CVP-509/505/503/501 PSR-S910/S710 Tyros4 Internet Connection Guide v1.10 Enjoy your instrument with Internet Direct Connection This instrument can be directly connected to the Internet, conveniently letting you display and access the special website from the instrument’s display and enjoy the various contents. This guide provides detailed instructions on connecting. You can also refer to the Internet-related terms at the end of this guide.
Selection of the Connection Environment To connect the instrument to the Internet, a full-time online connection (ADSL, optical fiber, cable Internet, etc.) using a broadband router or a modem equipped with a router is necessary. NOTE • Since no broadband router or modem settings can be made by the instrument itself, use a computer to make the settings before connecting to the instrument.
Connection LAN Cable Connection 1 Connect the devices according to the example. First turn the power of the instrument off, then connect the devices as shown in the illustration below, and finally turn the power on again. NOTE • For an illustration of the location of the LAN terminal, refer to the Owner’s Manual. LAN terminal Internet LAN cable Router Modem Required Devices • • • LAN cable Router (This is unnecessary if your modem has router capability.
Connection 3 Use the [DATA ENTRY] dial to select “Set the Internet connection,” then press the [ENTER] button to execute. 4 Use the [A]/[B] buttons to select “SETUP WIZARD.” 5 Press the [B] button to select “LAN cable,” then press the [G] button to proceed to “NEXT.” 6 Make sure that the devices are connected as shown in the illustration of the display, then press the [G] button to proceed to “NEXT.
Connection 7 Press the [G](CONNECTION) button to check the connection to the special website. The settings are saved by checking the connection. NOTE • Because the settings are lost when you turn off the power of the instrument, be sure to save the settings and changes you made. 8 Press the [G](DONE) button to connect to the special website. When the special website appears, the network settings to the Internet are complete.
Connection Wireless LAN Connection Using USB LAN Adaptor 1 Connect the devices according to the example. First turn the power of the instrument off, then connect the devices as shown in the illustration below, and finally turn the power on again. NOTE • For an illustration of the location of the USB TO DEVICE terminal, refer to the Owner’s Manual. Set the instrument within 10–20 m from the access point. The signal will not be received if there is an obstacle blocking reception.
Connection 4 5 6 Use the [A]/[B] buttons to select “SETUP WIZARD.” Press the [C] button to select “Wireless LAN using USB LAN adaptor,” then press the [G] button to proceed to “NEXT.” Make sure that the devices are connected as shown in the illustration of the display, then press the [G] button to proceed to “NEXT.
Connection 7 Use the [B]/[C] buttons to select the desired setup of the wireless network. Setup by WPS (push button) You can make the setting for the wireless network by simply pressing the WPS button of the access point with router. The security is automatically set, you don’t need to make any other settings, such as key input, etc. NOTE • You need to make sure that your USB wireless LAN adaptor and access point with router support WPS.
Connection 8 Press the [F](YES) button, then within 2 minutes hold down the WPS button of the access point with router. For details about the operations in the setting of the access point on the router side, read the owner’s manual for the product you are using. Proceed to step 13. 9 Use the [DATA ENTRY] dial to select the desired access point, then press the [G] button to proceed to “NEXT.” The SSID, channel and security format of the selected access point are automatically set.
Connection 10 Press the [D](KEY) button to call up the character-entry display to input the key. 11 Input the key. Refer to the Owner’s Manual for character-entry details. To cancel the key input, press the [8t](CANCEL) button. 12 Press the [G](NEXT) button to set the key input. When you set the key input, the characters are hidden and displayed as “******.” Make a written note of the settings, in case you have to enter them again.
Connection 13 Press the [G](CONNECTION) button to check the connection to the special website. The settings are saved by checking the connection. NOTE • Because the settings are lost when you turn off the power of the instrument, be sure to save the settings and changes you made. 14 Press the [G](DONE) button to connect to the special website. When the special website appears, the network settings to the Internet are complete.
Connection Wireless LAN Connection Using Wireless Game Adaptor 1 Connect the devices according to the example. First turn the power of the instrument off, then connect the devices as shown in the illustration below, and finally turn the power on again. NOTE • For an illustration of the location of the LAN terminal, refer to the Owner’s Manual. Set the instrument within 10–20 m from the access point. The signal will not be received if there is an obstacle blocking reception.
Connection 2 Press the [INTERNET] button. When the special website appears Since the instrument is connected to the special website, you do not need to make Internet settings. For details on operations in the special website, refer to the Owner’s Manual. NOTE • The special website screen above is taken from the CVP-509. • The contents of the service as appearing here are current as of March, 2010. The available contents of the service are subject to change.
Connection 5 6 7 Press the [D] button to select “Wireless LAN using Wireless Game Adaptor,” then press the [G] button to proceed to “NEXT.” Make sure that the devices are connected as shown in the illustration of the display, then press the [G] button to proceed to “NEXT.” Press the [G](CONNECTION) button to check the connection to the special website. The settings are saved by checking the connection.
Connection Using Static IP Address or Proxy Server Some cases may require detailed knowledge of the network settings. 1 2 Turn the power of the instrument on, then press the [INTERNET] button. Use the [DATA ENTRY] dial to select “Set the Internet connection,” then press the [ENTER] button to execute. 3 Press the [C] button to select “ADVANCED SETTINGS.” 4 Use the TAB [<][>] buttons to call up the desired page.
Connection 5 Use the [A]–[J] buttons to select the desired parameter. 6 Select the setting or change the value. For details on each parameter, refer to page 18. Selecting the setting Use the [2 st]/[3 st] buttons to select the setting, then use the [4 st](OK) button to execute. Changing the value Enter the value, then press the [8 s](OK) button to execute. Refer to the Owner’s Manual for character-entry details.
Connection 7 Use the [7 st] buttons to select “OK.” 8 Press the [G](YES) button to save the settings. NOTE • Because the settings are lost when you turn off the power of the instrument, be sure to save the settings and changes you made. 9 Connect the devices. First turn the power of the instrument off, then connect the devices, and finally turn the power on again. 10 Press the [INTERNET] button to connect to the special website.
Connection Parameters IP INFORMATION DHCP Determines the DHCP ON/ON (SET DNS MANUALLY)/OFF settings. IP ADDRESS/SUBNET MASK/ GATEWAY Determines the IP ADDRESS/SUBNET MASK/GATEWAY settings. These settings must be made when DHCP above is set to “OFF.” DNS SERVER 1/2 These settings must be made when DHCP above is set to “ON (SET DNS MANUALLY)” or “OFF.” PROXY SERVER PROXY SERVER/PROXY PORT Determines the proxy server name and port number. WIRELESS LAN SSID Determines the SSID setting.
Connection Help If the instrument is not connected to the Internet, sometimes the [HELP] button appears on the display. You can view the solutions by selecting “HELP.” 1 Press the [G] button to select “HELP.” Error code For details about each code, refer to the following URL: http://services.music. yamaha.com/idc/faq.html 2 3 Use the [DATA ENTRY] dial to select a solution (Details), then press the [ENTER] button to view the details. Solve the problem with the displayed solutions.
Initialization of the Setup CAUTION • This restores the network settings to the default settings. 1 2 Press the [INTERNET] button. Use the [DATA ENTRY] dial to select “Set the Internet connection,” then press the [ENTER] button to execute. 3 Press the [E] button to select “INITIALIZE SETUP.” 4 Press the [G](YES) button to initialize the settings.
Glossary of Terms Access point A device that allows devices like your Yamaha instrument to connect to the Internet using a wireless network. Some access points are combined with the modem. broadband An Internet connection technology/service (such as ADSL and optical fiber) that allows for highspeed, high-volume data communication.
About Using BSD-Licensed Software The software used by this product includes components that comply with the BSD license. The restrictions placed on users of software released under a typical BSD license are that if they redistribute such software in any form, with or without modification, they must include in the redistribution (1) a disclaimer of liability, (2) the original copyright notice and (3) a list of licensing provisions.