 13 Para asegurar el mejor rendimiento de este aparato, lea atentamente este manual. Y luego guárdelo en un lugar seguro para poder consultarlo en el futuro en caso de ser necesario. Instale esta unidad en un lugar bien ventilado, fresco, seco y limpio, alejado de la luz directa del sol, fuentes de calor, vibración, polvo, humedad y frío.
PREPARATION CONTENIDO ■ Características – Reproducción de contenidos de un iPod/iPhone (con conector Lightning), radio FM y dispositivos externos con un conector AUX. – Configuración de alarmas usando un iPod/iPhone (con conector Lightning) o la radio FM. – Suministro de alimentación a un iPod/iPhone (con conector Lightning). – Sonido de una gran riqueza gracias a un altavoz personalizado de gama completa de 5 cm y DSP (procesador de señal digital) de Yamaha.
NOMBRES DE LAS PARTES Y SUS FUNCIONES ■ Panel superior E Base para iPod Conecte el iPod al conector Lightning de la base para iPod. y El iPod se carga cuando esta instalado en la base para iPod. Nota A Rejilla (☞ página 3) B Visor • Es posible que el iPod no se ajuste a la base para iPod de forma segura si está dentro de la caja protectora. • Esta unidad deja de proporcionar alimentación cuando se encuentra en el modo de espera Eco. F VOLUME Controla el volumen.
NOMBRES DE LAS PARTES Y SUS FUNCIONES Precaución ■ Panel posterior A la toma de pared de CA L 12 V Conecte el adaptador de CA suministrado. M AUX Conecte dispositivos externos con cables con miniclavija estéreo de ø3,5 mm. (☞ página 8) N FM ANT Terminal de antena de FM Conexión de la antena de FM A A Conecte la antena suministrada a la unidad. B Coloque la antena en la posición en la que reciba mejor señal. Nota B • Asegúrese de extender la antena tal y como muestra la ilustración.
OPERATION FUNCIONES BÁSICAS Ajuste del reloj A Mantenga pulsado CLOCK durante más de 2 segundos. El visor parpadeará. A, C B B Ajuste la hora con TUNING. y Si mantiene pulsado TUNING, los números avanzan rápidamente. C Pulse CLOCK. Si desea salir del modo de ajuste del reloj, pulse . y Si pulsa PRESET en el paso B, puede seleccionar el método usado para indicar la hora (12 horas/24 horas). Nota El ajuste del tiempo se pierde aproximadamente una semana después de desenchufar la unidad.
FUNCIONES BÁSICAS ■ Activación/Desactivación de la alarma Pulse ALARM. Es Cuando la alarma está activada, el indicador de alarma ( ) y el indicador de RADIO (o el indicador de iPod) se iluminan y la hora de la alarma se muestra durante unos instantes. Indicador de alarma ( ) Indicador de RADIO Indicador de iPod Operaciones durante la reproducción del sonido de la alarma A la hora ajustada, se reproduce el sonido de la alarma. Durante la reproducción, las siguientes operaciones son posibles.
ESCUCHAR EMISORAS DE RADIO Sintonización de emisoras de radio A Pulse SOURCE para seleccionar RADIO. Se iluminará el indicador RADIO. B A B Para la sintonización automática, mantenga pulsado TUNING. Para la sintonización manual, pulse TUNING varias veces. Nota Si sintoniza una emisora de radio manualmente, el sonido es monoaural. Indicador de RADIO Presintonización de emisoras de radio Es posible almacenar hasta cinco emisoras de radio FM favoritas con la función de presintonización.
ESCUCHAR EL iPod ■ Conexión de un iPod a la base para iPod • Puede recargar un iPod mientras está conectado a la base. El iPod no se recargará cuando la unidad esté en el modo de espera Eco. • Si conecta un iPod en su funda protectora utilizando la fuerza, puede provocar daños en el conector. Retire la funda protectora antes de realizar la conexión. Nota • Conecte o desconecte el iPod despacio. • Inserte el iPod en la ranura en posición vertical y en el ángulo correcto, sin realizar ningún tipo de presión.
ESCUCHAR FUENTES EXTERNAS A Conecte el dispositivo de audio portátil al terminal AUX mediante un cable con miniclavija de 3,5 mm disponible en tiendas. Panel posterior A B Nota C Baje el volumen de la unidad y el del dispositivo de audio portátil antes de realizar la conexión. Indicador AUX B Encienda el sistema. C Pulse SOURCE para seleccionar AUX como fuente de reproducción. Se iluminará el indicador AUX. D Inicie la reproducción en el dispositivo de audio portátil conectado.
SOLUCIÓN DE PROBLEMAS General Problema Los altavoces no suenan. Causa Solución Es posible que el volumen esté ajustado al Ajuste el nivel del volumen. mínimo. Es posible que la fuente no sea la correcta. Seleccione la fuente correcta. El sonido se apaga de repente. La unidad está configurando la alarma. Pulse ALARM para finalizar la configuración de la alarma. La función Reposo automático está activada. Encienda el sistema y reproduzca la fuente de nuevo.
SOLUCIÓN DE PROBLEMAS iPod Problema No hay sonido. El iPod no se carga Causa Solución El iPod no está correctamente instalado en Instale el iPod correctamente. la base para iPod. Los auriculares están conectados. Desconecte los auriculares. No hay contenidos compatibles en el iPod. Compruebe si hay contenidos que puedan reproducirse en el iPod.
ESPECIFICACIONES ■ GENERALIDADES iPod/iPhone • Alimentación.................... De 100 V a 240 V CA, 50/60 Hz • Consumo de energía eléctrica ......................................11 W • Consumo en modo de espera (visualización del reloj) ....................................................................................1,0 W • Consumo en modo de espera Eco ...............................0,2 W • Tiempo de gestión de la alimentación (Auto Standby) ................................................
© 2014 Yamaha Corporation Printed in China ZN35200